Paso Sound Products DMS 3040-40, DMS 3080-80, DMS 3120-120, OM163, DMS 3040 Installation Manual And Operating Instructions

...

Download

Innovation through technology since 1931

Installation Manual

and Operating Instructions

7 Channel - 3 Zone - Dual VOX -

Dual Mute - MOH - Vox Relay -

Module Port - Phone Interface

TTOO RREEDDUUCCEE TTHHEE RRIISSKK OOFF FFIIRREE OORR EELLEECCTTRRIICC

SSHHOOCCKK DDOO NNOOTT EEXXPPOOSSEE TTHHIISS AAPPPPLLIIAANNCCEE TTOO

WWAATTEERR,, RRAAIINN OORR MMOOIISSTTUURREE

CAUTION !

REV. 1.5

IMPORTANT NOTE:

THIS OPERATING MANUAL IS PROVIDED AS AN INSTALLATION AND AS AN OPERATING AID. PASO SOUND PRODUCTS, INC. DOES NOT ASSUME ANY RESPONSIBILITY AS TO ITS ACCURACY AND SHALL NOT BE LIABLE IN TORT OR CONTRACT FOR ANY DIRECT CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE ARISING FROM THE INSTALLATION, USE OR INABILITY TO USE THIS PRODUCT.

DDMMSS 33004400 -- 4400 WWaatttt RRMMSS

DDMMSS 33008800 -- 8800 WWaatttt RRMMSS

DDMMSS 33112200 -- 112200 WWaatttt RRMMSS

PROFESSIONAL AUDIO & SOUND

Series DMS

Integrated Amplifiers

Manual

OOMM 116633

DDiiggiittaall MMuussiicc AAmmpplliiffiieerrss

DIGITAL MUSIC SERIES

LISTED

COMMERCIAL

AUDIO

EQUIPMENT

30TJ

DESCRIPTION AND APPLICATIONS SPECIFICATIONS

PAGE 2

DMS3040/3080/3120

Power Output:

DMS3040 DMS3080

DMS3120 Distortion: Frequency Response: Inputs:

Input 1

Input 2

Input 3

Input 4

Input 5

Input 6

Input 7 Sensitivity & Z:

Input 1

Input 2

Input 3

Input 4

Input 5

Input 6

Input 7

AUX 1 Input Attenuator:

AUX 2 Input Attenuator: Phantom Power: Hum & Noise: Telephone Paging Input: Accessory Port: EQ LINK: Line Outputs: Inputs/Outputs: Subwoofer Outputs: Subwoofer Output Level: Music on Hold Output: Zone 2 Output: Zone 3 Output: Main Output Impedance: Controls:

Front Panel:

Rear Panel:

Bass and Treble Controls: Tone By-Pass: Remote Volume Controls: MOH Source Selection: Zone 2/3 Source Selection: DUAL VO X: VOXBUSS 1: VOXBUSS 2: MUTE BUSS 1: MUTE BUSS 2: MUTE 2 DELAY: Unmuting: Power Supply Output: Auto VO X Relay:

Rack Mounting: Internal Cooling Fan: Power Requirement: Power Consumption:

AC Accessory Outlet: Terminations: Housing Finish: Output Power Indicator: Dimensions: Net Weight:

DMS3040 DMS3080 DMS3120

UNPACKING

Immediately upon receipt of the amplifier, inspect the unit and shipping container for indications of improper handling or in transit damage.The equipment was carefully inspected and tested before leaving the factory. Notify the Transportation Company immediately if any damage is found. ONLY THE CONSIGNEE CAN FILE A CLAIM WITH THE CARRIER FOR DAMAGE DURING SHIPMENT. Be sure to save the carton and packing material as evidence of damage for the shipper inspection. DO NOT SHIP the unit back to the factory unless authorized by the factory.

IN TRANSIT DAMAGES ARE NOT COVERED BY THE PASO WARRANTY.

40 Watt RMS 80 Watt RMS 120 Watt RMS Less than 0.5% THD 20 - 20,000 Hz ± 1 db

Microphone 1 Balanced Microphone 2 Balanced Microphone 3 Balanced Microphone 4 Balanced - AUX 1

(Stereo Summing)

Microphone 5 Balanced - AUX 2

(Stereo Summing)

Telephone Interface - Transformer Balanced Module Port

Mic 1

= 1.5 Mv - 250 ohm

Mic

2 = 1.5 Mv - 250 ohm

Mic 3

= 1.5 Mv - 250 ohm

Mic 4

= 1.5 Mv - 250 ohm - AUX 1 = 100 Mv - 47K

ohm

Mic 5

= 1.5 Mv - 250 ohm - AUX 2 = 100 Mv - 47K

ohm

Tel

=100 Mv - 600 ohm - Transformer Balanced

Module

= 1 V - 47K ohm Variable (rear panel control) Variable (rear panel control) All Microphone Inputs by internal jumper (18 V)

Mic

-70 db,

Aux

-75 db 600 ohm Transformer balanced Accepts Standard Module Preamp out, Power Amp in with EQ Link Switch Line Out 600 ohm - 1.5 V loaded MIX BUSS Pre-EQ and Post-EQ Outputs 1 Volt 600 ohm-1 Volt Transformer Balanced 1 Watt-8 ohm with Control 1 Watt-8 ohm with Control 8 ohm, 25 Volt and 70 Volt line

Input 1 Level, Input 2 Level, Input 3 Level, Input 4 Level, Input 5 Level, Module Level, Bass and Treble PHONE Level - AUX 1 Attenuator - AUX 2 Attenuator

- MOH/ZONE 1 Level Control - ZONE 2 Level Control

- VOX 1/VOX 2 Sensitivity - MUTE 2 Delay ± 10 dB at 100 Hz and 10 KHz On - Off Switch

(rear panel)

AUX 1 Input Level and Master Volume (10 K) AUX 1 - AUX 2 - MODULE by internal jumper AUX 1 - AUX 2 - MODULE by internal jumper Voice Activated Muting Available on all 7 Inputs by internal jumpers Available on all 7 Inputs by internal jumpers Available on all 7 Inputs by internal jumpers Available on all 7 Inputs by internal jumpers Adjustable from 3 Sec to 30 Sec (rear panel control) MUTES/UNMUTES MIC 1 only 24 V DC - 250 mA Regulated NO/NC Contacts - VOX activated - Contacts Rating = 30 VDC - 7 A Optional Model 27/3501 - 19” Rack Kit 3” Thermally Controlled -

Model DMS3120 only

117 Volt, 50-60 Hz

DMS3040 = AC = 630 VA - DMS3080 = 750 VA - DMS3120 = 850VA Max.

500 W Max. Unswitched Screw Ter minals, RCA Jacks Black Multi-color LED

(front panel)

19” W., 12”D., 4” H. with feet

(482X305X102 mm)

3.5”

(89 mm)

. less feet

16 Lbs

(8 Kg)

19 Lbs

(8.5 Kg)

22 Lbs

(11 Kg)

❑❑

High Performance - High Reliability Design

❑❑

Wide Frequency Response - Very Low Distortion

❑❑

7 Channel Inputs - 3 Zone Outputs

❑❑

5 Balanced Microphone Inputs

❑❑

Phantom Power on all MIC Inputs

❑❑

MIC 4/AUX 1 and MIC 5/AUX 2 Inputs

With Stereo Summing

❑❑

AUX1 and AUX2 Inputs Attenuator

❑❑

600 ohm Transformer Balanced

Telephone Paging Input

❑❑

MIX Buss and 600 ohm Line Output

❑❑

Independent Input Controls

❑❑

Rear Panel Port: Accepts Standard Module

❑❑

Independent Module Level Control

❑❑

AUX1 and Master Remote Volume Controls

❑❑

External EQ Link

❑❑

Tone by-pass and EQ Link switches

❑❑

Pre-EQ Subwoofer Output

❑❑

Post-EQ Subwoofer Output

❑❑

Addressable Dual VOX Buss

Voice Activated Muting

❑❑

VOX Variable Time Delay Function

❑❑

Addressable Dual MUTE Buss

❑❑

Direct Muting and Unmuting

❑❑

600 ohm and 8 ohm 1 Watt

Music on Hold Amplifier

❑❑

MOH Amplifier Source Selector

❑❑

Zone 2 and 3, 1 Watt - 8 ohm Output

with Separate Control

❑❑

NO/NC VOX Operated Relay

❑❑

24 V DC 250 mA Regulated Power Supply Output

❑❑

8 ohm, 25 Volt & 70 Volt Output

❑❑

Optional 19” Rack Mounting with Kit

❑❑

Low profile - 2-Unit of Vertical Rack space

❑❑

UL 6500 Listed (US - CANADA)

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PAGE 3

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

RACK MOUNTING

A) Procure the optional accessory Rack Mount Kit Model 27/3501. B) Turn amplifier up side down and remove the four rubber feet by unscrewing the four holding screws. C) Remove two screws on each side of the amplifier holding the amplifier cover. D) Install the rack kit brackets by using the self-tapping screws provided.

DMS

Fig. 3 - Rack Kit Mounting

READ BEFORE OPERATING READ BEFORE OPERATING

BEFORE OPERATING THE AMPLIFIER, BE SURE YOU FULLY UNDERSTAND ALL INSTRUCTIONS AND FEATURES OF THE UNIT.

Read these instructions carefully.

Keep these instructions.

Heed all Warnings.

Follow all instructions.

5) DO NOT use this apparatus near water.

6) Clean ONLY with a damp cloth.

7) DO NOT block any of the ventilation openings.

Install in accordance with the instructions provided.

8) DO NOT install near any heat sources such as radiators, stoves, or other apparatus (including amplifiers) that produce heat.

9) DO NOT mount amplifier into a container or a closed unventilated closet while operating.

10) DO NOT place any object or accessory equipment such as Tuners, Mixers, Cassette Decks, etc.on top of the amplifier. Obstructing or closing the cabinet ventilation openings may cause overheating.

11) DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other .A grounding type plug has two blades and a third grounding prong.The wide blade and or the third prong is provided for your safety. When the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

12) Use only the attachments and accessories specified in this manual.

13) If a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tipover.

14) Unplug this apparatus during lighting storms or when unused for long periods of time.

15) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have f allen into the appar atus, the appar atus has been exposed to rain or moisture, does not operate normally, or has been dropped.

16) DO NOT replace fuses unless power cord is removed from the AC wall outlet.

17) DO NOT install accessories unless the power cord is removed from the AC wall outlet.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO WATER, RAIN OR MOISTURE

IMPORTANT SAFETY INSTRUCTIONS

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

DMS

DIGITAL MUSIC SERIES

100 100 100 100 100 100 +10-10 +10-10

INPUT 1 INPUT 2 INPUT 3 INPUT 4/AUX 1 INPUT 5/AUX 2 BASS TREBLEMODULE

DIGITAL MUSIC AMPLIFIER

PROFESSIONAL AUDIO & SOUND

OUTPUT LEVEL

POWER

PEAK

PAGE 4

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

DMS

1) INPUT 1 Volume Control

2) INPUT 2 Volume Control

3) INPUT 3 Volume Control

4) INPUT 4/AUX 1 Volume Control

5) INPUT 5/AUX 2 Volume Control

6) Input Module Level Control

7) BASS Control

8) TREBLE Control

9) On-Off Power Switch

10) Output Level Meter

Fig. 4 - FRONT PANEL CONTROLS

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

PEAK

DIGITAL MUSIC SERIES

OUTPUT LEVEL

PROFESSIONAL AUDIO & SOUND

POWER

DIGITAL MUSIC AMPLIFIER

DIGITAL MUSIC SERIES

DMS

5 6 7 8 9

2 3 4

100 100 100 100 100 100 +10-10 +10-10

INPUT 1 INPUT 2 INPUT 3 INPUT 4/AUX 1 INPUT 5/AUX 2 BASS TREBLEMODULE

PAGE 5

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

Fig. 5- REAR PANEL INPUTS - OUTPUTS - CONTROLS

1) Unswitched AC Auxiliary Socket

2) ZONE 1 - Output Level Control

3) Zone 1 MOH - 600 ohm, 1 Volt Output

4) Zone 1 - 8 ohm, 1 Watt Output

5) Zone 2 - 8 ohm, 1 Watt Output

6) ZONE 2 - Output Level Control

7) VOX Relay NO/NC Contact Terminals

8) 24 Volt DC Regulated Power Supply Output

9) MIC 1 UNMUTE

10) MUTE 1 - MUTE 2 Terminals

11) Master Remote Volume Control Terminals

12) EQ LINK - IN - OUT Switch

13) EQ LINK - PREAMP. OUT/POWER AMP IN

14) SUB OUT - PRE EQ and POST EQ

15) MIX BUSS

16) LINE OUT 600 Ohm

17) TONE BYPASS - ON/OFF SWITCH

18) AUX 1 Input Attenuator

19) INPUT 4/AUX 1 - Stereo Summing Jacks

20) INPUT 5/AUX 2 - Stereo Summing Jacks

21) AUX 2 Input Attenuator

22) Standard Module Port

23) TELEPHONE Paging Output Level Control

24) TELEPHONE Paging Balanced Input 600 Ohm

25) INPUT 5/AUX 2 - Balanced Input

26) INPUT 4/AUX 1 - Remote Volume Control Ter minals

27) INPUT 4 - Balanced MIC Input

28) INPUT 3 - Balanced MIC Input

29) INPUT 2 - Balanced MIC Input

30) INPUT 1 - Balanced MIC Input

31) MUTE 2 Time Delay Control

32) VOX 2 Sensitivity Control

33) VOX 1 Sensitivity Control

34) Speaker Output Terminals

35) Chassis Ground

36) AC LIne Fuse

37) AC Power Cord

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

MODULE

STANDARD

PORT ACCEPTS

47kohm 100mV

INPUT-5(AUX2)

(AUX2)

ATTENUATOR

INPUT 5

INPUT-4(AUX1)

47kohm 100mV

MIX

BUSS

PRE EQ

SUB OUT

PRE

OUT

30TJ

AUDIO

LISTED

EQUIPMENT

COMMERCIAL

CUS

RVC

MASTER

REMOTE

VOLUME MUTE 1

M1 RVC

MUTE 2

GROUND

UNMUTE

MIC1 G M2

24V DC

250 mA

VOX RELAY

NC C NO

ZONE 2

(AUX1)

ATTENUATOR

EQ LINK

LEVEL

OFF

TONE

LINE OUT

SUB OUT

POWER

EQ LINK

IN OUT

CAUTION

RISK OF ELECTRIC SHOCK

DMS3120

PROFESSIONAL AUDIO & SOUND

CAUTION: REMOVE

SWITCH

MIC-AUX2

BY INTERNAL

TEL OUTPUT

TEL

BYPASS

AUX2

47Kohm 100 mV

INPUT5 (MIC-AUX2)

600

INPUT 4

VOLUME

REMOTE

POST EQ

INPUT 4 (MIC) INPUT 3 (MIC)

INPUT 2 (MIC)

DO NOT OPEN

MUST BE EARTHED

INPUT 1 (MIC)

WARNING: THIS APPLIANCE

850 VA

120 W RMS

117V 60 HZ

VOX-2 MUTE-2

DIGITAL MUSIC AMPLIFIER

POWER RATING

SUPPLY VOL TAGE

POWER CONSUMPTION

INSTALLING MODULE

POWER CORD FROM

AC OUTLET PRIOR TO

LEVEL

G COM HOT

G COM HOT RVC RVC G COM HOT G COM HOT G COM HOT G COM HOT

DELAY

SENS

VOX-1

600 ohm 100mV

BALANCED

250ohm 1.5mV

SER. NO.

2425262728293031323334

0 8

ZONE 2

0 8

ZONE 1

0 600

AFIN DE REDUIRE LE RISQUE

LEVEL

ZONE 1

ATTENTION:

D'INCENDIE REMPLACER SEUL PAR UN

FUSIBLE DE MEME TYPE.

CAUTION: TO REDUCE THE

RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE

FUSE.

1 WA TT

ATTENTION: POUR REDUIRLES RISQUES D' INCENDIE

OU DE CHOC ELECTRIQUE, NE PAS EXPOSER A LA PLUIE

OU L' HUMIDITE, NE PAS ENLEVER LE COUVERCLE. AUCUN

REGLAGE A L' INTERIEUR. POUR REPARATION CONSULTER

UNE PERSONNE QUALIFIEE

COM 8 25V 70V

BALANCED

MOH OUT

GROUND

CAUTION: TO REDUCE THE RISK OF FIRE OR

SHOCK DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE. DO NOT REMOVE COVER.

THERE ARE NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

UNSWITCHED

117V 500W MAX

SPEAKER OUTPUT

CLASS 2 WIRING ACCEPTABLE

DMS3120 Rear Panel

Manual

5A 250V

LINE FUSE

117V 60HZ

PAGE 6

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

Fig. 6 - MAIN PCB AND MOH BOARD TOP VIEW

FUNCTION SWITCHES AND JUMPERS LOCATION

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

SOCKET

OPTIONAL

CHIME CARD

CN 213

DIGITAL MUSIC SERIES

REV - 0

DMS3120 - 7

M. O. H. BOARD

DMS3120 - 7

M.O.H. BOARD

SW206

VOX RELAY

MIC 1

SW201

POWER

ON OFF

PHANTOM

MIC 2

SW202

POWER

ON OFF

PHANTOM

MIC 3

SW203

POWER

ON OFF

PHANTOM

AMPLIFIER REAR PANEL

MIC 4

SW204

POWER

ON OFF

PHANTOM

SW228

INPUT 4

SWITCH

AUX1 MIC4

POWER

PHANTOM

INPUT5

AUX2 MIC5

INPUT5

MIC 5

SW207

SWITCH

AUX2 MIC5

ON OFF

SW229

AUX2 MIC5

SW208

AUX2 MIC5

MODULE

SW205

ON OFF

MIC1 UNMUTE

M2 M1

INPUT 1

INPUT 2

INPUT 3

INPUT 4

REMOTE

AUX 2

TEL

INPUT

SW209

AUX1 AUX2

SOURCE SWITCH

SW227

M2 M1

CHIME TRIGGER

(MIC)

VOLUME

INPUT 5

SW227

M2 M1

(CHIME TRIGER)

ON OFF

SW205

(UNMUTE)

M2 M1

SW206

(VOX RELAY)

ON OFF

SW201 (MIC1)

SW215

INPUT1

V2 V1 OFF

SW220

INPUT1

SW219

INPUT2

SW218

(INPUT4/AUX1)

SW223

INPUT5/AUX2

(TEL)

SW216

V2 V1 OFF

M2 M1 OFF

V2 V1 OFF

INPUT3

SW217

V2 V1 OFF

M2 M1 OFF

SW221

SW222

M2 M1 OFF

SW210

M2 M1 OFF

SW211

M2 M1 OFF

SW212

V2 V1 OFF

M2 M1 OFF

SW213

V2 V1 OFF

(MODULE)

INPUT2

T204

INPUT3

(INPUT4/AUX1)

(TEL)

SW214

HOT COM GND HOT COM GND

ON OFF

SW202 (MIC2)

ON OFF

SW203 (MIC3)

HOTRVC RVC COM GNDHOT COM GNDHOT COM GND HOT COM GND

ON OFF

SW204 (MIC4)

SW207

SW208

(INPUT5)

(MIC5)

ON OFF

AUX2 MIC

SW209

(MODULE IN)

AUX2 AUX1

SW228

(INPUT4)

AUX1 MIC4

SW229

(INPUT5)

AUX2 MIC5

REAR PANEL

IT - 5000

(INPUT5/AUX2)

ZONE 1

SW702

AUX2 AUX1 MOD

ZONE 1

SW701

AUX2 AUX1 MOD

SW220

M1 M2 OFF

SW219

M1 M2 OFF

SW218

M1 M2 OFF

SW217

M1 M2 OFF

SW223

M1 M2 OFF

SW216

M1 M2 OFF

SW222

M1 M2 OFF

SW702

ZONE 2

JUMPER

AUX2 AUX1 MODULE

INPUT1

JUMPER

MUTE1 MUTE2

INPUT2

JUMPER

MUTE1 MUTE2

INPUT3

JUMPER

MUTE1 MUTE2

JUMPER

INPUT4 AUX1

MUTE1 MUTE2

JUMPER

INPUT5 AUX2

MUTE1 MUTE2

JUMPER

TEL PAGING

MUTE1 MUTE2

JUMPER

MODULE

MUTE1 MUTE2

ZONE 1

AUX2 AUX1 MOD

SW215

V1 V2 OFF

SW210

V1 V2 OFF

SW211

V1 V2 OFF

SW212

V1 V2 OFF

SW213

V1 V2 OFF

SW214

V1 V2 OFF

SW221

V1 V2 OFF

JUMPER

AUX2 AUX1 MODULE

INPUT1

JUMPER

VOX1 VOX2

INPUT2

JUMPER

VOX1 VOX2

INPUT3

JUMPER

VOX1 VOX2

JUMPER

VOX1 VOX2

INPUT4 AUX1

JUMPER

VOX1 VOX2

INPUT5 AUX2

JUMPER

TEL PAGING

VOX1 VOX2

JUMPER

MODULE

VOX1 VOX2

DMS3120 - 1

MAIN BOARD

PAGE 7

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

DMS3040/3080/3120

FUNCTION SWITCHES AND JUMPERS DEFAULT SETTING TABLE

SW201 INPUT 1 - PHANTOM POWER ON - OFF OFF SW202 INPUT 2 - PHANTOM POWER ON - OFF OFF SW203 INPUT 3 - PHANTOM POWER ON - OFF OFF SW204 INPUT 4 - PHANTOM POWER ON - OFF OFF SW205 INPUT 1 (MIC 1) - UNMUTE ON - OFF OFF SW206 VOX RELAY - MUTE 1 - MUTE 2 M1 SW207 INPUT 5 - PHANTOM POWER ON - OFF OFF SW210 INPUT 2 - VOX 1 - VOX 2 - OFF OFF SW211 INPUT 3 - VOX 1 - VOX 2 - OFF OFF SW212 INPUT 4 - VOX 1 - VOX 2 - OFF OFF SW213 INPUT 5 - VOX 1 - VOX 2 - OFF OFF SW214 TEL IN - VOX 1 - VOX 2 - OFF V1 SW215 INPUT 1 - VOX 1 - VOX 2 - OFF V1 SW216 TEL IN - MUTE 1 - MUTE 2 - OFF OFF SW217 INPUT 4/AUX 1 - MUTE 1 - MUTE 2 - OFF M1 SW218 INPUT 3 - MUTE 1 - MUTE 2 - OFF OFF SW219 INPUT 2 - MUTE 1 - MUTE 2 - OFF OFF SW220 INPUT 1 - MUTE 1 - MUTE 2 - OFF OFF SW221 MODULE - VOX 1 - VOX 2 - OFF OFF SW222 MODULE - MUTE 1 - MUTE 2 - OFF OFF SW223 INPUT 5/AUX 2 - MUTE 1 - MUTE 2 - OFF M1 SW227 CHIME TRIGGER - MUTE 1 - MUTE 2 M1

JUMPER AND JUMPER FUNCTION FACTORY FACTORY

SWITCH ID NO. REFERENCE DESCRIPTION SETTING SETTING

MAIN PCB JUMPERS

SW208 INPUT 5 - MIC 5 OR AUX 2 SWITCH AUX 2 SW209 MODULE IN SOURCE - AUX 1 OR AUX 2 SWITCH AUX 1 SW228 INPUT 4 - MIC 4 OR AUX 1 SWITCH AUX 1 SW229 INPUT 5 - MIC 5 OR AUX 2 SWITCH AUX 2

SWITCHES

SW701 ZONE 2 INPUT SOURCE - AUX 1 - AUX 2 - MODULE AUX 1 SW702 ZONE 1 INPUT SOURCE - AUX 1 - AUX 2 - MODULE AUX 1

MOH BOARD JUMPERS

SW301 TONE BYPASS Defeats Front Panel Bass & Treble SWITCH OFF SW302 EQ LINK Inser ts Exter nal EQ between SWITCH OUT

Preamp out and Power Amp Input

REAR PANEL SWITCHES

THE FOLLOWING INSTRUCTIONS REQUIRE THE REMOVAL OF THE AMPLIFIER PROTECTIVE COVER AND ARE PROVIDED FOR USE BY QUALIFIED PERSONNEL ONLY.

TO AVOID THE RISK OF ELECTRICAL SHOCK DO NO T PERFORM ANY INSTALLA TION OR SERVICING UNLESS YOU ARE QUALIFIED TO DO SO. REFER INSTALLATION OR SERVICING TO QUALIFIED PERSONNEL.

CAUTION !

REMOVAL OF THE AMPLIFIER COVER PRESENTS AN ELECTRICAL SHOCK HAZARD

ALWAYS REMOVE THE POWER CORD FROM THE AC WALL OUTLET

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PAGE 8

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

FUNCTION SWITCHES AND JUMPERS

UNDERSTANDING THE INPUT FUNCTIONS

DUAL VOX AND DUAL MUTE - The Amplifier provides two inde-

pendent VOX (V1 & V2) and two MUTE (M1 & M2) SYSTEMS FUNCTION SOCKETS - EACH INPUT IS PROVIDED WITH A

VOX (V1 & V2) AND A MUTE (M1 & M2) SOCKET. INPUTS VOX AND MUTE FUNCTION - All Inputs including the

Module provide 2 - VOX SEND and 2 MUTE RECEIVE functions. The V OX and MUTE functions are SWITCHED-ON, on each Input, by Internal Jumpers provided for each Input. Two VOX BUSS SEND (V1 & V2) and two MUTE BUSS RECEIVE (M1 & M2) can be independently or simultaneously SWITCHED-ON to suit the application requirement.

Fig. 8 - Any Input VOX and MUTE Functions

JUMPER SETTINGS - The VOX and MUTE Functions are

SWITCHED-ON or OFF by setting the JUMPERS on the VOX (A) and MUTE (B) SOCKET. See Fig. 8A.

The SOCKETS are located on the Main PCB inside the Amplifier as shown on the SWITCHES and JUMPERS LOCATION DIAGRAM in this Manual.Each Socket is identified by an ID NUMBER and the FUNCTION and DEFAULT settings are listed on the FUNCTION SWITCHES and JUMPERS DEFAULT SETTING TABLE in this Manual.

TO SET: Lift the Jumper and reset as required. making sure that the JUMPER is properly positioned over the two shorting pins.

The VOX JUMPER has three positions: OFF,V1 and V2 The MUTE JUMPER has three positions: OFF, M1 and M2

Fig. 8B - Any Input VOX 1 and MUTE 2 Activated

The figure below shows how the VOX 1 Logic Switch and the MUTE 2 Logic Switch are SWITCHED-ON by moving the Jumpers from the OFF position to the V 1 and M 2 position.When the Input is activated by a Source signal the corresponding VOX Signal is sent to the V1 BUSS .When the VOX 2 is activated by another Input the MUTE Signal is present on the MUTE 2 BUSS and it will MUTE this Input

SETTING THE VOX AND MUTE JUMPERS

Fig. 8A - VOX and MUTE Sockets

More than one JUMPER may be used on a VOX SOCKET as shown below. In this example both the VOX 1 and VOX 2 functions are SWITCHED -ON when the Input is activated.For this purpose additional JUMPERS are packed with each Amplifier.

SETTING MORE THAN ONE FUNCTION

More than one JUMPER may be used on a MUTE SOCKET as shown below. In this example both the MUTE 1 and MUTE 2 functions will MUTE this INPUT when either VOX 1 or VOX 2 are activated by other INPUTS.

NOTE: BE SURE NOT TO SET BOTH THE VOX AND CORRESPONDING MUTE ON THE SAME INPUT OR THE INPUT WILL MUTE ITSELF WHEN ACTIVATED.

EXAMPLE: INPUT 1 - V 1 and M 1 BOTH ON.

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

VOX SEND

SOURCE IN

ANY

AUDIO OUT

TO V OX BUSS 1 TO V OX BUSS 2

INPUT

MUTE RECEIVE

DMS Anyinput

FROM MUTE BUSS 1 FROM MUTE BUSS 2

OFF

VOX SEND

SOURCE IN

ANY

AUDIO OUT

JUMPER

SW215

VOX 2 BUSS ON

VOX 2 BUSS OFF

JUMPER

INPUT

SW220

MUTE RECEIVE

DMS Anyinput 02

OFF

MUTE 1 BUSS OFF

JUMPER

MUTE 2 BUSS ON

SOCKET

ID NO.

OFF

V 1

Vox Mute Socket

VOX JUMPERS

SOCKET

SW215

JUMPER JUMPER

V 2

MUTE JUMPERS

SOCKET

SW220

OFF

M 1

M 2

JUMPER

OFF

JUMPER

Vox Socket 01

V 1

V 2

JUMPER

VOX SOCKET

OFF

JUMPER

MUTE SOCKET

M 1

M 2

Mute Socket 01

JUMPER

VOX 1 BUSS ON

VOX 2 BUSS ON

MUTE 1 BUSS ON

MUTE 2 BUSS ON

PAGE 9

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

FUNCTION SETTINGS EXAMPLES

EXAMPLE 9

EXAMPLE 9B

EXAMPLE 9A

EXAMPLES

EXAMPLE 9 - INPUT 1 (MIC 1) mutes INPUT 4/AUX 1. When the Microphone is activated the Music on AUX 1 is muted.

EXAMPLE 9A - INPUT 1 (MIC 1) and TEL IN (Phone Paging) both mute INPUT 4/AUX 1. When the Microphone or the Phone Paging are activated the Music on AUX 1 is muted.The Microphone has priority over the Phone Paging.When MIC 1 is activated both the Phone Paging and the Music on AUX 1 are muted.

EXAMPLE 9B - INPUT 1 (MIC 1) mutes INPUT 4/AUX 1 and INPUT 5/AUX 2. INPUT 4 (Jukebox) mutes INPUT 5 (Sat. Rcvr). When the Jukebox is turned-On the Background Music on AUX 2 is muted. MUTE 2 DELAY (Reference 31) Control is provided.The Microphone Paging has priority over the Background Music and the Jukebox.

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

VOX SEND

MIC IN

WHEN MIC 1 IS ACTIVATED THE VOX 1 BUSS IS SWITCHED-ON AND THE SIGNAL PRESENT ON THE MUTE 1 BUSS WILL MUTE INPUT 4/AUX 1

VOX SEND

MUSIC

WHEN MIC 1 IS ACTIVATED THE VOX 1 BUSS IS SWITCHED-ON AND THE SIGNAL PRESENT ON THE MUTE 1 BUSS WILL MUTE THE MUSIC FROM INPUT 4/AUX 1

MUTE RECEIVE

VOX - MUTE JUMPERS SETTING

INPUT 4

AUX 1

Input 1-4 - V1 - 01

MIC OUT

MUSIC OUT

INPUT 1

MUTE RECEIVE

OFF

X X

JUMPER

SW215

SW220

JUMPER

SW212

SW217

JUMPER

VOX 1 BUSS ON

VOX 2 BUSS OFF

JUMPER

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

VOX 1 BUSS OFF

X X

VOX 2 BUSS OFF

MUTE 1 BUSS ON

MUTE 2 BUSS OFF

VOX - MUTE JUMPERS SETTING

MIC IN

WHEN MIC 1 IS ACTIVATED THE VOX 1 BUSS AND THE VOX 2 BUSS ARE SWITCHEDON AND THE SIGNALS PRESENT ON THE MUTE 1 & 2 BUSS WILL MUTE THE INPUT 4/AUX 1 AND

INPUT 5/AUX 2

JUKEBOX

WHEN INPUT 4AUX 1 IS ACTIVATED THE VOX 2 BUSS IS SWITCHED-ON AND THE SIGNAL PRESENT ON THE MUTE 2 BUSS WILL MUTE THE MUSIC FROM

INPUT 5/AUX 2

MUTE-2 DELAY

3 to 30 Sec

MUSIC

INPUT 5/AUX 2 IS MUTED BY BOTH INPUT

4/AUX 1 AND INPUT 1

WHEN ACTIVATED.

INPUT 1

INPUT 4

AUX 1

INPUT 5

AUX 2

Input 1-4 -5 - 03

MIC OUT

JUKEBOX OUT

MUSIC OUT

OFF

X X

JUMPER

SW215

SW220

JUMPER

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

JUMPER

SW212

SW217

MUTE 1 BUSS ON

JUMPER

SW213

SW223

MUTE 1 BUSS ON

JUMPER JUMPER

MUTE 2 BUSS ON

VOX 1 BUSS ON

VOX 2 BUSS OFF

JUMPER

VOX 1 BUSS OFF

VOX 2 BUSS ON

VOX 1 BUSS OFF

X X

VOX 2 BUSS OFF

MUTE 2 BUSS OFF

VOX 1 BUSS

MUTE 1 BUSS

VOX 1 BUSS

MUTE 1 BUSS

VOX 2 BUSS

MUTE 2 BUSS

VOX 2 BUSS

MUTE 2 BUSS

VOX - MUTE JUMPERS SETTING

SW215

SW220

JUMPER

X X

SW214

SW216

JUMPER

SW212

SW217

JUMPER

VOX 1 BUSS ON

VOX 2 BUSS ON

JUMPER

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

VOX 1 BUSS ON

VOX 2 BUSS OFF

MUTE 1 BUSS OFF

MUTE 2 BUSS ON

VOX 1 BUSS OFF

X X

VOX 2 BUSS OFF

MUTE 1 BUSS ON

MUTE 2 BUSS OFF

VOX 1 BUSS

VOX 2 BUSS

MUTE 1 BUSS

MUTE 2 BUSS

VOX SEND

MIC IN

WHEN MIC1 IS ACTIVATED THE VOX 1 BUSS AND THE VOX 2 BUSS ARE SWITCHEDON AND THE SIGNALS PRESENT ON THE MUTE 1 & 2 BUSS WILL MUTE THE TEL INPUT AND INPUT 4/AUX 1

VOX SEND

TEL IN

WHEN THE TEL INPUT IS ACTIVATED THE VOX 1 BUSS IS SWITCHED-ON AND THE SIGNAL PRESENT ON THE MUTE 1 BUSS WILL MUTE INPUT 4/AUX 1

MUTE RECEIVE

VOX SEND

MUSIC

WHEN MIC1 OR TEL ARE ACTIVATED THE VOX 1 BUSS IS SWITCHED-ON AND THE SIGNAL PRESENT ON THE MUTE 1 BUSS WILL MUTE THE MUSIC FROM

INPUT 4/AUX 1

MUTE RECEIVE

INPUT 1

MUTE RECEIVE

TEL INPUT

INPUT 4

AUX 1

Input 1-4 -Tel - 01

MIC OUT

PHONE OUT

MUSIC OUT

OFF

PAGE 10

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

INPUT 1 SETTING AS A MICROPHONE INPUT

MICROPHONE TYPE

The Microphone Input accepts Low Impedance (250-600 ohm) Dynamic Microphones.The Microphone may be a balanced output type (three wire) or an unbalanced output type (two wire).

PASO MICROPHONES

All PASO low impedance Microphones have a balanced output for best performance. Connect the RED lead to terminal HOT, the WHITE lead to terminal COM and the SHIELD to terminal G.

WIRING

CABLE

MICROPHONE INPUT

Attach the microphone leads to the terminal strip as per diagrams at left.

DO NOT GROUND THE MICROPHONE CABLE SHIELD TO THE CHASSIS OF THE AMPLIFIER

BALANCED MICROPHONE

IMPORTANT NOTE: The use of an unbalanced Microphone (two leads) is not recommended. For best results in a PA Application always use a Unidirectional Dynamic, Low Impedance, Balanced Microphone (three leads).

UNBALANCED MICROPHONE

Attach the Microphone leads to the terminal strip as per diagram in Fig 8A.The cable length should not exceed: 15 Ft. (4.5 m).

Fig. 10 - Balanced Microphone Input 1 Wiring

CAUTION:

TO PREVENT POSSIBLE DAMAGE TO SPEAKERS OR THE AMPLIFIER

ALL INPUT CONNECTIONS MUST BE MADE WITH THE AMPLIFIER POWER OFF.

CABLE LENGTH - If the distance between the Microphone and the Amplifier Input is greater than 15 ft (4.5 m) a Balanced Microphone must be used. Use a two conductor shielded wire and connect Microphone to Amplifier as per Diagram in Fig. 10.

MICROPHONE CABLE ROUTING - The Microphone Cable should be carefully routed. Improper Cable routing will cause spurious oscillations, regenerative noises, hum, etc. that may permanently damage the Amplifier.

z Do not route cable next to power

lines.

Do not route cable near or over Fluorescent Fixtures.

Do not route cable next to Speaker Wires.

Do not install cable inside Power Line Conduits.

Avoid the use of staples that may penetrate the cable.

Fig. 10A - Unbalanced Microphone Input 1 Wiring

INSTALLATION AND WIRING

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

THREE LEADS BALANCED MICROPHONE WIRING

VOX - MUTE JUMPERS SETTING

VOX SEND

MIC IN

Input 1 - V1 - 01

MUTE RECEIVE

The microphone leads color refers to Paso Microphones only. When using other brand refer to instructions packed with that unit.

INPUT 1

OFF

AUDIO OUT

OFF

X X

SHIELD

SW215

VOX 1 BUSS ACTIVATED

JUMPER

VOX 2 BUSS OFF

JUMPER

SW220

JUMPER

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

MIC

Lo Z

INPUT 1 - Default Jumper Settings

The Diagram at Left shows the Default Settings for INPUT 1.

VOX 1 is SWITCHED ON VOX 2 is SWITCHED OFF MUTE 1 is SWITCHED OFF MUTE 2 is SWITCHED OFF

When the INPUT 1 (MIC 1) is activated the VOX 1 BUSS is ON and it will MUTE any Input with the MUTE 1 Setting SWITCHED ON.

INPUT 1 (MIC)

WHITE

RED

250ohm 1.5mV

BALANCED

INPUT 2 (MIC)

NOTE: To change the INPUT Default Settings refer to the appropriate section in this Manual

INPUT 3 (MIC)

G COM HOT G COM HOT G COM HOT

3120 Micbal 01

TWO LEADS UNBALANCED MICROPHONE WIRING

VOX - MUTE JUMPERS SETTING

OFF

VOX SEND

MIC IN

Input 1 - V1 - 01

MUTE RECEIVE

INPUT 1

AUDIO OUT

OFF

MIC

Lo Z

SW215

JUMPER

SW220

JUMPER

X X

SHIELD

VOX 1 BUSS ACTIVATED

VOX 2 BUSS OFF

JUMPER

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

INPUT 1 - Default Jumper Settings

The Diagram at Left shows the Default Settings for INPUT 1.

VOX 1 is SWITCHED ON VOX 2 is SWITCHED OFF MUTE 1 is SWITCHED OFF MUTE 2 is SWITCHED OFF

When the INPUT 1 (MIC 1) is activated the VOX 1 BUSS is ON and it will MUTE any Input with the MUTE 1 Setting SWITCHED ON.

250ohm 1.5mV

INPUT 1 (MIC)

HOT LEAD

BALANCED

INPUT 2 (MIC)

NOTE: To change the INPUT Default Settings refer to the appropriate section in this Manual

INPUT 3 (MIC)

G COM HOT G COM HOT G COM HOT

3120 Micunbal 01

PAGE 11

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

INSTALLATION AND WIRING

USING A PUSH-TO-TALK DESK BASE MICROPHONE

Microphone paging and precedence over AUX 1 or AUX 2 channels may be accomplished by using a Desk Base or a Gooseneck Microphone.Wire the Microphone output leads to the MIC input terminals as per Fig. 11A.

MUTING: The Amplifier is equipped with two independent Muting Circuits:

z Direct Muting by shorting the MUTE Terminals

Automatic Muting with VOX - Voice Activated Muting

For additional information on the Muting operation refer to the Muting Functions section of this Manual.

WIRING

Fig. 11A - Input 1 and Muting Terminals

Wire the Desk Base Microphone leads to the Microphone Input terminal strip as per diagram in Fig 11A. Check Microphone instructions and connect HOT LEAD (B) to Ter minal HOT, COMMON LEAD (A) to Ter minal COM and SHIELD LEAD to Terminal G. Connect Muting Switch to Ter minals MUTE 1 or MUTE 2 and G as shown.

DO NOT GROUND THE MICROPHONE CABLE SHIELD TO THE CHASSIS OF THE AMPLIFIER

b50side

Push to Talk Key

Fig. 11 - Desk Base Microphone

INPUT 1 - USING A DESK BASE MICROPHONE

MUTING - PRIORITY SETTINGS

MUTING INPUT 4/AUX 1 (MUSIC INPUT)

T o m ute Input 4/A UX 1 (Music Input) when P aging from MIC 1, set INPUT 4/AUX 1 MUTE 1 JUMPER to ON Position. Each time MIC 1 is activated the Program on Input 4/AUX 1 is automatically muted by the VOX.

Direct Muting is provided by the Desk Base Muting Switch wired as per diagram in Fig. 11A. If Auto-Mute (VOX) is desired follow instructions below.The Desk Base Muting Switch can be omitted.

CAUTION:

TO PREVENT POSSIBLE DAMAGE TO SPEAKERS OR THE AMPLIFIER ALL INPUT CONNECTIONS MUST BE MADE WITH THE AMPLIFIER POWER OFF.

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

Push to Talk Key

b50side

VOX - MUTE JUMPERS SETTING

VOX SEND

MIC IN

Push to Talk Key

MUTE RECEIVE

Connect Desk Base or Gooseneck Microphone as per diagram below. Connect Muting Switch to MUTE 1 or MUTE 2 and G Terminals. If using the VOX system the muting switch is unnecessary.

INPUT 1

DESK BASE/GOOSENECK MICROPHONE WITH MUTING SWITCH

INPUT 1 - Default Jumper Settings

The Diagram at Left shows the Default Settings for INPUT 1.

VOX 1 is SWITCHED ON VOX 2 is SWITCHED OFF MUTE 1 is SWITCHED OFF MUTE 2 is SWITCHED OFF

When the INPUT 1 (MIC 1) is activated the VOX 1 BUSS is ON and it will MUTE any Input with the MUTE 1 Setting SWITCHED ON.

250ohm 1.5mV

BALANCED

INPUT 2 (MIC)

NOTE: To change the INPUT Default Settings refer to the appropriate section in this Manual

OFF

AUDIO OUT

OFF

X X

SW215

VOX 1 BUSS ACTIVATED

JUMPER

VOX 2 BUSS OFF

JUMPER

SW220

JUMPER

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

MIC

Lo Z

MUTING SWITCH

MUTE 2

GROUND

GM2

SHIELD

MASTER REMOTE

MUTE 1

VOLUME

M1 RVC

RVC

INPUT 1 (MIC)

INPUT 3 (MIC)

G COM HOT G COM HOT G COM HOT

3120 Micbase 01

PAGE 12

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

INPUT CONNECTIONS

CONFIGURATION TABLES

CONDENSER AND ELECTRET TYPE MICROPHONES

Condenser and Electret Microphones require a DC Operating Voltage. The Amplifier provides this operating voltage or Phantom Power selectively on Inputs.1-2-3-4-5.

Prior to selecting the Condenser or Electret Microphone be sure that the Operating Voltage and Output Impedance of the device match the Input characteristics of the Amplifier listed below.

Phantom Power = 18 Volt DC Input Impedance = 250 to 600 ohm

ACCESS TO PHANTOM POWER SELECTORS

1) Remove Power Cord from AC Outlet.

2) Remove the three screws on each side of the Amplifier.

3) Lift Cover and carefully slide Cover out towards the rear.

4) Jumpers are located on the Main Printed Circuit Board.

Fig. 12 - Balanced Condenser/Electret Microphone Wiring - Configuration Tables

THE FOLLOWING INSTRUCTIONS REQUIRE THE REMOVAL OF THE AMPLIFIER PROTECTIVE COVER AND ARE PROVIDED FOR USE BY QUALIFIED PERSONNEL ONLY. TO AVOID THE RISK OF ELECTRICAL SHOCK DO NO T PERFORM ANY INSTALLA TION OR SERVICING UNLESS YOU ARE QUALIFIED TO DO SO. REFER INSTALLATION OR SERVICING TO QUALIFIED PERSONNEL.

CAUTION ! REMOVAL OF THE AMPLIFIER COVER PRESENTS AN ELECTRICAL SHOCK HAZARD

ALWAYS REMOVE THE POWER CORD FROM THE AC WALL OUTLET

CONDENSER AND ELECTRET MICROPHONES

WIRING

PHANTOM POWER SELECTOR JUMPER

By following the Main Printed Board Layout locate the Selector Jumpers with the ID No.as indicated on the Table below.

Reset the Phantom Pow er Jumpers for INPUT 1 - 2 or 3 to the ON position as desired. Lift the Mini Jumper out of the socket pins and re-position to the ON position. Make sure the Jumper is lined up with the socket pins.

INPUT 4 and 5 CONFIGURED AS MIC INPUTS If INPUT 4 and INPUT5 need to be configured as Microphone Inputs, reset the Phantom Power Jumpers as well as the Switches provided for the two Inputs as indicated in the Table below.

PHANTOM POWER SELECTORS

CONDENSER/ELECTRET MICROPHONE

Carefully follow the wiring instruction packed with the Microphone used. Attach the microphone leads to the terminal strip as per diagram per Fig. below.

DO NOT GROUND THE MICROPHONE CABLE SHIELD TO THE CHASSIS OF THE AMPLIFIER

DIGITAL MUSIC AMPLIFIERS

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC SERIES

BALANCED CONDENSER/ELECTRET MICROPHONE WIRING

MIC INPUTS PHANTOM POWER JUMPER SETTING

WHEN USING ELECTRET MICROPHONES

INPUT 1

JUMPER

OFF

SW201

INPUT 2

JUMPER

OFF

SW202

INPUT 3

JUMPER

OFF

SW203

INPUT 4

JUMPER

(When set as MIC 4)

OFF

SW204

INPUT 5

JUMPER

(When set as MIC 5)

OFF

SW207

SHIELD

MIC

Lo Z

INPUT 4 - 5 SWITCH SETTINGS WHEN

CONFIGURING AS MICROPHONE INPUT

Input Switch No. Setting

INPUT 4 SW228 MIC 4 INPUT 5 SW208 MIC 5 INPUT 5 SW229 MIC 5

INPUT 1 (MIC)

-0 +18V +18V

HOT LEAD HOT LEAD

INPUT 4 - 5 DEFAULT

SWITCH SETTINGS

Input Switch No. Setting

INPUT 4 SW228 AUX 1 INPUT 5 SW208 AUX 2 INPUT 5 SW229 AUX 2

250ohm 1.5mV

BALANCED

INPUT 2 (MIC)

INPUT 3 (MIC)

G COM HOT G COM HOT G COM HOT

INPUT 1- 2 - 3 - 4 - 5 DEFAULT

JUMPER SETTINGS

Input Jumper No. Setting

INPUT 1 SW201 OFF INPUT 2 SW202 OFF INPUT 3 SW203 OFF INPUT 4 SW204 OFF INPUT 5 SW207 OFF

3120 Micbal Electret

PAGE 13

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

Fig. 13A - Balanced Telephone Input Wiring

WIRING - The Amplifier is interface ready for the Telephone

line in applications requiring paging from the telephone system. The Telephone line Paging Output (Tip and Ring) can be directly connected to the TEL input and to the HOT and COM as shown in the wiring diagram Fig. 12A .

CABLE - Use a two conductor twisted wire. NOTE: The Telephone Paging Input is a Transformer

Balanced 600 ohm input.

DO NOT GROUND THE TIP OR RING WIRE TO THE CHASSIS OF THE AMPLIFIER

OUTPUT LEVEL CONTROL - Use TEL OUTPUT LEVEL

Control located on the Rear panel. After wiring adjust control for the desired output level.

VOICE ACTIVATED MUTING (VOX) - Muting of the AUX 1 channel (music muting) during Paging is automatic via the Voice Activated Muting System. No contact closure for the Muting Circuit is required from the Telephone system. For additional information on the Muting operation refer to the Muting Functions section of this Manual.

PHONE PAGING PRIORITY OVER MICROPHONES -

Priority over any Microphone Input may be accomplished b y setting the MIC Inputs MUTE Jumpers.

INSTALLATION AND WIRING

Fig. 13 - Connecting to the Telephone Paging KSU

CAUTION:

TO PREVENT POSSIBLE DAMAGE TO SPEAKERS OR THE AMPLIFIER ALL INPUT CONNECTIONS MUST BE MADE

WITH THE AMPLIFIER OFF (POWER OFF).

P A GING FROM THE TELEPHONE SYSTEM

TELEPHONE SYSTEM PAGING WIRING

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

DMS

DIGITAL MUSIC AMPLIFIER

DIGITAL MUSIC SERIES

100 100 100 100 100 100 +10-10 +10-10

INPUT 1 INPUT 2 INPUT 3 INPUT 4/AUX 1 INPUT 5/AUX 2 BASS TREBLEMODULE

DMS Amplifier

PROFESSIONAL AUDIO & SOUND

OUTPUT LEVEL

PEAK

TEL

POWER

Key Service Unit

KSU

Telephone

telpagin

BALANCED TELEPHONE PA GING WIRING

VOX - MUTE JUMPERS SETTING

SW214

OFF

VOX SEND

TEL IN

MUTE RECEIVE

TEL INPUT

Telephone System Paging Output

JUMPER

PAGING OUT

SW216

JUMPER

OFF

X X

VOX 1 BUSS ACTIVATED

VOX 2 BUSS OFF

JUMPER

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

TEL INPUT - Default Jumper Settings

The Diagram at Left shows the Default Settings for TEL INPUT.

VOX 1 is SWITCHED ON VOX 2 is SWITCHED OFF MUTE 1 is SWITCHED OFF MUTE 2 is SWITCHED OFF

When the TEL INPUT (PHONE) is activated the VOX 1 BUSS is ON and it will MUTE any Input with the MUTE 1 Setting SWITCHED ON.

TEL

G COM HOT

600 ohm 100 mV

BALANCED

NOTE: To change the

RING

INPUT Default Settings refer to the appropriate section in this Manual

TIP

3120 T elpaging 01

INPUT 4 SET AS AUX 1 (Reference. 19)

The AUX 1 input is provided for high level program source. The output from a Satellite Receiver, Tuner, Tape Cassette Deck, CD Player or other high level program source may be directly connected to this input.

AUX 1 SENSITIVITY ATTENUATOR (Reference. 18)

The AUX 1 Input is equipped with a Sensitivity Attenuator that allows the interface of the Input with Devices having a wide range of Output Levels.

TYPICAL OUTPUT LEVEL OF MUSIC DEVICES: Satellite Receivers = 1 to 5 Volt Digital T uners/Receivers = 100 to 300 Mv CD Players/Changers = 2 to 3 Volt Tape Decks = 500 to 700 Mv

By adjusting the Input Sensitivity to the level that matches the device used the correct interface with the Amplifier is achieved resulting in lower overall distortion and better frequency response characteristics.

SETTING THE AUX 1 INPUT ATTENUATOR

Connect a Music Source to the Amplifier. Turn Attenuator (rear panel) fully counterclockwise. Turn INPUT 4 Front Panel Control to midway. Switch Amplifier and Music Source ON. Turn Attenuator Control (rear panel) until desired Output Level is achieved. Adjust INPUT 4 Front Panel Level Control Up-Down as desired.

STEREO SUMMING

Most Music Source Devices provide a Stereo Output. Accordingly the Amplifier is equipped with two Jacks f or the AUX 1 Input (L and R). The two Inputs are internally buffered and electronically mixed to Mono. This system ensures that the Music Device is properly loaded and that the Stereo Signals are correctly summed (L+R) to Mono without distortion.

CABLE

To connect the music source devices to the AUX 1 Input use two single conductor shielded audio cable terminated in a single prong phono plug on both ends.

Fig. 14 - Rear Panel AUX 1 Input Diagram

AUX 1

AUX 1 INPUT MUTING

Fig. 14A - Stereo Summing and AUX 1 Input Attenuator

MUTING - WHEN MIC 1 OR THE TEL IN ARE ACTI-

VATED THE VOX 1 BUSS IS SWITCHED-ON AND THE SIGNAL PRESENT ON THE MUTE 1 BUSS WILL MUTE THE MUSIC FROM AUX 1.

SETTING INPUT 4 AS AUX 1 INPUT 4/AUX 1 DEFAULT SETTING

JUMPERS/SWITCH NO. FACTORY SETTING SW212 - VOX JUMPER = OFF

SW217 - MUTE JUMPER = M 1 SW228 - AUX1-MIC4 SWITCH = AUX 1

PAGE 14

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

INSTALLATION AND WIRING

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DEFAULT JUMPERS AND SWITCH SETTING

SW212 = OFF SW217 = M 1 SW228 = AUX 1

MUSIC

AUX 1 - MIC 4 SWITCH

SW228

AUX 1 MIC 4

AUX 1

ATTENUATOR

3120 Aux1 01

INPUT - 4 (AUX1)

47 kohm 100 mV

INPUT 4

AUX 1

Input 1-4 - V1 - 01

INPUT-5(AUX2)

47kohm 100mV

MUSIC OUTPUT

MUSIC OUT

(AUX2)

ATTENUATOR

INPUT 5

MIC-AUX2

BY INTERNAL

SWITCH

OFF

JUMPER

VOX 1 BUSS OFF

X X

VOX 2 BUSS OFF

SW212

WHEN MIC 1 IS ACTIVATED THE VOX 1 BUSS IS SWITCHED-ON AND THE SIGNAL PRESENT ON THE MUTE 1 BUSS WILL MUTE THE MUSIC FROM INPUT 4/AUX 1

SW217

MUTE 1 BUSS ON

JUMPER

MUTE 2 BUSS OFF

SATELLITE RECEIVER

AM/FM TUNER

CD PLAYER

TAPE DECK

paso

TRACK 01

DIGITAL MUSIC SERIES

INPUT - 4 (AUX1)

47 kohm 100 mV

AUX 1

ATTENUATOR

3120 Stereo Summ

PAGE 15

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

INPUT 5 SET AS AUX 2 (Reference. 20)

The AUX 2 input is provided for high level program source. The output from a Jukebox, Tuner, Tape Cassette Deck, CD Player or other high level program source may be directly connected to this input.

AUX 2 SENSITIVITY ATTENUATOR (Reference. 21)

The AUX 2 Input is equipped with a Sensitivity Attenuator that allows the interface of the Input with Devices having a wide range of Output Levels.

TYPICAL OUTPUT LEVEL OF MUSIC DEVICES: Satellite Receivers = 1 to 5 Volt Digital T uners/Receivers = 100 to 300 Mv CD Players/Changers = 2 to 3 Volt Tape Decks = 500 to 700 Mv

SETTING THE AUX 2 INPUT ATTENUATOR

Connect a Music Source to the Amplifier. Turn Attenuator (rear panel) fully counterclockwise. Turn INPUT 5 Front Panel Control to midway. Switch Amplifier and Music Source ON. Turn Attenuator Control (rear panel) until desired Output Level is achieved. Adjust INPUT 5 Front Panel Level Control Up-Down as desired.

STEREO SUMMING

CABLE

To connect the music source devices to the AUX 1 Input use two single conductor shielded audio cable terminated in a single prong phono plug on both ends.

Fig. 15 - Rear Panel AUX 2 Input Diagram

AUX 2

AUX 2 INPUT MUTING

Fig. 15A - Stereo Summing and AUX 2 Input Attenuator

MUTING - WHEN MIC 1 OR THE TEL IN ARE ACTI-

VATED THE VOX 1 BUSS IS SWITCHED-ON AND THE SIGNAL PRESENT ON THE MUTE 1 BUSS WILL MUTE THE MUSIC FROM AUX 2.

SETTING INPUT 5 AS AUX 2 INPUT 5/AUX 2 DEFAULT SETTING

JUMPERS/SWITCH NO. FACTORY SETTING SW213 - VOX JUMPER = OFF

SW223 - MUTE JUMPER = M 1 SW208 - AUX 2-MIC 5 SWITCH = AUX 2 SW229 - AUX 2-MIC 5 SWITCH = AUX 2

INSTALLATION AND WIRING

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DEFAULT JUMPERS AND SWITCH SETTING

SW213 = OFF SW223 = M 1 SW208 = AUX 2 SW229 = AUX 2

MUSIC

AUX 2 - MIC 5 SWITCH

SW208 and SW229

AUX 2 MIC 5

SET TO AUX 2

INPUT - 4 (AUX1)

47 kohm 100 mV

AUX 1

ATTENUATOR

3120 Aux2 01

INPUT 5

AUX 2

Input 1-4 - V1 - 01

INPUT 5 (AUX 2) 47 Kohm 100 mV

(AUX 2)

ATTENUATOR

INPUT 5

MIC-AUX2

BY INTERNAL

SWITCH

MUSIC OUTPUT

JUMPER

OFF

SW213

MUSIC OUT

SW223

OFF

JUMPER

VOX 1 BUSS OFF

X X

VOX 2 BUSS OFF

WHEN MIC 1 IS ACTIVATED THE VOX 1 BUSS IS SWITCHED-ON AND THE SIGNAL PRESENT ON THE MUTE 1 BUSS WILL MUTE THE MUSIC FROM INPUT 5/AUX 2

MUTE 1 BUSS ON

MUTE 2 BUSS OFF

SATELLITE RECEIVER

paso

AM/FM TUNER

TRACK 01

CD PLAYER

TAPE DECK

DIGITAL MUSIC SERIES

3120 Stereo Summ 01

INPUT 5 (AUX 2) 47 Kohm 100 mV

ATTENUATOR

(AUX 2)

INPUT 5

MIC-AUX2

PAGE 16

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

ADDRESSABLE DUAL VOX SYSTEM

DUAL VOX - VOICE ACTIVATED MUTING - The Amplifier is equipped with a DUAL noiseless, fast acting Logic VOX Switching System. When any of the INPUTS are activated and a Signal is present on a given INPUT and either VOX 1 or VOX 2 or BOTH are Switched-ON (using internal Jumpers) then the MUTE 1 or MUTE 2 BUSS or BOTH are ACTIVE. If any of the INPUTS have the MUTE 1 or MUTE 2 Switched-ON (by Internal Jumpers) then the INPUT (or INPUTS) will be MUTED according to the Jumpers Setting. Once the SIGNAL-ON on the ACTIVE INPUT is terminated the normal functions are automatically restored on all muted inputs.

ACCESS T O VO X AND MUTE JUMPERS

REFER TO JUMPERS AND SWITCHES INTERNAL ACCESS.

CAUTION:PRIOR TO PERFORMING THE ABOVE OPERATION BE SURE TO FOLLOW THE SAFETY NOTES REFERRING TO THE REMOVAL OF THE AMPLIFIER COVER.

Fig. 16 - Rear Panel VOX 1 and VOX 2 Sensitivity Control

and MUTE 2 Delay Control

VOX - VOICE ACTIVATED MUTING

VOX SENSITIVITY CONTROLS

VOX SENSITIVITY ADJUSTMENT

1) Turn all Front Panel Input Level Controls to 0.

2) Turn VOX Sensitivity Control counterclockwise until it stops.

3) Connect a Signal Source (Microphone, Telephone or Music) to the respective Input Terminals (For connection details refer to the appropriate section in this Manual).

4) While talking from a Paging Source (Microphone or Telephone) or Playing Music rotate the INPUT LEVEL CONTROLS (Front Panel) until the desired output level is achieved.

5) While talking from a Paging Source (Microphone or Telephone) or Playing Music, turn the Sensitivity Control (VOX 1 or VOX 2) slowly clockwise until the Muting (MUTE 1 or MUTE 2) is activated.

VOX JUMPERS DEFAULT SETTING TABLE

SW210 INPUT 2 - VOX1 - VOX2 - OFF OFF SW211 INPUT 3 - VOX1 - VOX2 - OFF OFF SW212 INPUT 4 - VOX1 - VOX2 - OFF OFF SW213 INPUT 5 - VOX1 - VOX2 - OFF OFF SW214 TEL IN - VOX1 - VOX2 - OFF V1 SW215 INPUT 1 - VOX1 - VOX2 - OFF V1 SW221 MODULE - VOX1 - VOX2 - OFF OFF

JUMPER JUMPER FUNCTION FACTORY FACTORY

ID NO. REFERENCE DESCRIPTION SETTING SETTING

MAIN PCB JUMPERS

VOX SENSITIVITY CONTROLS

VOX 1 AND VOX 2 SENSITIVITY CONTROLS

The VOX 1 and VOX 2 Sensitivity Controls set the sensitivity level at which point the VOX 1 and VOX 2 are respectively engaged during INPUT ACTIV ATION.The VO X Sensitivity Controls are located on the Amplifier Rear Panel.

VOX 1 SENSITIVITY CONTROL = Reference 33 VOX 2 SENSITIVITY CONTROL = Reference 32

VOX SENSITIVITY ADJUSTMENT

INSTALLATION AND WIRING

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

VOX-2 MUTE-2

VOX-1

SENS

DELAY

313233

DMS3120 Vox Sens 01

PAGE 17

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

ADDRESSABLE DUAL MUTING SYSTEM

DIRECT MUTING - Direct Muting may be accomplished by shorting the MUTE 1 and MUTE 2 Terminals to the G Terminal through an external switch.Each time the Muting Switch is closed the corresponding MUTE BUSS is activated.

Fig. 17 - Direct Muting Terminals and Diagram

DIRECT MUTING

WIRING

Fig. 17B - M 1 Function Timing Diagram

MUTING TIMING - The MUTING is preset f or -60 db Attenuation.

When MUTE 1 or 2 are activated the MUTE BUSS is instantaneously Switched-ON. When the Muting is deactivated the program source is gradually restored.

MUTE 1 (M1) = TIMING PRESET 2-3 SECONDS MUTE 2 (M2) = TIMING ADJUSTABLE 3-30 SECONDS MUTE 2 DELA Y = USE REAR PANEL CONTROL Reference 31

INSTALLATION AND WIRING

MUTE JUMPERS DEFAULT SETTING TABLE

SW206 VOX RELAY - MUTE 1 - MUTE 2 M1 SW216 TEL IN - MUTE 1 - MUTE 2 - OFF OFF SW217 INPUT 4/AUX 1 - MUTE 1 - MUTE 2 - OFF M1 SW218 INPUT 3 - MUTE 1 - MUTE 2 - OFF OFF SW219 INPUT 2 - MUTE 1 - MUTE 2 - OFF OFF SW220 INPUT 1 - MUTE 1 - MUTE 2 - OFF OFF SW222 MODULE - MUTE 1 - MUTE 2 - OFF OFF SW223 INPUT 5/AUX 2 - MUTE 1 - MUTE 2 - OFF M1 SW227 CHIME TRIGGER - MUTE 1 - MUTE 2 M1

JUMPER JUMPER FUNCTION FACTORY FACTORY

ID NO. REFERENCE DESCRIPTION SETTING SETTING

MAIN PCB JUMPERS

DUAL MUTING SYSTEM - The Amplifier is equipped with a DUAL

noiseless, fast acting Logic MUTING Switching System.When any of the INPUTS are activated and a Signal is present on a given INPUT and either VOX 1 or VOX 2 or BOTH are Switched-ON (using internal Jumpers) then the MUTE 1 or MUTE 2 BUSS or BOTH are ACTIVE. If any of the INPUTS have the MUTE 1 or MUTE 2 Switched-ON (by Internal Jumpers) then the INPUT (or INPUTS) will be MUTED according to the Jumpers Setting. Once the SIGNAL-ON on the ACTIVE INPUT is terminated the normal functions are automatically restored on all muted inputs.

ACCESS T O MUTE JUMPERS

REFER TO JUMPERS AND SWITCHES INTERNAL ACCESS. CAUTION: PRIOR TO PERFORMING THE ABOVE OPERATION

BE SURE TO FOLLOW THE SAFETY NOTES REFERRING TO THE REMOVAL OF THE AMPLIFIER COVER.

Fig. 17C - M 2 Function Timing Diagram

MUTE 2 DELAY - The M 2 Delay can be adjusted by using the

MUTE 2 DELAY CONTROL

on the rear panel (reference 31).

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

MASTER REMOTE

MUTE 1

VOLUME

MUTE 2

MUTE-2

DELAY

GROUND

GM2

M1 RVC

RVC

MUTING SWITCH M 2

3120 M1 - M2 01

MUTING SWITCH M 1

Signal

Level

DMS mutfunct 01

MUTE 1

Program

Attenuation

60 dB

Terminals

shorted

Program

2-3

gradually

sec.

restored

Mute terminals

opened

time

Signal

Level

DMS mutfunct 02

MUTE 2

Program

Attenuation

60 dB

Terminals

shorted

Adjustable

from

3 to 30

seconds

Mute terminals

opened

Program

gradually

restored

time

PAGE 18

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

INSTALLATION AND WIRING

INPUT 1 (MIC 1) UNMUTING FUNCTION

The Input 1 (MIC 1) can be preset to be normally MUTED (INPUT OFF) when the JUMPER SW205 - MIC 1 UNMUTE - IS SET TO

THE ON POSITION. The MIC 1 is SWITCHED-ON when the UNMUTE and G Terminals are shorted by a Switch Contact

Closure.This function allows for a multi zone installation using two or more Amplifiers and a single Microphone and Zone Switches. When the Jumper SW205 is set to the ON Position the Microphone Input is OFF and it is turned ON when the UNMUTE and the G terminals are closed by a switch.

JUMPER NO. FUNCTION POSITION SET SW205 MIC 1 Muted ON

If the Jumper requires resetting follow the instruction below.

ACCESS TO UNMUTING JUMPER

1) Remove Power Cord from AC Outlet.

2) Remove the three screws on each side of the Amplifier securing the Top Cover to the Chassis.

3) Lift Cover and carefully and slide Cover out towards the rear.

4) On the Main Amplifier Printed Board locate the SW205 MIC 1 UNMUTE Jumper Set.

5) Set Jumper to the ON position.

Fig. 18 - Microphone and Zone Unmuting Diagram

THE FOLLOWING INSTRUCTIONS REQUIRE THE REMOVAL OF THE AMPLIFIER PROTECTIVE COVER AND ARE PROVIDED FOR USE BY QUALIFIED PERSONNEL ONLY. TO AVOID THE RISK OF ELECTRICAL SHOCK DO NOT PERFORM ANY INSTALLATION OR SERVICING UNLESS YOU ARE QUALIFIED TO DO SO.

CAUTION !

REMOVAL OF THE AMPLIFIER COVER PRESENTS AN ELECTRICAL SHOCK HAZARD

ALWAYS REMOVE THE POWER CORD FROM THE AC WALL OUTLET

DIRECT UNMUTING

WIRING

Fig. 18A - 2 - Zone System Jumper Settings

Fig. 18B - 2 - Zone Switching Panel

INPUT 1 (MIC 1) UNMUTING FUNCTION

The Fig. at right shows a typical 2 Zone Switching Panel. Use SPST Momentary Contact Switches. See complete 2 - Zone Wiring Diagram provided in this Manual.

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

MUTE 2

M1 RVC

MASTER REMOTE

MUTE 1

VOLUME

RVC

SHIELD

2 - ZONE

PAGING SELECTORS

Connect Paging Microphone as per diagram below (reference 30). Connect Zone Unmuting Switch to UNMUTE (reference 9) and G Terminals. The VOX (if ON) feature will automatically mute the Music

250ohm 1.5mV

INPUT 1 (MIC)

BALANCED

INPUT 2 (MIC)

G COM HOT G COM HOT

A = Common B = Hot

3120 Unmute 01

UNMUTE - VOX AND MUTE JUMPER

SETTINGS ON AMPLIFIERS 1 & 2

MICROPHONE WITH UNMUTING ZONE SWITCH

GROUND

UNMUTE

MIC1 G M2

ZONE UNMUTING SWITCH

MIC

Lo Z

INPUT 1

OFF

V1 V2

MIC 1

JUMPER

VOX 1 ON

UNMUTE

MIC 1

JUMPER

SW205

OFF

SW215

3120 Unmute Jump Set

OFF

INPUT 4

M1 M2

SW217

AUX 1

JUMPER

MUTE 1 ON

TO AMP 1

TO AMP 2

3120 2 Zone Diagram 01

TO MIC INPUT

SPST ZONE

SWITCHES

ZONE 1

ZONE 2

PAGING MICROPHONE

PAGE 19

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

INSTALLATION AND WIRING

OPERATION - A 2 - Zone Paging Wiring Diagram Application is provided.The Paging Microphone is connected in parallel to all the Microphone Inputs.Two

Independent SPST Switches are provided for the Paging Zone Selection. MUSIC - The MUSIC SOURCE (Satellite Receiver) is cascade connected to the

two Amplifiers.ZONE PAGING - When one or more Zone Switches are activated the UNMUTE Function OPENS the Microphone Channel on the Amplifier

selected and the MICROPHONE is active for the PAGING. Simultaneously the MUSIC is MUTED ONLY ON THE ZONE (OR ZONES) SELECTED.

Independent MUSIC SOURCE may be provided to each of the Amplifiers if required.MOH - MUSIC ON HOLD is available from each of the Amplifiers used.

The MOH source maybe selected from either the AUX 1, AUX 2 or the MODULE Input and is immune to Paging or the MUTE/UNMUTE Function.

2 ZONE PAGING AND MUSIC WIRING DIAGRAM

Fig. 19 - 2 Zone Paging and Music System

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

SELECTORS

2 ZONE PAGING

Paging Microphone can be

Unswitched and always ON

PAGING MICROPHONE

SATELLITE RECEIVER

MUSIC SOURCE LINE

UNMUTE

GROUND

47kohm 100mV

INPUT-5(AUX2)

INPUT-4(AUX1)

47kohm 100mV

MIX

BUSS

PRE EQ

SUB OUT

PRE

OUT

30TJ

AUDIO

LISTED

EQUIPMENT

COMMERCIAL

CUS

RVC

MASTER

REMOTE

VOLUME MUTE 1

M1 RVC

MUTE 2

GROUND

UNMUTE

MIC1 G M2

24V DC

250 mA

VOX RELAY

NC C NO

ZONE 2

(AUX2)

ATTENUATOR

(AUX1)

ATTENUATOR

EQ LINK

LEVEL

MUSIC OUTPUT

MODULE

STANDARD

PORT ACCEPTS

INPUT 5

MIC-AUX 2

BY INTERNAL

OFF

TONE

BYPASS

AUX2

600

INPUT 4

LINE OUT

SUB OUT

POST EQ

POWER

EQ LINK

IN OUT

DO NOT OPEN

CAUTION

RISK OF ELECTRIC SHOCK

WARNING: THIS APPLIANCE

120 W RMS

DMS3120

DIGITAL MUSIC AMPLIFIER

PROFESSIONAL AUDIO & SOUND

POWER RATING

CAUTION: REMOVE

TEL OUTPUT

SWITCH

TEL

G COM HOT

47Kohm 100 mV

INPUT5 (MIC-AUX2)

VOLUME

REMOTE

G COM HOT RVC RVC G COM HOT G COM HOT G COM HOT G COM HOT

INPUT 4 (MIC) INPUT 3 (MIC)

INPUT 2 (MIC)

MUST BE EARTHED

INPUT 1 (MIC)

850 VA

117V 60 HZ

VOX-2 MUTE-2

SUPPLY VOLT A GE

POWER CONSUMPTION

VOX-1

POWER CORD FROM

AC OUTLET PRIOR TO

INSTALLING MODULE

LEVEL

DELAY

SENS

600 ohm 100mV

BALANCED

250ohm 1.5mV

SER. NO.

HOT

COMMON

MICROPHONE WIRE

GROUND (SHIELD)

MUSIC SOURCE LINE

25V/70V Speaker

2 Conductor Shielded

UNMUTE

INPUT-5(AUX2)

INPUT-4(AUX1)

MIX

SUB OUT

PRE

LISTED

GROUND

MASTER

MUTE 1 ON

JUMPER

47kohm 100mV

BUSS

PRE EQ

OUT

30TJ

AUDIO

EQUIPMENT

COMMERCIAL

CUS

RVC

REMOTE

VOLUME

MUTE 1

M1 RVC

MUTE 2

GROUND

UNMUTE

MIC1 G M2

24V DC

250 mA

VOX RELAY

NC C NO

ZONE 2

ZONE 1

SPST

SWITCHES

PORT ACCEPTS

(AUX2)

ATTENUATOR

(AUX1)

ATTENUATOR

OFF

EQ LINK

IN OUT

LEVEL

MODULE

STANDARD

CAUTION: REMOVE

POWER CORD FROM

LEVEL

TEL OUTPUT

INPUT 5

SWITCH

MIC-AUX 2

BY INTERNAL

TEL

G COM HOT

TONE

BYPASS

AUX2

47Kohm 100 mV

INPUT5 (MIC-AUX2)

600

INPUT 4

LINE OUT

VOLUME

REMOTE

SUB OUT

POST EQ

G COM HOT RVC RVC G COM HOT G COM HOT G COM HOT G COM HOT

INPUT 4 (MIC) INPUT 3 (MIC)

POWER

EQ LINK

INPUT 2 (MIC)

DO NOT OPEN

CAUTION

RISK OF ELECTRIC SHOCK

MUST BE EARTHED

INPUT 1 (MIC)

WARNING: THIS APPLIANCE

850 VA

120 W RMS

117V 60 HZ

DMS3120

VOX-2 MUTE-2

DIGITAL MUSIC AMPLIFIER

PROFESSIONAL AUDIO & SOUND

POWER RATING

SUPPLY VOLT A GE

POWER CONSUMPTION

VOX-1

AUX 1

INPUT 4

MIC 1

UNMUTE

JUMPERS SETTING

ON AMPLIFIERS 1 & 2

MIC 1

INPUT 1

AC OUTLET PRIOR TO

INSTALLING MODULE

3120 2 Zone Diagram

600 ohm 100mV

BALANCED

250ohm 1.5mV

DELAY

SENS

SER. NO.

OFF

JUMPER

OFF

SW205

JUMPER

SW217

VOX 1 ON

SW215

25V/70V Speaker

0 8

ZONE 2

1 WATT

0 8

ZONE 1

0 600

AFIN DE REDUIRE LE RISQUE

LEVEL

ZONE 1

D'INCENDIE REMPLACER SEUL PAR UN

FUSIBLE DE MEME TYPE.

ATTENTION:

CAUTION: TO REDUCE THE

RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE

FUSE.

1 WATT

ATTENTION: POUR REDUIRLES RISQUES D' INCENDIE

OU DE CHOC ELECTRIQUE, NE PAS EXPOSER A LA PLUIE

OU L' HUMIDITE, NE PAS ENLEVER LE COUVERCLE. AUCUN

REGLAGE A L' INTERIEUR. POUR REPARATION CONSULTER

UNE PERSONNE QUALIFIEE

BALANCED

MOH OUT

CAUTION: TO REDUCE THE RISK OF FIRE OR

SHOCK DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE. DO NOT REMOVE COVER.

THERE ARE NO USER SERVICEABLE PARTS

117V 500W MAX

SPEAKER OUTPUT

COM 8 25V 70V

GROUND

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

5A 250V

LINE FUSE

UNSWITCHED

117V 60HZ

ZONE 1

25V/70V Speaker 25V/70V Speaker

0 8

ZONE 2

1 WATT

0 8

1 WATT

ZONE 1

0 600

MOH OUT

AFIN DE REDUIRE LE RISQUE

LEVEL

ZONE 1

D'INCENDIE REMPLACER SEUL PAR UN

FUSIBLE DE MEME TYPE.

ATTENTION:

CAUTION: TO REDUCE THE

RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE

FUSE.

ATTENTION: POUR REDUIRLES RISQUES D' INCENDIE

OU DE CHOC ELECTRIQUE, NE PAS EXPOSER A LA PLUIE

OU L' HUMIDITE, NE PAS ENLEVER LE COUVERCLE. AUCUN

REGLAGE A L' INTERIEUR. POUR REPARATION CONSULTER

UNE PERSONNE QUALIFIEE

COM 8 25V 70V

BALANCED

GROUND

CAUTION: TO REDUCE THE RISK OF FIRE OR

SHOCK DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE. DO NOT REMOVE COVER.

THERE ARE NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

LINE FUSE

UNSWITCHED

117V 500W MAX

117V 60HZ

SPEAKER OUTPUT

5A 250V

ZONE 2

25V/70V Speaker 25V/70V Speaker

PAGE 20

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

INSTALLATION AND WIRING

CONNECTING TO AN EXTERNAL EQUALIZER

The Amplifier is equipped with an External Equalizer Link to allows the use of an External Equalizer for applications requiring

Frequency Selective Acoustic Correction

. The Amplifier is furnished with the two jacks of the Link bridged by a SELECTOR SWITCH. When the EQ LINK Switch (REFERENCE 12) is the IN position the internal Preamplifier to Amplifier Link (Reference 13) is broken allowing the insertion of an External Equalizer.

INST ALLA TION TIPS

1) Use high quality, short length audio cables and position the Equalizer in close proximity to the Amplifier. Avoid mounting the EQ on top of the Amplifier unless is Rack mounted.

2) Be sure that the Amplifier input controls and the EQ level control are set at zero prior to turning the system On.

3) The Amplifier TONE BY PASS SWITCH (Reference 17) should be set to ON ( linear response position).

4) Carefully adjust the EQ Level Control to avoid distortion caused by excessive signal boost.

5) Follow the instructions supplied with the Equalizer.

WIRING

To connect to an External Equalizer use two (2) single conductor shielded audio cables terminated in a single prong phono plug on both ends.

SET EQ LINK SWITCH TO IN

EXTERNAL EQUALIZER LINK

Fig. 20 - Rear Panel External Equalizer Link Diagram

MIX BUSS BRIDGING

Fig. 20B - Rear Panel Mix Buss Bridging Diagram

BRIDGING TWO AMPLIFIERS

The MIX BUSS (Reference 15) allows two Amplifiers to be bridged and share all inputs.

All signal sources connected to all the inputs are common to the output of both amplifiers. Muting and level controls operate in exactly the same way as if only one amplifier was used.

MIX BUSS BRIDGING

WIRING

CABLE

To bridge two amplifiers or to connect to an external Mixer use a single conductor shielded audio cable terminated in a single prong phono plug on both ends.

SET TONE BY PASS SWITCH TO

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

EXTERNAL EQUALIZER

PRE OUT

EQ LINK

IN OUT

EQ LINK

POWER

To Input of Equalizer

To Output of Equalizer

3120 EQlink

paso

ON OFF

TONE

BYPASS

AMPLIFIER A

MIX

BUSS

LINE OUT

600

3120 Mixbuss

AMPLIFIER B

MIX

BUSS

LINE OUT

600

PAGE 21

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

INSTALLATION AND WIRING

MASTER REMOTE VOLUME

Fig. 21 - Master Remote Volume Control Diagram

REMOTE V OLUME CONTROLS

The Amplifier features two independent Remote Volume Control Capability:The INPUT 4 (AUX 1) Remote Volume (Reference 26) and the MASTER REMOTE VOLUME CONTROL (Reference 11). A 10 K ohm Potentiometer is required for either control. Mount the 10 K Pot on a suitable Wall Plate or any other convenient surface and connect to the Amplifier RVC Terminals as shown in the Diagram. The Paso Model RVC10W Decora Style Remote Volume Control may be used.

INPUT 4 (AUX 1) OPERATION

When connected the Remote Volume adjusts the INPUT 4 (AUX 1) Level only.Usually this input is utilized for the Music Source (Satellite Receiver, CD Player, etc.).

MASTER VOLUME OPERATION

The Control is a Master Volume and controls all the Inputs of the Amplifier with the exception of the MOH and ZONE 1 and ZONE 2 Outputs.

CABLE

To connect the Remote Control to the Amplifier use a two conductor wire not less than A WG 24.While the Remote Volume System uses DC rather than audio caution should be exercised in the la y out of the wire .Always avoid routing next to pow er lines.If the total wire resistance exceeds 3 K ohm the Volume may not go down to zero.

REMOTE VOLUME CONTROL - OPTIONAL ACCESSORY

MODEL RVC10W REMOTE VOLUME CONTROL

Remote Volume Control Potentiometer. Single Gang Decora Style Plate.

SPECIFICATIONS

Control: 10 K ohm High Quality Control. Connection: 6” Two Wire, color coded (Black and Red) Pigtails stripped and tinned. Color Finish: White. Dimensions: Front Plate = 4.5” High, 2.75” Wide. Depth: 0.5”. Mounting Hardware: Supplied.

INPUT 4 (AUX 1) REMOTE VOLUME

Fig. 21B - Input 4 Remote Volume Control Diagram

Fig. 21C - RVC10W Front View Fig. 21D - RVC10W Rear View

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

MASTER

REMOTE V OLUME

CONTROL 10 K ohm

POTENTIOMETER

MASTER REMOTE VOLUME

RVC

INPUT 4 (AUX 1)

REMOTE V OLUME

CONTROL 10 K ohm

POTENTIOMETER

INPUT 4 REMOTE VOLUME

RVC

Paso Remote

Volume Control

3120 Remote Volume

RVC10W

PAGE 22

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

INSTALLATION AND WIRING

MODULE TYPE

The Amplifier accepts Audio Modules having a 6 Contact PCB Derivation.Module mounting panel should be 3” H., 1-3/8” W. (

78 X 35 mm

INSTALLATION

CAUTION: REMOVE POWER CORD FROM AC OUTLET PRIOR TO INSTALLING A MODULE. BE SURE THAT THE MODULE OUTPUT LEVEL CONTROL IS SET AT “0” PRIOR TO THE INST ALLATION.

1) Locate Rear Panel Module Port (Reference 22) and unscre w the two crosshead scre ws holding the cov er and set aside.

2) Reach inside the Amplifier and gently pull-out the Module Blue Ribbon Connector. If the Connector is tied to the chassis remove the Amplifier Top Cover and with a cutter cut the Nylon Tie holding the connector.

NOTE: BE CAREFUL NOT TO CUT THE CONNECTOR WIRE HARNESS.

3) Pull-out the blue-ribbon connector through the port opening (do not pull-out wire har ness excessively).

4) By keeping the connector gold contacts on the left insert the Module PCB contacts into the socket.

5) Push Module through por t opening and secure to rear panel by using the two screws removed with the Module cover.

MODULE INSTALLATION

INSTALLING A MODULE

Fig. 22 - Rear Panel Module Installation Diagram

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

RVC

WARNING: THIS APPLIANCE

MUST BE EARTHED

INPUT 2 (MIC)

Insert into Module Connector

Printed Board Copper Side

LISTED

COMMERCIAL

AUDIO

EQUIPMENT

30TJ

CUS

EQ LINK

IN OUT

EQ LINK

SUB OUT

PRE EQ

SUB OUT POST EQ

MIX

BUSS

LINE OUT

600

INPUT 4 REMOTE VOLUME

Gold

Contact

TONE

BYPASS

AUX2 47Kohm 100 mV INPUT5 (MIC-AUX2)

PRE OUT

POWER

INPUT 4 (MIC) INPUT 3 (MIC) G COM HOT RVC RVC G COM HOT G COM HOT G COM HOT

250ohm 1.5mV

BALANCED

Side

View

INPUT-4(AUX1) 47kohm 100mV

(AUX1)

ATTENUATOR

OFF

Connector

Top

Front View

TEL

G COM HOT

600 ohm 100mV

INPUT-5(AUX2) 47kohm 100mV

(AUX2)

ATTENUATOR

INPUT 5

MIC-AUX 2

BY INTERNAL

SWITCH

TEL OUTPUT

3120 Module Install

LEVEL

Cable from

Amplifier

PORT ACCEPTS

STANDARD

MODULE

CAUTION: REMOVE POWER CORD FROM AC OUTLET PRIOR TO INSTALLING MODULE

Module Bottom

Module Gold

Contacts

PAGE 23

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

INSTALLATION AND WIRING

MODULE CONNECTOR DIAGRAM

Fig. 23 - Module Connector Contacts Diagram

MODULE CONNECTOR DIAGRAM - The above Diagram indicates the function of each of the six contacts of the Module

Connector. The Module Blue Ribbon Connector is attached to a wire harness and left floating beyond the Module Port Cover.The Wire Harness Amplifier End is attached to Connector No.CN201 and plugged into the mating connector on the Main Printed Circuit Board.

MODULE DEFAULT SETTINGS

Fig. 23A - Module VOX - MUTE - INPUT SOURCE Default Settings

MODULE FUNCTIONS - The Module Port accepts a stan-

dard audio Module.When a Module is utilized several functions can be activated by the Jumpers and Switch provided for this Input.

VOX SEND - The SW221 Jumpers Set activates the VOX 1

- VOX 2 SEND or both. When a Signal is present at the Module Output (Contact 4) then the V OX BUSS selected will be active.

MUTE RECEIVE - The SW222 Jumpers Set activates the

MUTE 1 - MUTE 2 RECEIVE or both.When a Signal is present at the MUTE BUSS 1 or MUTE BUSS 2 the MODULE will be MUTED accordingly.

INPUT SOURCE - The SW209 Switch selectes the Input Source for the Module either AUX 1 or AUX 2. The Signal present at either Input will be sent to the MODULE INPUT (Contact 5).

By selecting the proper Setting several functions can be derived from the Module.

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

Connector

6 5 4 3 2 1

MODULE CONNECTOR

Top

Front View

Gold

Contact

PCB

CONNECTOR

CN201

MODULE

3120 Module Schem

6 5 3 4 3 2

Side View

6 5 4 3 2 1

Cable from

Amplifier

DIGITAL MUSIC SERIES

Connector Contacts

6 = + 24V DC 5 = Module Input 4 = Module Output 3 = Ground 2 = Mute Buss 1 1 = Mute Buss 2

MODULE CONNECTOR

Connector

Top

6 5 4 3 2 1

Front

View

3120 Module Functions

Gold

Contact

Side View

PCB

CONNECTOR

6 5 4 3 2 1

Connector Contacts 6 = + 24V DC 5 = Module Input 4 = Module Output 3 = Ground 2 = Mute Buss 1 1 = Mute Buss 2

Cable from

Amplifier

CN201

MODULE

6 5 3 4 3 2

VOX SEND

MODULE OUTPUT

MUTE RECEIVE

MODULE VOX - MUTE

JUMPERS AND INPUT SOURCE

SWITCH DEFAULT SETTING

JUMPER

MODULE INPUT

OFF

VOX 1 BUSS OFF

X X

VOX 2 BUSS OFF

SW221

AUX 1 - AUX 2 SWITCH

SW209

AUX 1 AUX 2

JUMPER

MUTE 1 BUSS OFF

X X

MUTE 2 BUSS OFF

SW222

AUX 1 SOURCE

AUX 2 SOURCE

PAGE 24

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

INSTALLATION AND WIRING

Fig. 24 - Rear Panel View - ZONE 1 - ZONE 2 - MOH Outputs - Source Selectors and Controls

ZONE 1 MOH AND 8 OHM OUTPUTS MOH - ZONE1 & 2 AMPLIFIER FUNCTIONS

MOH AMPLIFIER

a) The MOH Amplifier can receive programs from AUX

1 - AUX 2 and the MODULE.

b) Selection of the input source is by Internal Jumper. c) The ZONE 1 independent 600 Ohm and 8 Ohm

Outputs may be used simultaneously.

d) The MOH 600 ohm Output is Transformer Balanced. e) The Rear Panel ZONE 1 Level Control operates both

the 600 Ohm and 8 Ohm Outputs simultaneously.

MOH AND ZONE 1-2 OPERATION ISSUES

1) Paging from the Microphone Inputs or the Telephone

Input does not effect the MOH/ZONE 1-2 Amplifier.

2) Position of the INPUTS Level Control does not affect the MOH/ZONE 1-2 Amplifier Output Level.

3) P osition of the AUX 1 and AUX 2 ATTENUATOR does not affect the MOH/ZONE 1-2 Amplifier Output Level.

4) Muting activation of M1 or M2 Buss (from Microphones or Telephone) does not effect the Output of the MOH/ZONE 12 Amplifier except if the INPUT SOURCE is set to MODULE and the Module Output is Muted. See Module Settings.

ZONE 1 OUTPUTS

The DMS Amplifier is equipped with two 1 Watt, 8 ohm Amplifiers and a separate 600 ohm MUSIC ON HOLD AMPLIFIER.

600 Ohm MOH - The MOH Output provides a 600 ohm, 1 Volt Transformer Balanced Output (Reference 3).

1 WATT, 8 Ohm - Simultaneously a Second Zone 8 ohm, 1 Watt Output may be utilized to drive up to 4 Speakers (Reference 4).

OUTPUT LEVEL CONTROL - A Level Control for both the 600 ohm Output and the 1 Watt Output is provided (Reference 2)

MOH AND 8 Ohm AMPLIFIER INPUT SOURCE SELECTION

The program source for the Input of the 600 ohm MOH Output and the 8 ohm Output can be selected from either AUX 1 - AUX 2 or the MODULE source. Set the Jumpers Set No.SW 702 to desired position. Default setting is AUX 1.

ZONE 2 OUTPUT 1 WATT, 8 Ohm - A Second Zone 8 ohm, 1 Watt Output may be

utilized to drive up to 4 Speakers (Reference 5). OUTPUT LEVEL CONTROL - A Level Control for the 1 Watt

Output is provided (Reference 6)

ZONE 2 - 8 Ohm AMPLIFIER INPUT SOURCE SELECTION

The program source for the Input the 8 ohm Output can be selected from either AUX 1 - AUX 2 or the MODULE source. Set the Jumpers Set No. SW 701 to desired position. Default setting is AUX 1.

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

MOH - ZONE 1 INPUT SOURCE

DEFAULT JUMPER SETTING

MODULE

AUX 1

AUX 2

CAUTION: TO REDUCE THE RISK OF FIRE, REPLACE ONLY WITH SAME TYPE FUSE.

117V 500W MAX

UNSWITCHED

117V 60HZ

DMS3120 MOH 01

LINE FUSE

ZONE 1 LEVEL

MOH OUT

CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER. THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

5A 250V

BALANCED

GROUND

ZONE 1

0 600

CLASS 2 WIRING ACCEPTABLE

ZONE 2

0 8

1 WA TT

COM 8 25V 70V

SPEAKER OUTPUT

ZONE 2

LEVEL

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIER

POWER RATING SUPPLY V OL T AGE

POWER CONSUMPTION

VOX-1

SENS

SER. NO.

JUMPER

SW702

ZONE 2 INPUT SOURCE

DEFAULT JUMPER SETTING

MODULE

AUX 1

AUX 2

JUMPER

SW701

PAGE 25

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

INSTALLATION AND WIRING

MOH CONNECTIONS

Fig. 25 - Rear Panel MOH Connection Diagram

MOH/ZONE 1 AMPLIFIER SOURCE SELECTOR

MOH AMPLIFIER

An independent 600 ohm, 1 Volt Output, Transformer Balanced MUSIC-ON-HOLD Amplifier is provided. The Input SOURCE of the MOH Amplifier can be selected from either the AUX 1 - AUX 2 or MODULE.

MOH - 600 OHM SYSTEM

Most Phone systems operate on a 600 ohm Input Impedance, if the Impedance required is 600 ohm connect the Amplifier to the Phone System MOH by using the diagram above (Reference 3).

MOH - 8 OHM, 1 WATT SYSTEM

Some older Key Phone systems require a 1 watt Power Output having an Output Impedance of 8 ohm to drive the Music on Hold feature. If the Impedance required is 8 ohm connect the Phone system MOH to the 8 ohm, 1 Watt MOH Output of the Amplifier (Reference 4).

CABLE

Use a cable consisting of a twisted pair of at least AWG 18.Use care in extending the cable and avoid routing near power lines, fluorescent lights and other systems that may generate a disturbing electric field.

SOURCE SELECTOR

Select the Input Source desired by following the instructions at right.

CAUTION: REMOVAL OF THE COVER PRESENTS AN ELECTRICAL SHOCK HAZARD !

MUSIC ON HOLD AMPLIFIER

MOH/ZONE 1 SOURCE SELECTOR

The Source for the MOH/ZONE 1 Amplifier can be selected from either the AUX 1 - AUX 2 or MODULE by setting the JUMPER SET No. SW702 provided for this purpose. Default Setting for this Jumper Set is AUX 1.To change the setting do the following:

ACCESS TO THE MOH/ZONE 1 INPUT SOURCE SETTING

1) Remove Power Cord from AC Outlet.

2) Remove the three screws on each side of the amplifier holding the amplifier cover.

3) Lift Cover and locate the Jumpers Set No SW702 on the MOH Amplifier Board (see Function Switches Jumpers Location Diagram).

4) Set Jumper as required (AUX 1 - AUX 2 or MODULE)

5) Replace protective cover.

LEVEL CONTROL

After the wiring is completed adjust the MOH/ZONE 1 Amplifier Level Control on the rear panel to the desired output level (Reference 2).

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

Telephone

MOH

Input

600

Ohm

Telephone System

KSU

CAUTION: TO REDUCE THE RISK OF FIRE, REPLACE ONLY WITH SAME TYPE FUSE.

117V 500W MAX

UNSWITCHED

117V 60HZ

3120 MOH Zone 1

600 ohm MOH System

AWG 18 TWISTED PAIR

ZONE 1

LEVEL

GROUND

LINE FUSE

5A 250V

MOH OTPUT LEVEL CONTROL

ZONE 1

0 600

MOH OUT

BALANCED

CLASS 2 WIRING ACCEPTABLE

ZONE 2 0 8

0 8

1 WA TT

COM 8 25V 70V

SPEAKER OUTPUT

MOH - ZONE 1

INPUT SOURCE

ZONE 2

LEVEL

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIER

POWER RATING SUPPLY V OL T AGE

POWER CONSUMPTION

VOX-1 SENS

SER. NO.

DEFAULT JUMPER

SETTING

MODULE

AUX 1

AUX 2

JUMPER

SW702

PAGE 26

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

INSTALLATION AND WIRING

USING SPEAKERS FOR ZONE 1 - ZONE 2

Fig. 26 - Rear Panel Zone 1 and 2 Speaker Connection Diagram

ZONE 1 AND 2 OPERATION

The Amplifier is equipped with two independent 1 Watt, 8 ohm Outputs designated ZONE 1 (Reference 4) and ZONE 2 (Reference 5).The Outputs may be utilized to power up to 4 speakers in various combinations as described in the diagrams on the next page. This feature will provide a SECOND and THIRD ZONE (in addition to the main output) with up to 1 Watt of output power and will amplify only the Source from either AUX 1 - AUX 2 or MODULE (see input source selection) and will not be affected by the Paging (from MIC or TEL), VOX or MUTING.

It can be used in any area (up to 1 Watt) where only a Program Source is desired uninterrupted by Paging.

CABLE

Use an AWG 18 jacketed, twisted pair cable.

ZONE 1 AND 2 OPERATION ZONE 1 AND 2 SETTINGS

INPUT SOURCE SELECTOR

Independent JUMPER SETS for ZONE 1 (SW702) and ZONE 2 (SW701) are available to select the Input Source for the two 1 Watt Amplifiers.

DUAL PROGRAM SOURCE CAPABILITY

If desired separate program Sources may be used for ZONE 1 and ZONE 2. EXAMPLE: Use the program source from AUX 1 for ZONE 2 and the program source from AUX 2 for ZONE 2.

Select the Input Source desired by following the instructions in the MOH Amplifier Source Selection section.

LEVEL CONTROL

After the wiring is completed adjust the ZONE 1 (

Reference

2) and ZONE 2 (

Reference

6) Level Controls on the rear

panel to the desired output level.

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

1/4W

OHM

1/4W

MOH - ZONE 1

INPUT SOURCE

DEFAULT JUMPER

SETTING

MODULE

AUX 1

AUX 2

JUMPER

SW702

1/4W

3120 Zone 1&2

OHM

Up to Four 8 ohm Speakers may

OHM

CAUTION: TO REDUCE THE RISK OF FIRE, REPLACE ONLY WITH SAME TYPE FUSE.

117V 500W MAX

UNSWITCHED

117V 60HZ

be Connected

LINE FUSE

5A 250V

ZONE 1 OUTPUT LEVEL CONTROL

4 Speaker System Max. Power Output= 1/4W Each

AWG 18

TWISTED P AIR

ZONE 1

GROUND

0 600

MOH OUT

BALANCED

ZONE 1

LEVEL

ZONE 1

ZONE 2 0 8

0 8

1 WA TT

COM 8 25V 70V

SPEAKER OUTPUT

CLASS 2 WIRING ACCEPTABLE

TWISTED P AIR

ZONE 2

Up to Four 8 ohm Speakers may

ZONE 2 OUTPUT LEVEL CONTROL

AWG 18

be Connected

ZONE 2

LEVEL

DIGITAL MUSIC AMPLIFIER

POWER RATING SUPPLY VOL T A GE POWER CONSUMPTION

VOX-1

SENS

SER. NO.

PROFESSIONAL AUDIO & SOUND

1/4W

OHM

1/4W

ZONE 2

INPUT SOURCE

DEFAULT JUMPER

SETTING

MODULE

AUX 1

JUMPER

SW701

AUX 2

OHM

1/4W

PAGE 27

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

INSTALLATION AND WIRING

Fig 27 - Using one 8 ohm Speaker

Fig 27A - Using two 4 or 8 ohm Speakers

Fig 27B - Using four 8 ohm Speakers

USING A SINGLE 8 OHM SPEAKER WIRING

USING A SINGLE 8 OHM SPEAKER PER ZONE

A single 8 ohm Speaker may be used connected to the ZONE 1 and ZONE 2 1 W att Output.In this configuration up to 1 Watt of Power will be available on each Speaker.

Independent Level Controls are provided.

ZONE 1 - ZONE 2 CONNECTING SPEAKERS

USING TWO 4 OR 8 OHM SPEAKERS WIRING

USING TWO 4 OR 8 OHM SPEAKERS

The Figure at left shows: ZONE 1 with two 4 ohm speakers connected in series, each speaker provides ½ Watt power output (1 Watt Total).

ZONE 2 with two 8 ohm speakers connected in series, each speaker provides ¼ Watt power output (½ Watt Total).

Independent Level Controls are provided.

USING FOUR 8 OHM SPEAKERS WIRING

USING FOUR 8 OHM SPEAKERS PER ZONE

Four 8 ohm Speakers are used and connected to the 1 Watt Output. In this configuration up to 1/4 Watt of Power will be available on each Speaker (1 Watt Total).

Independent Level Controls are provided.

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

Max. Power Output

1 Watt

ZONE 1

LEVEL

3120 MOHspk01

4 ohm 4 ohm

½ W

When using two

4 Ohm Speakers

the maximum Output Power to each Speaker is

½ Watt

ZONE 1

LEVEL

Zone 1 Zone 2

8 Ohm

ZONE 1

0 600

MOH OUT

BALANCED

Zone 1 Zone 2

0 600

ZONE 1

0 8

1 WA TT

½ W

0 8

8 Ohm

ZONE 2 0 8

1 WA TT

¼ W ¼ W

ZONE 2 0 8

8 Ohm

When using two 8 Ohm

Speakers the maximum

Output Power to each

Speaker is ¼ Watt

ZONE 2

LEVEL

8 Ohm

ZONE 2

LEVEL

3120 Mohspk02

MOH OUT

BALANCED

1 WA TT

Maximum Output

Power to each

Speaker is

¼ Watt

ZONE 1

LEVEL

3120 Mohspk03

Zone 1

8 ohm8 ohm

¼ W

¼ W ¼ W

0 600

MOH OUT

BALANCED

¼ W

8 ohm8 ohm

ZONE 1

0 8

1 WA TT

¼ W ¼ W

ZONE 2

0 8

1 WA TT

Zone 2

8 ohm8 ohm

ZONE 2

LEVEL

PAGE 28

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

POWER SUPPLY

The Amplifier provides a 24 Volt - 250 mA DC Regulated Auxiliary Power Supply Output (Reference 8).

CABLE

To connect the Power Supply Output to accessories use a two conductor wire not less than AWG 18.This minimum wire gauge is necessary to minimize potential Voltage Drops in long wire connection applications.For wire resistance refer to Table below.

24 VOLT POWER SUPPLYREGULATED AUXILIARY POWER SUPPLY

Fig. 28 - 24 Volt Power Supply Output Diagram

WIRE GAUGE - RESISTANCE TABLE

WIRE RESISTANCE IN

AWG OHMS per 1000 Ft.

16 4.016 18 6.385 20 10.15 22 16.14 24 25.67 26 40.81

NOTE:

When calculating the Wire Resistance for each run using a two conductor Wire the wire Resistance should be doubled.

EXAMPLE: The Total Resistance of a 1000 Ft. run of a AWG 24 two conductor Wire is:

25.67 X 2= 51.34 Ohm

VOX RELAY

The Amplifier provides a VOX RELAY (Reference 7) with a single pole dual throw set of contacts. Figure A at left shows the contacts when the Relay is not activated.Figure B shows the contacts when the Relay is activated.

The Relay can be configured to activate when either VOX 1 (M1) or VOX 2 (M2) or both (VOX 1 and VOX 2) are activated.

The VOX RELAY will remain engaged for as long as the VOX is active.

SWITCHSET SW206 - The SW206 is defaulted to M1. When VOX 1 is activated the Relay is switched ON. The factory setting can be changed to set the Relay to activate with either VOX 1 - VOX 2 or both.

Both Jumpers (M1 - M2) may be installed.

RELAY CONTACTS RATING

7 AMPERE AT 30 VDC MAXIMUM RATING.

VOX RELAY FUNCTIONSVOX RELAY

Fig. 28A - VOX Relay Output Terminals

INSTALLATION AND WIRING

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

3120 Power Supply Output

VOX RELAY

NC C NO

24V DC

250 mA

VOX NOT ACTIVATED

MUTE 1 BUSS ON

MUTE 2 BUSS OFF

SWITCHSET SW206 DEFAULT SETTING

JUMPER

SW206

VOX ACTIVATED

MUTE 1 BUSS ON

MUTE 2 BUSS OFF

JUMPER

SW206

Q237

D211

Q237

D211

MASTER REMOTE

MUTE 1

VOLUME

MUTE 2

GROUND

UNMUTE

MIC1 G M2

M1 RVC

RVC

VOX RELAY

RL201

VOX RELAY

RL201

COM

VOX RELAY

NC C NO

24V DC 250 mA

GROUND

UNMUTE

MIC1 G M2

MUTE 2

M1 RVC

MASTER REMOTE

MUTE 1

VOLUME

RVC

3120 Vox relay 01

PAGE 29

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

INSTALLING AND USING A BOSE® EQUALIZER MODULE

Fig. 26 - Method 1 Module Wiring Diagram

BOSE® is a Registered Trademark of BOSE Corporation

METHOD 1

EQUALIZING THE PROGRAM ONL Y

BY USING THIS METHOD THE MUSIC PROGRAM ONLY IS EQUALIZED BY THE MODULE.

BE SURE THAT THE TONE BYPASS SWITCH IS IN THE ON POSITION

1) Connect the Output of the PROGRAM SOURCE unit to the Module IN Jack.

2) Connect the EQ. OUT Jack of the Module to INPUT 4/AUX 1 of the Amplifier.

LEVEL CONTROLS - Adjust INPUT 4/AUX 1 Front Panel Control to 1 o'clock. Turn Rear Panel ATTENUATOR Control slowly cloc kwise until the desired Output Level is achieved After above adjustments are completed use the INPUT 4/AUX 1 Front Panel Control to increase or decrease the Music Level as desired.

CAUTION: PRIOR TO INSTALLING THE BOSE® MODULE IN THE AMPLIFIER FOLLOW THE INSTRUCTIONS SUPPLIED WITH THE MODULE AND THEN READ THE INSTRUCTIONS IN THIS MANUAL’S “INSTALLING A MODULE” SECTION

METHOD 2

USING THE EQ LINK

BY USING THIS METHOD ALL THE AMPLIFIER INPUTS ARE EQUALIZED BY THE MODULE.

BE SURE THAT THE TONE BYPASS SWITCH IS IN THE ON POSITION

1) Connect the Output of the PROGRAM SOURCE unit to the INPUT 4 (or INPUT 2) L and R Jacks.

2) Connect the EQ. OUT Jack of the Module to the POWER IN Jack of the Amplifier.

3) Connect the EQ. IN Jack of the Module to the PREAMP. OUT Jack of the Amplifier.

4) Set EQ LINK Switch on the Amplifier to IN.

Fig. 26B - Method 2 Module Wiring Diagram

INSTALLATION AND WIRING

DIGITAL MUSIC AMPLIFIERS

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC SERIES

METHOD 1

Equalize

Music Only

WARNING: THIS APPLIANCE

MUST BE EARTHED

INPUT 2 (MIC)

BOSE MODULE METHOD 01

SET TONE BYPASS

Connect to INPUT 4/AUX 1

SWITCH TO ON

LISTED

COMMERCIAL

AUDIO

EQUIPMENT

30TJ

EQ LINK

IN OUT

EQ LINK

SUB OUT

PRE EQ

SUB OUT POST EQ

MIX

BUSS

LINE OUT

600

INPUT 4 REMOTE VOLUME

TONE

BYPASS

AUX2 47Kohm 100 mV INPUT5 (MIC-AUX2)

MUSIC OUTPUT

SATELLITE RECEIVER

PRE

OUT

POWER

INPUT 4 (MIC) INPUT 3 (MIC) G COM HOT RVC RVC G COM HOT G COM HOT G COM HOT

250ohm 1.5mV

BALANCED

INPUT-4(AUX1) 47kohm 100mV

(AUX1)

ATTENUATOR

OFF

CD PLAYER

TEL

G COM HOT

600 ohm 100mV

TRACK 01

INPUT-5(AUX2)

47kohm 100mV

ATTENUATOR

BY INTERNAL

TEL OUTPUT

(AUX2)

INPUT 5

MIC-AUX2

SWITCH

LEVEL

Connect to

Module

EQ OUT

AUDIO

OUT

102 EQ. MODULE

Connect Music

Source Output

to Module EQ IN

PAGE 30

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE DMS3040/3080/3120

RESTAURANT/DINER WITH MUSIC AND JUKEBOX - APP. DATA 121

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

JUMPER

APPLICATION

This Note illustrates a typical installation in a Restaurant/Diner/Lounge using Background Music and a Jukebox. The Background Music can be automatically interrupted when the Jukebox is activated. The Background Music is then automatically restored once the Jukebox stops pla ying.This built-in feature of the DMS Amplifier eliminates the need of any external device.

PAGING MICROPHONE

PRIORITY PAGING MICROPHONE - A Low Impedance Dynamic Microphone can be connected to the Amplifier INPUT 1. The Microphone Input can be set to provide

Priority Paging

over both the Music Program and the Jukebox if activated. Optionally Paging may be generated from the Phone system if desired.

PAGING FROM THE PHONE SYSTEM

PRIORITY PAGING FROM THE PHONE SYSTEM - Paging may be generated from a Phone System by using the TEL INPUT of the Amplifier. The TEL INPUT can be set to provide

Priority Paging

over both the Music Program and the Juk ebo x if activ ated.The TEL INPUT provides a 600 ohm Transformer balanced Phone interface.

MUTE 2 DELAY

The Jukebox Configuration utilizes the VO X/MUTE 2 Buss .In order to prevent the premature JUKEBOX/MUSIC SOURCE switching (the Music Source cuts-in while the Jukebox is active) a MUTE 2 DELAY TRIMMER is available on the Rear panel to increase the MUTE 2 DELA Y as necessary. The MUTE 2 DELAY can be adjusted from 3 to 30 Seconds. EXAMPLE:If the Jukebox is playing and the Tune has a long pause or the long pause while the Jukebox is cycling between CD’s it is possible that the Music Source (Background Music) may cut-in causing annoying and unwanted

chatter

while the Jukebox is still active.T o pre v ent this prob lem the MUTE 2 TIME DELAY should be adjusted accordingly.

JUKEBOX REMOTE VOLUME CONTROL

A Jukebox Remote Volume Control may be provided to adjust the Output Level independently from the Background Music Source. The Jukebox Music Le vel should be set in accordance to the ambient noise which may change during peak business hours.The AUX 1 Input (used for the Jukebox) is equipped with a Remote Volume Control Feature. Use the optional PASO Model RVC10W (10K) Volume Control mounted on a single gang plate.

MUSIC ON HOLD

The Zone 1 Amplifier provides a separate 600 ohm Transformer Balanced Music on Hold Output for the Telephone system. If the Zone 1 Input Selector Switch is set to Input 3, the MOH Output receives only the PROGRAM from the the MUSIC SOURCE without Paging or the Jukebox interruptions.

ZONE 1 & 2 ONE WATT - 8 OHM OUTPUT

The ZONE 1 and ZONE 2 Outputs may be used to cover small area with MUSIC ONLY without interruption from the Microphone or Phone Paging or the music from the Jukebox. The Program Source for both 1 Watt Amplifiers may be independently selected through Internal Jumpers (see Diagram).Output Level may be also independently adjusted by the separate Level Controls.

ZONE 1 AND 2 SPEAKERS

The Wiring Diagram shows the connection of up to 4 (8 ohm) Speakers for the Zone 1 & 2 - 1 Watt Amplifier.When 4 Speakers are used each Speaker Output will be a 1/4 Watt.

INPUT JUMPERS - SWITCHES SETTING

The Diagram indicates the various Input Settings for this application. Some settings may be already “Defaulted”when the Amplifier is shipped and do not need re-setting.

MUTE 1 ON

MUTE 2 ON

JUMPER

SW223

MUTE JUMPERS

OFF

VOX 2 OFF

VOX 1 OFF

JUMPER

SW213

VOX JUMPERS

OFF

INPUT 5 (AUX 2) SETTINGS

AUX 2 MIC 5

AUX 2 - MIC 5 SWITCH

MUTE 1 ON

JUMPER

MUTE JUMPERS

OFF

VOX JUMPERS

OFF

SW208 and SW229

SW217

VOX 2 ON

JUMPER

SW212

SATELLITE RECEIVER

JUKEBOX

AUTOMATICALLY

INPUT 4 (AUX 1) SETTINGS

SW228

AUX 1 MIC 4

AUX 1 - MIC 4 SWITCH

1/4W

OHM

1/4W

OHM

ZONE 2

ONLY ZONE

AUX 2 AUX 1 MOD

JUMPER

Up to Four 8 ohm

SW702

Telephone

OPTIONAL MUSIC

ZONE 1 MOH SETTING

KSU

RING

PASO RVC10W

SHIELD

VOX 2 ON

SW215

MUTES THE

MUSIC SOURCE

WHEN SWITCHED

1/4W

OHM

1/4W

OHM

connected

ZONE 2 SOURCE SETTING

Speakers may be

NO JUKEBOX

MUSIC ON HOLD

RECEIVES MUSIC

ONLY - NO PAGING

MUSIC

SOURCE

JUKEBOX

MUTE-2

DELAY

3 to 30 Sec

INPUT

MUTE 2 DELAY CONTROL

TIME OVER MUSIC SOURCE

ADJUSTS JUKEBOX MUTING

ADJUSTS OUTPUT

ZONE 2 LEVEL CONTROL

LEVEL

ZONE 2

AUX 2

JUMPER

AUX 1 MOD

600 ohm MOH System

600

Ohm

Input

MOH

KSU

(AUX2)

ATTENUATOR

47kohm 100mV

INPUT-5(AUX2)

INPUT-4(AUX1)

47kohm 100mV

(AUX1)

ATTENUATOR

MIX

BUSS

PRE EQ

SUB OUT

PRE

OUT

EQ LINK

30TJ

AUDIO

LISTED

EQUIPMENT

COMMERCIAL

CUS

RVC

MASTER

REMOTE

VOLUME MUTE 1

M1 RVC

MUTE 2

GROUND

UNMUTE

MIC1 G M2

SPEAKERS

LEVEL OF ZONE 2

24V DC

250 mA

VOX RELAY

NC C NO

LEVEL

ZONE 2

SW701

0 8

ZONE 2

0 8

ZONE 1

0 600

AFIN DE REDUIRE LE RISQUE

LEVEL

ZONE 1

ATTENTION:

D'INCENDIE REMPLACER SEUL PAR UN

FUSIBLE DE MEME TYPE.

MUSIC ON HOLD OUTPUT

Telephone System

CAUTION: TO REDUCE THE

RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE

FUSE.

MODULE

STANDARD

PORT ACCEPTS

OFF

IN OUT

CAUTION

DMS3120

CAUTION: REMOVE

POWER CORD FROM

AC OUTLET PRIOR TO

LEVEL

SWITCH

INPUT 5

MIC-AUX2

BY INTERNAL

TEL OUTPUT

TEL

G COM HOT

TONE

BYPASS

AUX2

47Kohm 100 mV

INPUT5 (MIC-AUX2)

600

INPUT 4

LINE OUT

VOLUME

REMOTE

SUB OUT

POST EQ

G COM HOT RVC RVC G COM HOT G COM HOT G COM HOT G COM HOT

INPUT 4 (MIC) INPUT 3 (MIC)

POWER

EQ LINK

INPUT 2 (MIC)

DO NOT OPEN

RISK OF ELECTRIC SHOCK

MUST BE EARTHED

INPUT 1 (MIC)

WARNING: THIS APPLIANCE

850 VA

120 W RMS

117V 60 HZ

DELAY

SENS

VOX-2 MUTE-2

DIGITAL MUSIC AMPLIFIER

PROFESSIONAL AUDIO & SOUND

POWER RATING

SUPPLY VOL T A GE

POWER CONSUMPTION

SENS

VOX-1

1 WA TT

ATTENTION: POUR REDUIRLES RISQUES D' INCENDIE

OU DE CHOC ELECTRIQUE, NE PAS EXPOSER A LA PLUIE

OU L' HUMIDITE, NE PAS ENLEVER LE COUVERCLE. AUCUN

REGLAGE A L' INTERIEUR. POUR REPARATION CONSULTER

UNE PERSONNE QUALIFIEE

COM 8 25V 70V

BALANCED

MOH OUT

GROUND

CAUTION: TO REDUCE THE RISK OF FIRE OR

SHOCK DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE. DO NOT REMOVE COVER.

THERE ARE NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

UNSWITCHED

117V 500W MAX

INSTALLING MODULE

600 ohm 100mV

BALANCED

250ohm 1.5mV

SER. NO.

SPEAKER OUTPUT

DMS3120rear

5A 250V

LINE FUSE

117V 60HZ

TEL INPUT SETTINGS

Phone Paging

MUSIC

PHONE HAS

PRIORITY OVER

INPUT 4

REMOTE

VOLUME

PAGING MICROPHONE

AND JUKEBOX

MUSIC SOURCE

PRIORITY OVER

MICROPHONE HAS

DMS AP121

VOX 1 ON

VOX 2 ON

JUMPER

SW214

VOX JUMPERS

OFF

TIP

AND JUKEBOX

OPTIONAL

REMOTE

VOLUME

JUKEBOX

MIC

LO Z

Push to Talk Key

b50side

VOX 1 ON

JUMPER

VOX JUMPERS

OFF

INPUT 1 (MIC 1) SETTINGS

25V/70V Speaker 25V/70V Speaker 25V/70V Speaker

DMS JUKEBOX APP 121

DIGITAL MUSIC SERIES

AUTO SERVICE STATION C - STORE - APP. DATA 123

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

PAGE 31

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEDMS3040/3080/3120

APPLICATION

This Note illustrates a typical Auto Service Station C-Store application. The size of the Service Station and the number of Gas Pump Islands to cover will determine the amount of outdoor Waterproof Speakers required and the Power Output of the Amplifier.

GAS PUMP OUTDOOR SPEAKERS

40 WATT SYSTEM EXAMPLE - The PASO Model C55DMST Waterproof Music Speaker is recommended.Typically each Speak er should be tapped at 5 Watt. In this configuration up to 8 Speaker may be used with the Model DMS3040 40 Watt Amplifier for distribution of Music and Messages at the Gas Pumps.

For larger systems use a higher power Amplifier and the additional quantity of speakers required.

C _ STORE INDOOR SPEAKERS

The Amplifier is equipped with two independent 1 Watt , 8 ohm Amplifiers = ZONE 1 and ZONE 2. C-STORE - Up to 4+4 Ceiling Speakers may be utilized indoors in the Store area, Rest Rooms or other area such as a separate concession. By utilizing the separate (2) 1 Watt Amplifiers as a first and second zone, only the Music program will be distributed inside the Store. This avoids the continuous and annoying repeating of the messages in the indoor areas. The output level may be adjusted by the 1st and 2nd Zone Level Control.

ZONE 1 - ZONE 2 PROGRAM SOURCE SELECTOR The program Source for each Zone Output may be selected by setting the Zone 1 and 2 Jumper Set to either AUX 1 - AUX 2 or Module Source.

MUSIC ON HOLD

The Zone 1 Amplifier provides a separate 600 ohm Transformer Balanced Music on Hold Output for the Telephone system. If the Zone 1 Input Select Jumper Set is set to AUX 1, the MOH Output receives the Music from the Satellite Receiver without Paging or Messages interruptions.

PAGING MICROPHONE

PRIORITY PAGING MICROPHONE - A Low Impedance Dynamic Microphone can be connected to the Amplifier INPUT 1.The Microphone can be set to provide

Priority Paging

over both the Music Program and the Message Repeater. Optionally Paging may be generated from the Phone system if desired.The TEL INPUT provides a 600 ohm Transformer balanced Phone interface.

MESSAGE REPEATER

The Message Repeater provides pre-recorded Messages at the

Gas Pumps Only

. Each time a message is initiated by the Repeater (AUX 1) the Music (AUX 2) is automatically muted for the dur ation of the message.

REPEATER REMOTE VOLUME

A Master Remote Volume Control PASO Model RVC10W may be provided to adjust the Output Level of the Message Repeater in accordance to the outdoors noise.

MUTE 1 ON

MUTE 2 ON

JUMPER

SW223

MUTE JUMPERS

OFF

VOX 2 OFF

VOX 1 OFF

JUMPER

SW213

VOX JUMPERS

OFF

INPUT 5 (AUX 2) SETTINGS

AUX 2 MIC 5

AUX 2 - MIC 5 SWITCH

SW208 and SW229

MUTE 1 ON

JUMPER

SW217

MUTE JUMPERS

OFF

VOX 2 ON

MESSAGES MUTE

MUSIC AT THE PUMPS

JUMPER

SW212

VOX JUMPERS

OFF

INPUT 4 (AUX 1) SETTINGS

SW228

AUX 1 MIC 4

AUX 1 - MIC 4 SWITCH

1/4W

OHM

1/4W

individual requirement.

OHM

The use of both Outputs is optional follow the

ZONE 2

ONLY ZONE

Up to 4-8 ohm Speakers may be connected to each Output.

CEILING SPEAKERS MOUNTED INSIDE C-STORE

OPTIONAL MUSIC

The Amplifier provides two independent 1 Watt-8 Ohm Outputs.

AWG 18

TWISTED PAIR

OHM

1/4W

CEILING SPEAKERS MOUNTED INSIDE C-STORE RECEIVE MUSIC ONLY - NO MESSAGES OR PAGING

1/4W

ZONE 1

ONLY ZONE

OPTIONAL MUSIC

OHM

ZONE 1 MOH SETTING

AUX 2 AUX 1 MOD

1/4W

OHM

1/4W

JUMPER

SW702

MUSIC

SATELLITE RECEIVER

SOURCE

MESSAGE REPEATER

MUTE-2

ZONE 2

1/4W

OHM

1/4W

OHM

connected

ZONE 2 SOURCE SETTING

Speakers may be

Up to Four 8 ohm

LEVEL

ZONE 1

600 ohm MOH System

MUSIC ON HOLD

RECEIVES MUSIC

ONLY - NO PAGING

NO MESSAGE REPEATER

Telephone

MOH

VOX 1 ON

DELAY

3 to 30 Sec

RECEIVER

OVER SATELLITE

ADJUSTS MESSAGE

REPEATER MUTING TIME

MUTE 2 DELAY CONTROL

SPEAKERS

LEVEL OF ZONE 2

ADJUSTS OUTPUT

ZONE 2 LEVEL CONTROL

LEVEL

AUX 2

JUMPER

AUX 1 MOD

SW701

MUSIC ON HOLD OUTPUT

600

Ohm

Input

KSU

Telephone System

PORT ACCEPTS

(AUX2)

ATTENUATOR

47kohm 100mV

INPUT-5(AUX2)

INPUT-4(AUX1)

47kohm 100mV

(AUX1)

ATTENUATOR

OFF

MIX

BUSS

PRE EQ

SUB OUT

PRE

OUT

EQ LINK

30TJ

AUDIO

LISTED

EQUIPMENT

COMMERCIAL

IN OUT

CUS

RVC

MASTER

REMOTE

VOLUME MUTE 1

M1 RVC

MIC1 G M2

NC C NO

LEVEL

0 8

0 600

LEVEL

CAUTION

1 WA TT

BALANCED

MOH OUT

MUTE 2

GROUND

UNMUTE

24V DC

250 mA

VOX RELAY

ZONE 2

ZONE 1

AFIN DE REDUIRE LE RISQUE

ZONE 1

D'INCENDIE REMPLACER SEUL PAR UN

FUSIBLE DE MEME TYPE.

ATTENTION:

CAUTION: TO REDUCE THE

RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE

FUSE.

MODULE

STANDARD

CAUTION: REMOVE

INSTALLING MODULE

POWER CORD FROM

AC OUTLET PRIOR TO

LEVEL

SWITCH

INPUT 5

MIC-AUX2

BY INTERNAL

TEL OUTPUT

TEL

TONE

BYPASS

AUX2

47Kohm 100 mV

INPUT5 (MIC-AUX2)

600

INPUT 4

LINE OUT

VOLUME

REMOTE

SUB OUT

POST EQ

INPUT 4 (MIC) INPUT 3 (MIC)

POWER

EQ LINK

INPUT 2 (MIC)

DO NOT OPEN

RISK OF ELECTRIC SHOCK

MUST BE EARTHED

INPUT 1 (MIC)

WARNING: THIS APPLIANCE

850 VA

120 W RMS

117V 60 HZ

DMS3120

DIGITAL MUSIC AMPLIFIER

PROFESSIONAL AUDIO & SOUND

POWER RATING

SUPPLY VOL T A GE

POWER CONSUMPTION

ATTENTION: POUR REDUIRLES RISQUES D' INCENDIE

OU DE CHOC ELECTRIQUE, NE PAS EXPOSER A LA PLUIE

OU L' HUMIDITE, NE PAS ENLEVER LE COUVERCLE. AUCUN

REGLAGE A L' INTERIEUR. POUR REPARATION CONSULTER

UNE PERSONNE QUALIFIEE

COM 8 25V 70V

CAUTION: TO REDUCE THE RISK OF FIRE OR

SHOCK DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE. DO NOT REMOVE COVER.

THERE ARE NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

UNSWITCHED

117V 500W MAX

G COM HOT

G COM HOT RVC RVC G COM HOT G COM HOT G COM HOT G COM HOT

DELAY

SENS

VOX-2 MUTE-2

SENS

VOX-1

GROUND

600 ohm 100mV

BALANCED

250ohm 1.5mV

SER. NO.

SPEAKER OUTPUT

DMS3120rear

5A 250V

LINE FUSE

117V 60HZ

Phone Paging

INPUT 4

PAGING MICROPHONE

MICROPHONE HAS

VOX JUMPERS

OFF

TEL INPUT SETTINGS

MUSIC

REPEATER

PHONE HAS

AND MESSAGE

PRIORITY OVER

REMOTE

VOLUME

REPEATER

AND MESSAGE

PRIORITY OVER

SATELLITE RECEIVER

VOX 2 ON

JUMPER

SW214

KSU

TIP

RING

OPTIONAL

PASO RVC10W

REMOTE

VOLUME

MESSAGE

REPEATER

MIC

LO Z

Push to Talk Key

b50side

SHIELD

VOX 1 ON

JUMPER

VOX JUMPERS

OFF

INPUT 1 (MIC 1) SETTINGS

25V/70V Speaker 25V/70V Speaker 25V/70V Speaker

GAS PUMP SPEAKERS - MUSIC/MESSAGES AND PAGING

DMS C-STORE APP 123

PASO

C55DMSTW - White

PASO MODEL B500X MICROPHONE

VOX 2 ON

JUMPER

SW215

Waterproof Speaker

DIGITAL MUSIC SERIES

CUSTOMER SERVICE

PAGE BACK

REPLACEMENT PARTS

Please provide complete information when you request replacement parts from either the Factory or a Paso Authorized Distributor. Be certain to include the Part Number and Description as it appears on the parts list, the Model Number of the unit and if possible the Serial Number and the date of purchase of the unit. Replacement parts inventory is maintained specifically to repair Paso products.Part sales for other reasons or applications will be declined.

ORDERING FROM THE FACTORY

Print all information on a purchase order form and mail to: PASO SOUND PRODUCTS, INC. 4750 Goer Drive - Building F CHARLESTON, SC 29406

Be sure to include the following:

- Paso part number

- Part description

- Quantity required

- Model number of the unit

- Serial number of the unit

- Your payment or your authorization for COD shipment for parts not covered by the Warranty or if your company has a current account with the factory

RETAIN ORIGINAL IN WARRANTY PARTS UNTIL YOU RECEIVE REPLACEMENTS. PARTS THAT SHOULD BE RETURNED TO THE FACTORY WILL BE LISTED ON YOUR PACKING SLIP.

For your convenience replacement parts are also available through Paso Authorized Distributors and Dealers nation wide. Obtain a location list directly from the Factory or your regional Paso Representative.

TECHNICAL CONSULTATION

- Need help with your installation ?

- Need help with the operation of the unit ?

- Need help with a repair ? Call or write for assistance. You will find our Technical Dept..

eager to help or assist you with any technical problem you may have encountered except “`Customizing'' for a unique application.

The effectiveness of our consultation service depends on the accuracy of the information you furnish. Be sure to tell us:

- The Model and Serial number of the unit

- The date of purchase

- An exact description of the difficulty

- All you have done in attempting to correct the problem Call our toll-free phone number:

1-800 231 3034

REPAIR SERVICE

Repair service for out of warranty Paso products may be obtained form your local Paso distributor or any other qualified repair station.

In warranty repairs must be returned to the Factory. Prior authorization must be obtained from the Factory. Products received without authorization will be refused by our Receiving Dept..

IN WARRANTY REPAIR SERVICE

Call or write the Factory to obtain an authorization to return the product for repairs.

Pack the equipment in the original carton or in a strong carton with at least THREE INCHES of resilient packing material on all sides, top and bottom. Seal the carton with reinforced tape and mark it FRAGILE on at least two sides. Remember, the Carrier will not accept liability for shipping damages if the unit is improperly packed.

EQUIPMENT RECEIVED IN DAMAGED CONDITION DUE TO POOR PACKING WILL BE REFUSED AND THE WARRANTY COVERAGE IS AUTOMATICALLY VOIDED.

The Paso Sound Limited Warranty provides: The examination of the returned product must disclose in our

judgement, a manufacturing defect. The warranty does not extend to any product that has been subject to misuse, neglect, accident, improper installation or where the serial number of the product has been removed or defaced.

Ship via insured prepaid United Parcel Service or Parcel Post to:

PASO SOUND PRODUCTS, INC. 4750 Goer Drive - Building F CHARLESTON, SC 29406 Attn. SERVICE DEPARTMENT

The equipment will be returned freight prepaid after repairs. Be sure to include the following:

- Your name and address

- Date of purchase and copy of invoice

- A brief description of the difficulty

- A return address shipping label

OUT OF WARRANTY REPAIR SERVICE

Follow return instructions as per in warranty repair service.Prior to performing all necessary repairs, you will be advised of the charges and at that time a written authorization by you will be required including authorization to return the equipment COD for the service and shipping charges. This will avoid unnecessary delays in returning the equipment to you.

Printed in USA Manual OM 163

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

Paso Sound Products DMS 3040-40, DMS 3080-80, DMS 3120-120, OM163, DMS 3040 Installation Manual And Operating Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual