Pass and Seymour d b a Legrand ADMHRM4 Users Manual

ADMHRM4

Wireless Room Scene Remote

Specifications

Power Supply ................Two AAA Alkaline Batteries, provided

Operating Temperature .................32°F to 104°F (0°C to 40°C)

Installation Instructions

UNIT DESCRIPTION

The adorne ADMHRM4 Wireless Room Scene Remote is a room level scene
controller. It provides instant recall of four user-recorded lighting scenes (or
presets) assigned to a room or designated area. It also provides off and on
functions, overall control of the room’s light level, all with convenient, handheld
portability.

It is used to control a variety of adorne wireless devices including dimmers,
switches, plug-in appliance modules and plug-in lamp modules.

The ADMHRM4 is a battery operated portable device, so you can use it to control
its designated room from anywhere in the house. Each ADMHRM4 is assigned
to one room and cannot operate devices that are bound to different rooms (see
(ROOM BINDING).

You can control up to 4 scenes in the room with a ADMHRM4 (see MORE SCENES
section). You can use additional room scene remotes to control those scenes
from multiple locations.

adorne Wireless

adorne wireless devices use radio signals to communicate with each other to
control lighting and other types of electric loads in selected areas. They use the
900MHz band for high-speed control communication. Using the Watt Stopper’s
own “frequency-agile” Top Dog™ technology, adorne wireless devices avoid
interference with other 900MHz devices, such as cordless phones and baby
monitors.

Application Assistance

The adorne Installation Guide provides more information about configuring
scenes. Instructions for installation and use are included with the relevant
adorne wireless devices. Application support information and the adorne

Installation Guide is available online.

SET HOUSE ID

All adorne wireless devices installed in the same home must acquire the same
unique House ID before use. This process is known as house binding. Each
adorne wireless device is bound to all other adorne wireless devices in the
house.

New Installation

1. With all devices installed and
energized, make sure that every
adorne wireless device LED is
orange. If any LED is off, be sure
the circuit breaker is on and the
device is correctly installed. The
ADMHRM4 remote shuts down
when it is not in use. Press any

B

C

D

E

A

When you see
in the instructions,
firmly press and
hold both the top
and bottom of
the paddle until
the LED changes
(about 5 seconds ).

button to activate the remote and illuminate its LED.

2. Press

on any device paddle until the LED flashes orange (about 5 seconds ).

This indicates that it has acquired a unique House ID.

3. Make sure that all other adorne wireless device LEDs are flashing green,
indicating that they have acquired the same House ID. For ADMHRM4
remotes, be sure that the units are awake during the binding process. Press
any button to activate the remote and illuminate its LED.

4. Return to the device used in step 2, which is still flashing orange. Press
until the LED changes to solid white (about 5 seconds ). All device LEDs in the
House change to solid white, indicating house binding is complete.

Adding an ADMHRM4 to an Existing Installation

If you’re adding or replacing a device in a adorne wireless installation that is
already operating, the new device must be bound to the same House ID as the
other adorne wireless devices in the house. After the new ADMHRM4 is powered
up, the LED should be solid orange. This indicates that it has not yet acquired a
House ID. To acquire the House ID for the existing system:

1. Press

2. Be sure that the ADMHRM4 is awake during the binding process. Press any

3. Return to the same previously bound device used in step 1 and press

on any previously bound device until the LED flashes orange (about 5

seconds ).

button to activate the remote and illuminate its LED. Verify that the new
ADMHRM4 LED is flashing green, indicating that it has acquired the House ID.

the LED changes to solid white (about 5 seconds ). All device LEDs should
now be solid white.

until