Parmco PW-F85-W Instruction Manual
PW-F85-W
Washing Machine Instruction Manual
■ Economic wash system
Using artificial intelligence, the washer uses minimum energy and water by selecting optimal water level and
washing time.
■ Low noise system
The washer minimizes the washing and spinning noises by sensing the amount of laundry.
■ Child·Lock
The Child-Lock system has been used to prevent children from pressing any button to change the program
during operation.
■ Steam-wash (Option)
The Steam wash system.
■ Air bubble washing (Option)
This is an advanced technology that generates millions of air bubbles inside the drum on washing sequence,
and the bubbles dissolve the detergent particles completely and cleanse all the soil in clothes gently and neatly.
■ Self-Cleaning Course of Drum
Enable to Self-Cleaning of Drum.
■ Digital Condensing Dry System.
Condensing Dry System with saving energy (for dry model).
E-2 E-3
In
A NOTE TO YOU
Thank you for buying a PARMCO appliance.
PARMCO washers are easy to use, save time, and help you manage your home better.
This manual contains valuable information about how to operate and maintain your washer properly
and safely.
- Packaging items such as plastic bags, polystrene, nails etc. that this appliance is delivered in are
potentially dangerous, and therefore appropiate measures must be taken to prevent children from
coming in contact with them.
- This appliance must only be used by adults. Make sure that children do not touch the controls or play
with the appliance. Young children should be supervised to ensure they do not play with the
appliance.
- This appliance is not intended for use by persons (including children) with physical, sensory, mental
capabilites, or lack of experience and knowledge, unless they have been given supervision or
instructions concerning the use of this appliance by a person responsible for their safety.
Parts and features ...............................................................................................................3
Washer safety ..........................................................................................................................4
InstallatIon InstructIons ..................................................................................................5
Inlet hose connectIon ..........................................................................................................6
electrIcal requIrements ....................................................................................................7
oPeratIng your Washer .......................................................................................................8
the functIons of the control Panel ...........................................................................10
WashIng Proce
dure and Program selectIon .....................................................11
guIde for other useful Programs ...............................................................................21
maIntenance ............................................................................................................................23
hoW to clean the fIlter .....................................................................................................24
removIng staIns (guIde only) ...........................................................................................25
trouBle shootIng .................................................................................................................26
sPecIfIcatIon ...........................................................................................................................27
WIrIng dIagram .......................................................................................................................28
Parts and featuresContents
Contents
E-3
Parts and featuresContents
Accessories
NOTE
The drawings in the book may vary from your washer model.
They are designed to show the different features of all models coverd by this book.
Your model may not include all features.
The parts and features of your washer are illustrated on the page.
Become familiar with all parts and features before using your washer.
INLET HOSE
HOT WATER VALVE
(OPTION)
DETERGENT CASE
DOOR
COVER PUMP
POWER CORD
CONTROL PANEL
HOSE DRAIN
Inlet hose Manual
Cap holder
(4EA)
Guide Hose Drain
(Option)
Spanner
(Option)
E-4 E-5
Installation instructionsWasher safety
Understanding your responsibilities
• Do not use chlorine bleach and ammonia or acid(such as vinegar or rust remover) in the same wash.
Hazardous fumes can form.
• Unplug power supply cord before attempting to service your washer.
• Do not wash fiberglass material.
Small particles can stick to fabrics washed in following loads and cause skin irritation.
• Do not spray water on the control panel of the washer.
It could cause fire or an electric shock.
• In case of the dual valve model, if you connect only one water inlet valve, there can be water leakage from
unconnected water inlet valve.
• This appliance must be grounded.
• To avoid electrical shock, use a metal pipe for the ground connection.
Save these instructions
Your safety is important to us.
To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the following basic
precautions.
Read all instructions before using your washer
• Flammable fluids (dry-cleaning solvents,
kerosene, gasoline, etc.) should not be used or
stored in or near your washer.
Do not add flammable fluids to your wash water.
These substances give off vapors that can create
a fire hazard or explosion.
• After starting a cycle, do not reach into the
washer until all motions stop.
• Do not tamper with the controls.
• The appliance is not intended for use by young
children or infirm persons without supervision.
• If the supply cord is damaged, it must be
replaced by the manufacturer, or its service
agent or a similarly qualified person in order to
avoid a hazard.
• If the appliance is supplied from a cord extension
set or electrical portable outlet device it should be
positioned so that it is not subjected to splashing
or ingress of moisture.
Please ...
• Have only a qualified person install, repair, or
replace parts on washer.
• Maintain washer properly.
• Protect washer from the weather and keep it
where the temperature will not fall below
freezing.
• Do not install the washer at a place of extremely
high humidity. It could cause an electric shock or
a short circuit.
• Connect washer to the correct outlet, electrical
supply, water supply, and drain supply.
El
Installation instructionsWasher safety
Removing transit bolts
Location of washer
• Check location where the washer will be installed. Make sure you have everything necessary for correct
installation.
• Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.
• Do not place or store laundry products on top of washer at any times
• Install the washer on the horizontal solid floor.
If the washer is installed on an unsuitable floor, it could make
considerable noise, vibrate severely and cause a malfunction. If the
washer is not level, adjust legs up or down for horizontal installation.
• Ventilation openings must not be obstructed by carpeting when the
washer is installed on a carpeted floor.
• Leave some space (right & left : 2cm, rear : 10cm).
• In case of built-in installation, the distance between top of the washer and
bottom of upper plate should be at least 3mm.
1. Before operating the washer, remove the transit
bolts (4ea) along with the rubber.
• If the bolts are not removed, it may cause
heavy vibration, noise and malfunction.
2. Unscrew the 4 bolts with the 10mm hex wrench
or spanner or cross-tip screwdriver. Keep the 4
bolts for a later time.
• When the appliance is transported, transit bolts
will be re-used.
3. Close the holes with the cap holders supplied.
Laundry
Tub
Washer
approx.
2cm
Drain Hose
E-6 E-7
Electrical requirementsInlet hose connection
The washer should be connected to the water mains using new hose sets and old hose sets should not be
reused.
In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the cold water
inlet valve.
Option : Be careful not to confuse hot water inlet and cold water inlet.
For Ordinary Tap (if supplied)
Pull down the collar of the inlet
hose to separate it from the
water tap adapter.
Loosen the four screws properly
in order to fit into water tap.
Fit the water tap adapter into
the water tap and tighten the
four screws evenly while
pushing up the adapter so that
the rubber packing can stick to
the water tap tightly.
Remove the tape, and screw
connector B into connect A
tightly.
Connect the inlet hose to the
water tap adapter by pulling
down the collar of the hose
end.
Connect the inlet hose adapter
of the hose to the water inlet of
the washer by turning it
clockwise to be fixed tightly.
TAPE
TAPE
TAPE
Raccorclement B
Raccorclement A
TAPE
TAPE
TAPE
• Please check the rubber packing
present inside the inlet hose
adapter of the hose.
For Screw-Shaped Tap
Connect the inlet hose to the
water tap by screwing the
connector tightly.
Connect the connector- inlet
supplied if necessary.
Connect the inlet hose adapter
to the water inlet of a washer
and turn it to be fixed.
Raccorclement B
Raccorclement A
Connector
Connector
Rubber
Packing
Hose
Connector
Rubber
Packing
Hose
Connector
inlet
TAPE
Connector
Connector
Rubber
Packing
Hose
Connector
inlet
TAPE
Connector
TAPE
*Check the washer is in the inlet
El
Electrical requirementsInlet hose connection
Drain system
• Never forget to install drain hose before operating your washer.
• Open the packing box, and there is a drain hose inside the drum.
• Connect the drain hose to the drain outlet at the back of the washer.
• Top of laundry tub must be at least 60cm high and no higher than 100cm from bottom of washer.
• When installing the drain hose to tub (sink), secure it tightly with a tie strap.
• Proper securing of the drain hose will protect the floor from damage due to water leakage.
• When the drain hose is too long, do not force it back into the washer. This will cause abnormal noise.
Level adjustment
If the washer is installed on an unsuitable
floor, it could make considerable noise,
vibrate and cause a malfunction.
Electrical shock hazard
Failure to follow these instructions could result in death or serious injury.
• Electrical earth is required on this washer
• If it does not fit the outlet, have a proper outlet
installed by a qualified electrician.
• Don’t earth to a gas pipe.
• Don’t change the power supply cord plug.
• Check with a qualified electrician if you are not
sure the washer is properly earthed.
WARNING
E-8 E-9
Electrical requirements
(cont.)
Operating your washer
Adjust the level of washer using adjustable legs.
• Please check if there is any gap between the
four adjustable legs and the floor.
• Adjust the level of washer by turning adjustable
legs. And make it sure that there
is no swaying of washer.
• After the adjustment is finished, turn the fixing
nuts up tightly so that the
washer maintains the adjustment.
Make it sure that the washer does not sway when you press down the four corners of the washer’s top
plate.
To obtain the best washing results, you must operate your washer properly.
This section gives you this important information.
Preparing clothes for washing
• Close zippers, snaps, and hooks to avoid snagging other items.
Remove pin, buckles, and other hard objects to avoid scratching the washer interior.
• Empty pockets and pull them inside out.
• Turn down cuffs and turn synthetic knits inside out to avoid pilling.
• Tie strings and sashes to avoid tangling.
• Treat spots and stains. (See “Stains” on page 25.)
Fixing Nut
adjustable leg
NOTE
There should be no swaying of washer and all the adjustable legs
should stick to the floor closely.
Operating your washer
(cont.)
Sorting
• Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together.
• Separate dark colors from light colors, colorfast items from non-colorfast item.
Loading
• Drop items into washer loosely. Items should move easily through wash water for best cleaning and wrinkle-
free results.
• Overloading the wash load can :
- Cause poor cleaning
- Increase wrinkling
- Create excessive lint
- Wear out items faster (because of pilling)
• Mix large and small items in each load.
• Reduce wash time when using a small load size setting. Loads with only a few small items needs less
wash time.
Adding detergent
Soil (Heavy, Normal, Light) Separate clothes according to amount of soil.
Color (White, Lights, Darks) Separate white clothes from colored clothes.
Lint (Lint producers,Collectors) Wash lint producers and lint collectors separately.
Detergent case
Adding fabric softener
• If desired, add measured liquid fabric softener
to the softener inlet.
• Pour liquid fabric softener into the dispenser using
the amount recommended on the package.
• Do not exceed the maximum fill line.
• Overfilling can cause early dispensing of the fabric
softener which could stain clothes.
• Do not open the detergent case when water is being
supplied.
• Avoid pouring fabric softener directly on the clothes.
• Please use only the recommended detergent for front loader washing machines.
• Please use the proper amount of detergent in conformity with the instruction of the detergent
manufacturer.
• A use of a large amount of detergent (more than the recommended amount) can cause excessive
soapsuds and overload the motor.
In addition to, this will deteriorate the washing and rinse performance.
Main wash Pre wash
Fabric softener
E-10 E-11
The functions of the control panel
Steam(option)
Water +(option)
Option
Steam(option)
Water +(option)
■ PW-F85-W
Steam(option)
Water +(option)
Press this switch to turn the power on or off.
Steam(option)
Water +(option)
Operation and temporary pausing is alternated as it is pressed.
When you want to change program in operating;
press the “Start/Pause” button → Select the program that you want to change →
press the “Start/Pause” button again.
Steam(option)
Water +(option)
You can select the programme you want, and the light is turned on when that
programme is selected.
For more detailed information, please refer to page 11~20.
Steam(option)
Water +(option)
It can be used to adjust temperature of water according to types of the load to be
washed.
As the button is pressed, temperature of water is selected by
Cold → 30°C → 40°C → 60°C → 95°C
Steam(option)
Water +(option)
By pressing the spin button, the spin speed can be chosen.
Pressing the spin button repeatedly will change the spin speed.
Steam(option)
Water +(option)
You can select the programme you want, and the light is turned on when that
programme is selected.
As the button is pressed, the wash programme is selected by
Wash → Soak → Pre-Wash
You can select the rinse+hold programme you want and the light is turned on when
that programme is selected.
It can be used to delay the washing start time by up to 12 hours.
• Is used to add a rinse, which may assist in removing traces of detergent residue.
• By selecting Rinse+ function, the rinse time and the rinse water are increased.
Use to remember your favourite programmes.
Loading...