PASCO PS-2104 User Manual

Instruction Sheet
012-07297E
Force Sensor
PS-2104
Introduction
2
1
3
4
The Force Sensor connects to a PASPORT interface or datalogger and records force in the range of −50 N to + 50 N at a rate of up to 1000 samples per second.
Set-up
Connecting the Sensor to an Interface
1. Connect the sensor’s plug to any port of a PASPORT inter-
face or datalogger.
5
Included Parts
1. Force Sensor
2. Bumper attachment
4. Cart/Bracket thumbscrew (M5 × 45 mm)
5. Rod clamp thumbscrew (1/4-20 × 0.75 inch)
Additional Part Required
PASPORT interface or datalogger
Quick Start
1. Connect the Force Sensor to your PASPORT interface.
2. If you are using a computer, connect the PASPORT interface
to it and start DataStudio.
3. Screw the hook attachment into the sensor.
4. Press or click the start button to begin recording data.
5. Push or pull the hook. The sensor measures the applied
force.
2. If you are using a computer, connect the PASPORT interface
to it and start DataStudio.
Zeroing the Sensor
Press the ZERO button on the sensor. The sensor’s output is adjusted to read zero.
Connecting Bumper and Hook Attachments
Screw the bumper or hook into the sensor as illustrated.
About the Force Measurement
Sample Rate
By default, the sensor collects 10 samples per second. It can col­lect data as fast as 1000 samples per second and as slow as one sample every four hours. Change the sample rate in DataStudio or on your datalogger.
®
Force Sensor PS-2104
Inverted Output
By default, the sensor registers pushing as a positive force and pulling as a negative force. To register pulling as positive and pushing as negative, select the Force (Inverted) measurement in DataStudio or on your datalogger.
Sensor Mounting
Mounting the Sensor on a Rod
Slide the sensor onto a rod and secure it with the thumbscrew as illustrated.
Specifications
Range ±50 N
Resolution 0.03 N
Maximum Sample Rate 1000 samples/s
Technical Support
For assistance with any PASCO product, contact PASCO at:
Address: PASCO scientific
10101 Foothills Blvd. Roseville, CA 95747-7100
Phone: 916-786-3800 (worldwide)
800-772-8700 (U.S.)
Fax: 916-786-7565
Web: www.pasco.com
Email: support@pasco.com
For more information about the Force Sensor and the most up-to-date version of this Instruction Sheet, visit:
Mounting the Sensor on a PASCO Cart
1. Insert the included Cart/Bracket thumbscrew through the hole in the senor labeled Cart.
2. Screw the thumbscrew into the threaded hole on the top of the cart.
Mounting the Sensor on an IDS Bracket
1. Insert the included Cart/Bracket thumbscrew through the hole in the IDS Force Accessory Bracket (PASCO part CI-6545).
2. Screw the thumbscrew into the hole in the sensor labeled IDS Bracket.
www.pasco.com/go?PS-2104
Limited Warranty For a description of the product warranty, see the PASCO catalog. Copyright The PASCO scientific 012-07297E
Sheet
is copyrighted with all rights reserved. Permission is granted to non-profit educational institutions for reproduction of any part of this man­ual, providing the reproductions are used only in their laboratories and classrooms, and are not sold for profit. Reproduction under any other cir­cumstances, without the written consent of PASCO scientific, is prohibited. Trademarks PASCO, PASCO scientific, and PASPORT are trademarks or registered trademarks of PASCO scientific, in the United States and/or in other countries. All other brands, products, or service names are or may be trademarks or ser vice marks of, and are used to identify, products or services of, their respective owners. For more information visit www.pasco.com/legal.
Force Sensor Instruction
2
®
Loading...