OPERATOR MANUAL
ISSUE 1
XTI-160 M
Welcome
Thank you and congratulations on choosing Parweld. This Owner’s Manual is designed to help you get
the most out of your Parweld products. Please take time to read the Safety precautions. They will
help you protect yourself against potential hazards in the workplace. With proper maintenance this
equipment should provide years of reliable service. All our systems conform to ISO9001: 2000 and
are independently audited by NQA.
The entire product range carries the CE mark, and is constructed in accordance with European
directives and the product specic standards where they apply.
Further Information
Parweld is the UK’s leading manufacturer of MIG, TIG and Plasma torches and consumables.
For more information about Parweld’s complete range visit: www.parweld.com
CONTENTS
Contents
Page
1.0 Safety Precautions 4
2.0 Product description 5
3.0 Technical Specications 5
4.0 Description of controls 6
5.0 Installation 7
5.1 Unpacking the Machine 7
5.2 Location 7
5.3 Input and grounding connection 7
5.4 MIG welding torch setup 7
6.0 Operation 8
6.1 MIG Welding guide 8
7.0 Fault nding 10
8.0 Accessories 13
8.1 Torch spares 14
9.0 EC declaration of conformity 18
9.1 RoHS Compliance Declaration 18
9.2 WEEE Statement 19
9.3 Statement of warranty 19
www.parweld.com
4
1.0 Safety Precautions
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks or severe burns.
The electrode and work circuit is electrically live whenever the output
is on. The input power circuit and machine internal circuits are also
live when power is on.
Do not touch live electrical parts.
Wear dry, sound insulating gloves and body protection.
Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
ground.
Additional safety precautions are required when any of the following
electrically hazardous conditions are present: in damp locations
or while wearing wet clothing; on metal structures such as oors,
gratings, or scaffolds; when in cramped positions such as sitting,
kneeling, or lying; or when there is a high risk of unavoidable or
accidental contact with the work piece or ground.
Disconnect input power before installing or servicing this equipment.
Lockout/tagout input power according to Safety Standards.
Properly install and ground this equipment according to national and
local standards.
Always verify the supply ground - check and ensure that input power
cable ground wire is properly connected to ground terminal in the
receptacle outlet.
When making input connections, attach proper grounding conductor
rst - double-check connections.
Frequently inspect input power cable for damage or bare wiring replace cable immediately if damaged - bare wiring can kill.
Turn off all equipment when not in use.
Do not use worn, damaged, under sized, or poorly spliced cables.
Do not drape cables over your body.
If earth grounding of the work piece is required, ground it directly
with a separate cable.
Do not touch electrode if you are in contact with the work, ground, or
another electrode from a different machine.
Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
Wear a safety harness if working above oor level.
Keep all panels and covers securely in place.
Clamp work cable with good metal-to-metal contact to work piece or
worktable as near the weld as practical.
Insulate work clamp when not connected to work piece to prevent
contact with any metal object.
Welding produces fumes and gases. Breathing these fumes and
gases can be hazardous to your health.
FUMES AND GASES can be hazardous.
Keep your head out of the fumes. Do not breathe the fumes.
If inside, ventilate the area and/or use local forced ventilation at the
arc to remove welding fumes and gases.
If ventilation is poor, wear an approved respirator.
Read and understand the Material Safety Data Sheets (MSDS’s) and
the manufacturer’s instructions for metals, consumable, coatings,
cleaners, and de-greasers.
Work in a conned space only if it is well ventilated, or while wearing
an air-supplied respirator. Always have a trained watch person
nearby. Welding fumes and gases can displace air and lower the
oxygen level causing injury or death. Be sure the breathing air is
safe.
Do not weld in locations near de-greasing, cleaning, or spraying
operations. The heat and rays of the arc can react with vapours to
form highly toxic and irritating gases.
Do not weld on coated metals, such as galvanized, lead, or cadmium
plated steel, unless the coating is removed from the weld area, the
area is well ventilated, and while wearing an air-supplied respirator.
The coatings and any metals containing these elements can give off
toxic fumes if welded.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense, visible and
invisible (ultraviolet and infrared) rays that can burn eyes and skin.
Sparks y off from the weld.
Wear an approved welding helmet tted with a proper shade of lter
lense to protect your face and eyes when welding or watching
Wear approved safety glasses with side shields under your helmet.
Use protective screens or barriers to protect others from ash, glare
and sparks; warn others not to watch the arc.
Wear protective clothing made from durable, ame resistant material
(leather, heavy cotton, or wool) and foot protection. Welding on
closed containers, such as tanks, drums, or pipes, can cause them
to blow up. Sparks can y off from the welding arc. The ying sparks,
hot work piece, and hot equipment can cause res and burns.
Accidental contact of electrode to metal objects can cause sparks,
explosion, overheating, or re. Check and be sure the area is safe
before doing any welding.
WELDING can cause re or explosion.
Remove all ammables within 10m of the welding arc. If this is not
possible, tightly cover them with approved covers.
Do not weld where ying sparks can strike ammable material.
Protect yourself and others from ying sparks and hot metal.
Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
SAFETY
5
Watch for re, and keep a re extinguisher nearby. Be aware that
welding on a ceiling, oor, bulkhead, or partition can cause re on
the hidden side.
Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to local regulations
Connect work cable to the work as close to the welding area as
practical to prevent welding current from travelling along, possibly
unknown paths and causing electric shock, sparks, and re hazards.
Wear oil-free protective garments such as leather gloves, heavy
shirt, cufess trousers, high shoes, and a cap. Remove any
combustibles, such as a butane lighter or matches, from your person
before doing any welding.
FLYING METAL can injure eyes.
Welding, chipping, wire brushing, and grinding cause sparks and
ying metal. As welds cool they can throw off slag. Wear approved
safety glasses with side shields even under your welding helmet.
BUILDUP OF GAS can injure or kill.
Shut off shielding gas supply when not in use. Always ventilate
conned spaces or use approved air-supplied respirator.
HOT PARTS can cause severe burns.
Do not touch hot parts with bare hands.
Allow cooling period before working on gun or torch.
To handle hot parts, use proper tools and/or wear heavy, insulated
welding gloves and clothing to prevent burns.
MAGNETIC FIELDS can affect pacemakers.
Pacemaker wearers keep away.
Wearers should consult their doctor before going near arc welding,
gouging, or spot welding operations.
NOISE can damage hearing.
Noise from some processes or equipment can damage hearing.
Wear approved ear protection if noise level is high.
Shielding gas cylinders contain gas under high pressure.
CYLINDERS can explode if damaged.
Protect compressed gas cylinders from excessive heat, mechanical
shocks, physical damage, slag, open ames, sparks, and arcs.
Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping. Keep cylinders
away from any welding or other electrical circuits. Never drape a
welding torch over a gas cylinder. Never allow a welding electrode to
touch any cylinder. Never weld on a pressurized cylinder - explosion
will result. Use only correct shielding gas cylinders, regulators,
hoses, and ttings designed for the specic application; maintain
them and associated parts in good condition.
Turn face away from valve outlet when opening cylinder valve.
Use the right equipment, correct procedures, and sufcient number
of persons to lift and move cylinders.
Read and follow instructions on compressed gas cylinders,
associated equipment, and Compressed Gas Association (CGA)
recommendations.
2.0 Product Description
This welding machine is manufactured using
advanced inverter technology. The input voltage is rectied to
DC and then inverted to high frequency AC voltage. before being
converted back to DC for the output .This allows the use of a much
smaller transformer and so allowing weight saving and improved
power efciency.
3.0 Technical
Specications
XTI-160M
Input voltage
230V +/- 10%
Frequency
50/60Hz
Input current
25A max
16 eff
Fuse rating
16A
Output OCV
42
MIG 50-160A
X 40% 100%
I2 160A 115A
SAFETY
www.parweld.com
6
5.0 Installation
Read entire installation section before starting installation.
SAFETY PRECAUTIONS
• ELECTRIC SHOCK can kill.
• Only qualied personnel should perform this installation.
• Only personnel that have read and understood the Operating
Manual should install and operate this equipment.
• Machine must be grounded per any national, local or other
applicable electrical regulations.
• The power switch is to be in the OFF position when installing
work cable and electrode cable and when connecting other
equipment.
4.0 Description of Controls
1) Amperage Display. Displays the welding amperage or wire speed
during welding
2) Voltage Display. Displays the welding voltage during welding
3) Voltage control This function controls the MIG welding voltage. It
can be adjusted innitely withing the working voltage range.
4) Negative output connection used to connect the work return cable.
This is the 50mm Dinse connection socket.
5) MIG torch euro connector, for connection of the MIG torch
6) Latching trigger selector. 2 Arrows denotes momentary trigger, 4
arrows denotes latching trigger.
7) Inductance control, this hardens or softens the arc in MIG welding,
8) Amperage control for adjusting the Amperage (wire feed speed)
Power light This indicates mains power is applied to the machine
and that the machine is currently switched on when the light is
illuminated.
14) MIG wire spool holder accepts 5KG (200mm ) spools
15) Wire feed box
16) Wire tension adjuster
ON OFF Switch for switching on or off the mains supply to the
machine. (mounted on the rear of the machine)
Note the output of the machine is permanently on in MMA
mode unless the on/off switch is in the off position.
1
2
3
4
5
CONTROLS
6
7
8
14
15
16
7
5.1 Unpacking the Machine
Carefully remove the machine from the packaging, we recommend
you retain the packaging until the machine has been fully installed
and tested incase it has been damaged in transit and has to be
returned to the re-seller.
5.2 Location
Be sure to locate the welder according to the following guidelines:
In areas, free from moisture and dust.
Ambient temperature between 0-40
0
C.
In areas, free from oil, steam and corrosive gases.
In areas, not subjected to abnormal vibration or shock.
In areas not exposed to direct sunlight or rain.
Place at a distance of 12” (300 mm) or more from walls or similar
that could restrict natural airow for cooling.
5.3 Input and grounding connection
WARNING
Before starting the installation, check that your power supply
is adequate for the voltage, amperage, phase, and frequency
specied on the Machine nameplate.
Operate the welding power source from a single-phase 50/60 Hz,
AC power supply. The input voltage must match one of the electrical
input voltages shown on the input data label on the unit nameplate.
The XIT 160M machine should only be used on 230V supply. Refer
to the specications table for voltage tolerances.
Have a qualied electrician connect the input plug. For long runs
over 30m , larger copper wires should be used. The green/yellow
wire in the input cable connects to the frame of the machine. This
ensures proper grounding of the machine when the machine plug is
inserted into the receptacle.
5.4 MIG welding torch setup
The welder, as shipped from the factory, is connected for electrode
positive (+) polarity. This is the normal polarity for MIG welding. The
polarity of the welding set cannot be changed.
5.4.1 Changing drive roll sets
1. Turn off the power source.
2. Release the pressure on the idle roll by pulling the pressure
adjuster towards the wire spool holder. The idle roll assembly
should now hinge down away from the pressure roll.
3. Unscrew the plastic knob retaining the grooved drive roll and
side off the drive roller.
4. Ensure the wire size marked on the side of the feed roller
matches the wire size to be used.
5. Replace the drive in reverse of the above procedure ensuring
the wire size to be used is marked on the outward facing side of
the roller as it is retted.
NOTE: Be sure that the torch liner and contact tip are also sized
to match the selected wire size.
5.4.2 Welding wire installation
Open the Wire Drive Compartment Door
6. Unscrew the plastic retaining wheel from the end of the spool
holder shaft.
7. Position the wire spool so that it will rotate in a direction when
feeding so as to be de-reeled from the bottom of the coil.
8. Slide the wire spool all the way onto the shaft and ret the
plastic retaining nut.
Note:- there is a friction brake on the reel hub assembly to
prevent the wire spool over running when welding stops ensure
the this is slackened to the minimum setting. It can be adjusted
by means of the nut visible when the plastic nut is removed.
9. Turn the Spool until the free end of the electrode is accessible.
While securely holding the electrode, cut off the bent end and
straighten the rst 100mm. (If the electrode is not properly
straightened, it may not feed properly through the wire drive
system Manually feed the wire from the wire reel and through
the wire guide and then over the top of the wire feed roller
(ensure the pressure arm is in its raised position.)
10. Continue to feed the wire through the outlet guide until 20mm of
wire is protruding from the front of the machine torch connector.
11. Reposition the adjustable pressure arm to its original position to
apply pressure. Adjust pressure as necessary.
Note the pressure arm should be adjusted in order to give
the minimum amount of pressure on the wire to allow reliable
feeding,
5.4.3 Torch installation
Your Parweld MIG/MAG Welding Torch has been supplied ready to
weld. It has been supplied with the standard consumables denoted
in the product brochure.
To connect the torch to the power source:-
1. Remove the tip adaptor and contact tip
2. Inch the wire from the exit of the wire guide on the feed unit
as Figure 1. Ensure that it does not short out on any machine
panels.
3. Carefully slide the electrode wire into the torch liner and
slowly locate the torch gun plug body into the feed unit central
connector and tighten the gun plug nut as Figure 2
Note; To aid the initial location of a new torch and to prevent
OPERATION
www.parweld.com
8
or aluminium wire, may require less pressure than the factory
setting. The optimum idle roll setting can be determined as
follows:
2. Press end of gun against a solid object that is electrically
isolated from the welder output and press the gun trigger for
several seconds.
3. If the wire “bird nests”, jams or breaks at the drive roll, the idle
roll pressure is too great. Back the adjustment knob out 1/2
turn, run new wire. If the only result was drive roll slippage,
loosen the Hand nut on the central connector and pull the gun
forward about 6” (15cm) away from the power source. There
should be a slight waviness in the exposed wire. If there is no
waviness, the pressure is too low. Tighten the adjustment knob
1/4 turn, reinstall the gun cable and repeat the above steps.
6.1.1 Feeding wire electrode
1. When triggering, the electrode and drive mechanism are
electrically “LIVE” relative to work and ground and remain
“LIVE” several seconds after the gun trigger is released.
WARNING
When using an open arc process, it is necessary to use correct
eye, head, and body protection.
2. Position wire over joint. The end of the wire may be lightly
touching the work.
3. Lower welding helmet, operate gun trigger, and begin welding.
Hold the gun so the contact tip to work distance is about 3/8”
(10 mm).
4. To stop welding, release the gun trigger and then pull the gun
away from the work after the arc goes out.
5. When no more welding is to be done, close valve on gas
cylinder (if used), momentarily operate gun trigger to release
gas pressure and turn off the machine.
6.1.1 Optimising weld parameters
NOTE These settings are guidelines only. Material and wire
type, joint design, t up, position, shielding gas, etc. affect
settings. Produce test welds to be sure they comply to
specications.
Material thickness determines weld parameters.
1. Convert Material Thickness to Amperage (A) (0.25mm= 1 Amp)
3.2mm = 125 A
2. Select Wire Size
Amperage Range Wire Size
40 - 145 A 0.8 mm
50 - 180 A 1.0 mm
3. Select Wire Speed (Amperage)
Wire Size Feed speed
0.8 mm 0.05m/min per Amp
1.0 mm 0.04m/min per Amp
So based on 3.2 mm material thickness amperage should be 125A if
using 1.0mm wire then the wire feed speed should be
damage to the gas nipple O-ring a very light application of
grease to the O Ring is benecial.
4. Keeping the torch as straight as possible, use the torch trigger
to feed the electrode wire 50mm from the end of the liner
conduit.
5. Once the electrode wire has stopped, ret the tip adaptor,
diffuser, contact tip and gas nozzle.
6. Trim the electrode wire to within 5mm of the face of the nozzle,
this will facilitate jolt free arc initiation.
7. Press the gas purge button and check the gas ow is adequate
for your application.
8. An inexpensive ow meter is available from Parweld reference
806001.
5.4.4 Work return lead connection
Insert the work return lead connector into the Negative dinse
receptacle on the front panel of the machine and twist it clockwise
until tightly secured.
Connect the earth clamp to the work piece as close as possible to
the point to be welded and ensure that a good electrical connection
is created to bare metal.
5.4.4 Shielding gas connection
1. Using the gas hose supplied connect the hose to the gas inlet
connection on the rear of the machine and tighten it with a
spanner.
2. Connect the opposite end of the gas hose to the output
connection of a gas regulator capable of supplying the correct
gas ow for the welding operation.
Note The gas cylinder should be secured to ensure it cannot
fall.
6.0 Operation
WARNING
When using an open arc process, it is necessary to use correct
eye, head, and body protection.
6.1 MIG Welding
Controls used
2T/4T sets the trigger to momentary or latching for longer
welding runs.
Voltage adjustment knob, allows the adjustment of welding
voltage
Current adjustment knob which controls the wire feed speed
Inductance control which controls the smoothness of the arc
Note: Check that drive rolls, and torch parts are correct for the
wire size and type being used.
1. The optimum idle roll pressure varies with type of wire, wire
diameter, surface conditions, lubrication, and hardness. As a
general rule, hard wires may require greater pressure, and soft,
FAULT
FINDING
9
0.04 X 125= 5m/min
Wire speed (amperage) controls weld penetration
4. Select Voltage. Voltage controls height and width of weld
bead.
Low Voltage: wire stubs into work
High Voltage: arc is unstable (spatter)
Set voltage midway between high/low voltages.
And then ne tune accordingly
7.0 Fault Finding
Weld quality is dependent on the selection of the correct
consumables, maintenance of equipment and proper welding
technique.
Power source problems
Description Possible cause Remedy
The welding
arc cannot be
established
(a) The primary supply
voltage has not been
switched on
(b) The welding power
source switch is switched
off
(c) Loose connections
internally
(a) Switch on the
primary supply
voltage
(b) Switch on the
welding power
source.
(c) Have a
qualied service
engineer repair the
connection
Maximum
output welding
current cannot
be achieved
with nominal
mains supply
voltage
Defective control circuit Have a qualied
service engineer
inspect then repair
the welder
Welding
current
reduces when
welding
Poor work lead
connection to the work
piece
Ensure that the
work lead has a
reliable electrical
connection to the
work piece
A total loss of
power, pilot
lamp is off,
no output,
the fan is not
operating
(a) Failure of input
voltage
(b) Possible over voltage
(c) Internal fault with the
machine
(a) Re-establish
mains supply
(b) Check voltage
and if necessary
move machine to
alternative supply
(c) Have a qualied
service engineer
inspect then repair
the welder
Description Possible cause Remedy
Fault lamp is
on, no power
output
(a) Machine overheated
(b) Over current state
(c) Internal fault with
machine
(a) Allow to cool
with fan running
(b) Switch off
mains power to the
machine and re start
(c) Have a qualied
service engineer
inspect
then repair the
welder
ROUTINE MAINTENANCE
The only routine maintenance required for the power supply is a
thorough cleaning and inspection, with the frequency depending on
the usage and the operating environment.
Warning
Disconnect primary power at the source before removing the cover.
Wait at least two minutes before opening the cover to allow the
primary capacitors to discharge.
To clean the unit, remove the screws securing the outer cover,
lift off the outer cover and use a vacuum cleaner to remove any
accumulated dirt and dust. The unit should also be wiped clean,
if necessary; with solvents that are recommended for cleaning
electrical apparatus.
FAULT
FINDING
www.parweld.com
8.0 Accessories
8.1 Torch spares
Stock Code Description
CKE403 Electrode Holder with 3m Lead
CKC403 Earth Lead 3m with Clamp
ER17-12S1BGD Direct fit Tig Torch
WP17AK Tig Spares Kit in Plastic Case
8.2 Gas equipment
Everyday Gas Regulators –
300 BAR
Single Stage
Features
Flow rate up to 96m3/h (3389 ft3/h)
• Full 300 bar capability
• Outlet pressure indicated on the bonnet
• Bottom entry design suited for top outlet cylinder valves
Fittings
• Fitted with standard
3
/8” BSP outlet
• Fitted with 5/8” BSP inlet connections
Stock Code Description Maximum Outlet Pressure
E700140 Argon Preset Regulator 3.0 Bar
E700141 Argon Indicator Regulator 3.0 Bar
E700113 1 Gauge Argon 30 lpm flow
E700123 2 Gauge Argon 30 lpm flow
Flow Meters
Features
• Designed from brass bar whilst the tube and cover are
moulded from high quality polycarbonate to ensure high
impact resistance and clarity
• Calibrated to operate at an inlet pressure
of 30PSI
• Sensitive needle valve provides easy
adjustment and the downward facing outlet
ACCESSORY
www.parweld.com
Model
Stock Code 3M 4M Model Description
ECR1500 -30ER -40ER Everyday Welding Torch
c/w Euro Fitting
Nozzles
Stock Code Description
A ECO1530* Everyday Conical Nozzle 15/329/12mm Bore
B1529 Everyday Cylindrical Nozzle 5/89/16mm Bore
B1531 Everyday Tapered Nozzle 7/169/11mm Bore
B1532 Everyday Bottle Nozzle 1/29/13mm Bore
B1533 Everyday Spot Welding Nozzle 5/89/16mm Bore
Contact Tips
Stock Code Description
B ECO1527-06 Everyday Contact Tip 0.0239/0.6mm M6 Eco
ECO1527-08* Everyday Contact Tip 0.0309/0.8mm M6 Eco
Liners
Stock Code Description
C ECO1535-30 Everyday Steel Liner .0239-.0309/0.6-0.9mm x 3m
ECO1535-40 Everyday Steel Liner .0239-.0309/0.6-0.9mm x 4m
Components
Stock Code Description
* Denotes Standard Build
1 B1504 Shroud Spring
2 B1507 L/H Tip Adaptor
3 ECO1501 Swan Neck c/w Tip Adaptor & Insulation Sleeve
4 ECO1502 One Piece Neck Insulation Sleeve
5 B2519 Hexagonal Fitting
6 B1515/ER Ergo Handle Location Body
7 B1505 Lock Nut
8 ECO8016 Spring Cable Support c/w Knuckle Joint
9 B1521 Cable Terminal – Female
10 B1541 Handle Screw
11 ECO2514 Everyday Ergo Handle Kit
12 ECO2516 Everyday Ergo Trigger
13 B1517-30 Cable Assembly x 3.0m
B1517-40 Cable Assembly x 4.0m
B1517-50 Cable Assembly x 5.0m
14 B1522 Cable Terminal – Male
15 B1841 Cable Support
16 B1518/BK Gun Plug Housing c/w Nut
17 B1526 Gun Plug Screw
18 B1519PL/BK Gun Plug Nut, Plastic c/w Insert
19 Fixed Pin Fixed Pin Assembly
20 ECB1528 Gun Plug Body c/w Fixed Pins
21 B1524 Gun Plug ‘O’ Ring
22 B1525 Liner Nut
Everyday 150A
Air Cooled MIG Welding Torch
Rating: 180A CO
2 150A mixed gas, @ 60% duty cycle. EN60974-7 .0239-.0409/0.6-1.0mm wires
A
B
1
2
3
4
14
5
6
9
11
12
15
16
17
18
19
20
21
22
C
7
7
10
8
13
12
12
www.parweld.com
9.0 EC declaration of conformity
Hereby we declare that the machines as stated below
Type: XIT 160M
Conform to the EC Directives: 73/23/EEC and 89/336/EEC
European standard: EN/IEC 60974-1
This is to certify that the tested sample is in conformity with all provisions of the above detailed EU directives and product standards.
9.1 Rohs Compliance Declaration
Directive 2002/95/ec of the European Parliament
Restriction of use of certain hazardous substances in electrical and electronic equipment
Type: XIT 160M
The above listed products are certied to be compliant with the rohs directive with all homogeneous component parts being controlled to
ensure material contents as per the list below.
Cadmium 0.01% by weight
Lead 0.1% by weight
Mercury 0.1% by weight
Hexavalent chromium 0.1% by weight
Polybrominated biphenyl’s (pbbs) 0.1% by weight
Polybrominated diphenyl ethers (pbdes) 0.1% by weight
It should be noted that under specic exempted applications, where lead is used as an alloying element the following limits are applied in
accordance with the regulations.
Copper and copper alloy parts use less than 4% by weight of each homogeneous component.
Steel and steel alloy parts use less than 4% by weight of each homogeneous component.
Aluminium and aluminium alloy parts use less than 4% by weight of each homogeneous component.
Only dispose off in authorised sites for electrical and electronic waste do not dispose of with general refuse or landll waste.
www.parweld.com
13
9.2 WEEE Statement
WEEE (Waste Electrical & Electronic Equipment) 2002/96/EC
In relation to implementing the legislation, Parweld has established relevant recycling and recovery methods. We have been fully compliant
against the marking requirements since August 2005. Parweld is registered in the UK with the Environment agency as detailed below. For
WEE compliance outside the UK please contact your supplier/Importer
Parweld is registered with a compliance scheme Ofcial registration number is WEE/FD0255QV
When your equipment reaches the end of its service life you should return it to Parweld where it will be reconditioned or processed for
recycling.
9.3 Statement of warranty
Limited Warranty:
Parweld Ltd, hereafter, “Parweld” warrants its customers that its products will be free of defects in workmanship or material. Should any failure
to conform to this warranty appear within the time period applicable to the Parweld products as stated below, Parweld shall, upon notication
thereof and substantiation that the product has been stored, installed, operated, and maintained in accordance with Parweld’s specications,
instructions, recommendations and recognized standard industry practice, and not subject to misuse, repair, neglect, alteration, or accident,
correct such defects by suitable repair or replacement, at Parweld’s sole option, of any components or parts of the product determined by
Parweld to be defective.
Parweld makes no other warranty, express or implied. This warranty is exclusive and in lieu of all others, including, but not limited to any
warranty of merchantability or tness for any particular purpose.
Limitation of Liability:
Parweld shall not under any circumstances be liable for special, indirect or consequential damages, such as, but not limited to, lost prots and
business interruption. The remedies of the purchaser set forth herein are exclusive and the liability of Parweld with respect to any contract, or
anything done in connection therewith such as the performance or breach thereof, or from the manufacture, sale, delivery, resale, or use of any
goods covered by or furnished by Parweld whether arising out of contract, negligence, strict tort, or under any warranty, or otherwise, shall not,
except as expressly provided herein, exceed the price of the goods upon which such liability is based. No employee, agent, or representative
of Parweld is authorized to change this warranty in any way or grant any other warranty.
Purchaser’s rights under this warranty are void if replacement parts or accessories are used which in Parweld’s sole judgement may impair the
safety or performance of any Parweld product.
Purchaser’s rights under this warranty are void if the product is sold to purchaser by non-authorized persons.
The warranty is effective for the time stated below beginning on the date that the authorized Distributor delivers the products to the purchaser.
Notwithstanding the foregoing, in no event shall the warranty period extend more than the time stated plus one year from the date Parweld
delivered the product to the authorized distributor.
Parweld Limited
Bewdley Business Park
Long Bank
Bewdley
Worcestershire
England
DY12 2TZ
tel. +44 1299 266800
fax. +44 1299 266900
www.parweld.com
info@parweld.co.uk
Loading...