How it Works
Partner Tech
Loading...
EM100
Users Manual
46 pgs3.86 Mb0

Partner Tech EM100 Users Manual

EM-100
User Manual
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of PARTNER Tech Corp.
Trademark recognition
All product names used in this manual are the properties of their respective owners and are acknowledged.
Federal Communications Commission (FCC)
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modications not ex­pressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.
Declaration of conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer­ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
Federal Communication Commission Interference Statement
You are cautioned that changes or modifications not expressly approved by thepart responsible for compliance could
void the user’s authority to operate the equipment.
FCC Radio Frequency (RF) Exposure Caution Statement “The manufacture declares that this device is limited to Channels 1 through 11 in the 2.4GHz frequency by specified firmware controlled in the USA.”
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. Max. SAR Measurement (1g) 802.11b/g 11b: 0.193 W/kg ; 11g: 0.159 W/kg
i
ii
About this manual
This manual is intended for system administrators who are familiar with setting up a new system and install­ing programs.
The manual consists of the following sections:
Chapter 1 Getting Started: This section covers unpacking and checking the
Chapter 2 Learning The Basics: The chapter provides information how to use the basic
Chapter 3 Using The Accessories: This section provides information how to use the
Appendix: The appendix covers troubleshooting, information
package contents, identifying components, charge the battery, install the SD card and power it on..
features.
accessories.
on having the EM-100 serviced, and technical
specications.
Safety information
Before installing and using the EM-100, take note of the following precautions:
Request service for damaged products:
» Turn off the product, unplug it from the electrical outlet, and
request service from a service partner under the following conditions:
•
The power cord or plug is damaged.
Liquid has been spilled into the product.•
An object has fallen into the product.•
The product has been exposed to rain or water.•
The product has been dropped or damaged.•
The product does not operate normally when you follow the operating instructions.•
Avoid hot areas: » The product should be placed away from heat sources such as radiators, heat registers,
stoves, and other products (such as ampliers) that produce heat.
» Allow the product to cool before removing covers and touching internal
Allow the product to cool:
components.
» Never use the product in a wet location (more than 90% humidity).
Avoid wet areas:
» Never insert objects of any kind into slots or other openings in the
Avoid inserting objects into product:
product.
» Unplug the product from the wall outlet before cleaning it. Do not use liquid
Clean the product properly:
cleaners or aerosol cleaners. Use a soft cloth dampened with water for cleaning exterior components, but NEVER apply water directly to the product or to an LCD screen.
» Do not use the product on an unstable table, cart, stand, tripod,
Use recommended mounting accessories:
or bracket. Mount the product according to the manufacturer’s instructions, and use a mounting accessory recommended by the manufacturer.
» Use your product only with the computers and accessories
Use the product with approved equipment:
identied as suitable for use with your product.
» Turn down the volume before using headphones or other audio devices.
Adjust the volume:
»
Use only an approved adapter.
iii
This device has a built-in Li-polymer battery. To reduce the risk of re or burns, do not disassemble, » crush, puncture a battery pack. If expose the battery in re, the battery will crack, explode or release
dangerous chemicals.
»
There is a danger of explosion if a battery pack is incorrectly replaced. Replace it only with an
approved battery pack for this product.
»
Replace the battery with the same type as the product’s battery we recommend in the product
specication list. Use of another battery may present a risk of re or explosion
»
When a battery pack has reached the end of its useful life, do not dispose of the battery pack in
general household waste. Follow the local laws and regulations in your area for battery pack disposal.
»
The provided battery is only for this device.
»
Store the battery pack in a cool, dry place.
»
When not in use this product for a long period, remove the battery pack and store it in a cool, dry place. If you want to store it for long time, please place this product in a dry box.
Warning! Batteries may explode if not handled properly. Do not
disassemble or dispose of them in re. Keep them away from children. Follow local regulations when disposing of used batteries.
WARNING
不正確地更換電池會有爆炸的危險。僅可更換為廠商建議的相同電池或相同型 式電池。請依據廠商說明書棄置電池。
警告
用错误型号电池更换会有爆炸危险务必按照说明处置用完的电池。
注意
Revision history
Version 1.0, April 2009
iv
TABLE OF CONTENTS
CHAPTER 1 GETTING STARTED ................................................ 1
Unpacking the EM-100 ..................................................................................1
Checking the package contents ....................................................................2
Identifying components .................................................................................3
Setup the EM-100 ..........................................................................................7
Using SD cards ............................................................................................10
Install a SD card ...........................................................................................10
Viewing content of a SD card .......................................................................13
CHAPTER 2 LEARNING THE BASICS ...................................... 15
Entering text .................................................................................................15
Shortcut menus ............................................................................................15
Performing a reset........................................................................................16
Opening and closing programs ....................................................................16
Program switch ............................................................................................16
Windows CE help .........................................................................................16
Adjusting the volume ....................................................................................17
Changing the device name ..........................................................................18
Entering owner information ..........................................................................19
Recalibrating the screen ..............................................................................20
Setting the date and time .............................................................................22
Turning on / off the WLAN ............................................................................23
Turning on / off the Bluetooth .......................................................................24
Setting the screen rotation ...........................................................................25
Install and remove programs........................................................................26
Connecting to a WLAN network ...................................................................27
Automatically connect to a WLAN network ..............................................27
Manually connect to a WLAN network .....................................................27
Find an IP address ...................................................................................28
Specify the IP address and Name Servers ..............................................29
Upgrading OS Image or Bootloader .............................................................30
CHAPTER 3 USING THE ACCESSORIES ............................... 33
Attaching the leather cover .........................................................................33
v
APPENDIX .................................................................................. 35
Troubleshooting ...........................................................................................35
Tips for Troubleshooting ...............................................................................35
General Problems .......................................................................................35
Having the EM-100 Serviced ......................................................................36
Guidelines for care and maintenance ..........................................................37
Using the device ......................................................................................37
Cleaning the device .................................................................................37
Carrying or storing the device ..................................................................37
Specications ...............................................................................................38
vi
CHAPTER 1
GETTING STARTED
This chapter describes the procedures from unpacking the EM-100, to powering it on. The following topics are described.
• 1
Unpacking the EM-100 on page Checking the package contents on page • 2 Identifying components on page • 3 Setup the EM-100 on page • 7 Using SD cards on page 1• 0 Install a SD card on page 1• 0 Viewing content of a SD card on page 1• 3
Unpacking the EM-100
The device and accessories are packed in a cardboard carton with foam padding for protection during ship­ping.
EM-100
Screws
Leather cover
Figure 1.1 Unpacking the EM-100
Carefully unpack the machine and keep the packing materials. If you need to ship it in the future, repack it as shown in Figure 1.1.
Adapter
1
2 C H A P T E R 1 G E T T I N G S T A R T E D
Checking the package contents
After you unpack the device check that the following items are included.
QSG
EM-100
Stylus
CD-ROM
Quick start guide
Battery
AC adapter
Leather cover
If any item is missing or appears damaged, contact your dealer immediately.
2 screws
3
Identifying components
This section describes the parts and connectors on the EM-100.
Front panel components
2
4
1
3
Figure 1.2 Front view
Component Description
1 10.1-inch touch screen
2 Power indicator (Solid green:
power on, Solid red: battery charging, Flashing red: low
battery)
3 Bluetooch indicator (Light:
Bluetooth is functional)
5 6 7
8
Component Description
4 WiFi indicator (Light: WiFi is
functional)
5 Up selection key
6 Down selection key
7 Left selection key
8 Right selection key
4 C H A P T E R 1 G E T T I N G S T A R T E D
Top and bottom panel components
1
2
4
6
Figure 1.3 Top and bottom view
Component Description
1 Microphone
2 Left channel speaker
3 Right channel speaker
4 connector
5 connector
6 USB connector (Master mode)
3
5
5
Left and right side components
3
1
4
5 6
2
Figure 1.4 Left and right side view
Connector Description
1 Mounting holes
2 Stylus dock
3 Suspend button
4 DC power jack
5 Mini-USB connector (Slave)
6 Reset button
6 C H A P T E R 1 G E T T I N G S T A R T E D
Back panel components
1
2
1
3
Figure 1.5 Back view
Connector Description
1 Wall mount attaching holes
2 Power switch
3 Battery cover
Loading...
+ 32 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use