Parkside PSTD 800 B1, 270827 Translation Of The Original Instructions

IAN 270827

JIGSAW PSTD 800 B1

JIGSAW

Translation of the original instructions

PENDULSTIKSAV

Oversættelse af den originale driftsvejledning

PENDELHUBSTICHSÄGE

Originalbetriebsanleitung

SCIE SAUTEUSE PENDULAIRE

Traduction des instructions d’origine

DECOUPEERZAAG

Vertaling van de originele gebruiksaanwijzing

GB / IE Translation of the original instructions Page 1
DK Oversættelse af den originale driftsvejledning Side 11
FR / BE Traduction des instructions d’origine Page 21
NL / BE Vertaling van de originele gebruiksaanwijzing Pagina 33
DE / AT / CH Originalbetriebsanleitung Seite 43

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
device.

Før du læser, vend begge sidene med billeder frem og bliv bekendt med alle apparatets funktioner.

Avant de lire le mode d’emploi, ouvrez les deux pages contenant les illustrations et familiarisez-vous
ensuite avec toutes les fonctions de l’appareil.

Vouw vóór het lezen de beide pagina‘s met de afbeeldingen open en maak u vertrouwd met alle functies
van het apparaat.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.

Ø 30 mm

395 mm110 mm

120 mm65 mm

205 mm

Ø 30 mm

185 mm

260 mm150 mm

30 mm

Ø 30 mm x 400 mm

PSTD 800 B1

GB│IE 

│

 1 ■

Contents

Introduction ......................................................2

Intended use ................................................................ 2

Features ................................................................... 2

Technical details ............................................................. 2

General Power Tool Safety Warnings ................................3

1. Work area safety .......................................................... 3

2. Electrical safety ........................................................... 3

3. Personal safety ............................................................ 4

4. Power tool use and care .................................................... 4

5. Service .................................................................. 5

Appliance-specific safety instructions for jigsaws .................................... 5

Original accessories/auxiliary equipment ......................................... 5

Information on saw blades ..................................................... 6

Initial operation ..................................................6

Fitting/changing the saw blade ................................................. 6

Fitting the rip fence ........................................................... 6

Connecting the sawdust extraction device ......................................... 6

Fitting the sliding shoe ........................................................ 6

Fitting the splinter guard ....................................................... 6

Adjusting the laser ........................................................... 6

Operation .......................................................7

Setting the cutting angle ....................................................... 7

Setting the stroke rate ......................................................... 7

Adjusting the pendulum stroke .................................................. 7

Switching ON/OFF .......................................................... 7

Switching the laser/working light ON/OFF ........................................ 7

Sawdust blowing function ..................................................... 7

Maintenance and cleaning ..........................................7

Kompernass Handels GmbH warranty ...............................8

Service ..........................................................9

Importer ........................................................9

Disposal .........................................................9

Translation of the original Conformity Declaration .....................10

PSTD 800 B1

■ 2 │ GB

│

IE

JIGSAW PSTD 800 B1
Introduction

Congratulations on the purchase of your new appli­ance. You have selected a high-quality product. The
operating instructions are part of this product. They
contain important information about safety, usage
and disposal. Before using the product, please
familiarise yourself with all operating and safety in­structions. Use the product only as described and for
the range of applications specified. Please also pass
these operating instructions on to any future owner.

Intended use

This appliance is suitable for straight and curved
cutting as well as mitre cuts of up to 45° on angular
workpieces made of plastic, wood or light metal. This
appliance is exclusively intended for private use in
dry indoor spaces. Observe the guidelines on saw
blade types. Any other usage of or modification to the
appliance is deemed to be improper and carries a
significant risk of accidents. The manufacturer accepts
no responsibility for damage(s) attributable to misuse.

Features

Stroke rate adjusting wheel
ON/OFF switch lock button
ON/OFF switch
Housing
Power cable
Reducer
Extraction nozzle
Footplate
Sliding shoe (removable)
Switch for sawdust blower
Pendulum stroke switch
Rip fence
Guide roller
Saw blade
Insertion openings (each incl. locking screw)
Protective bracket
Blade guard
Quick-release chuck
ON/OFF switch laser/working light
Clamping screws
Toothing
Hex key

Saw blade (for woodwork)
Saw blade (for woodwork)
Saw blade (for metalworking)
Adjusting screw
Splintering device
Notch

Package contents

1 jigsaw, incl. extraction nozzle
1 reducer
1 rip fence
3 saw blades for woodwork
1 saw blade for metalworking
1 Hex key
1 Operating instructions

Technical details

Jigsaw: Parkside PSTD 800 B1

Rated voltage: 230 V ∼ 50 Hz

(alternating current)

Rated power
consumption: 800 W

Idling stroke rate: n

0

0 - 3100 rpm
Cutting capacity: Wood/metal: 80/8 mm
Pendulum stroke: 3 stages and fine-cut setting
Oblique section: 0°/15°/30°/45° left/

right

Protection class: II /

(double insulation)

Noise emission value:

Noise measurement value determined in accordance
with EN 60745. The A-rated noise level of the
power tool is typically as follows:
Sound pressure level: L

pA

= 93 dB (A)

Uncertainty: K

pA

= 3 dB

Sound power level: L

WA

= 104 dB (A)

Uncertainty: K

WA

= 3 dB

Wear hearing protection!

Total vibration value:

(Vector total of three directions) determined in
accordance with EN 60745:

Sawing of chipboard: a

h,B

= 7.8 m/s

2

Uncertainty K = 1.5 m/s

2

Sawing of metal plate: a

h,M

= 9.8 m/s

2

Uncertainty K = 1.5 m/s

2

PSTD 800 B1

GB│IE 

│

 3 ■

NOTE

► The vibration level specified in these instruc-

tions has been measured in accordance
with the standardised measuring procedure
specified in EN 60745 and can be used to
make equipment comparisons. The specified
vibration emission value can also be used to
make an initial exposure estimate. The vibra­tion level varies in accordance with the use of
the power tool and may be higher than the
value specified in these instructions in some
cases. Regular use of the electric tool in such
a way may cause the user to underestimate
the vibration.

WARNING!

► Try to keep the vibration loads as low as pos-

sible. Measures to reduce the vibration load
are, e.g. wearing gloves and limiting the work­ing time. Wherein all states of operation must
be included (e.g. times when the power tool is
switched off and times where the power tool is
switched on but running without load).

General Power Tool

Safety Warnings

WARNING!

► Read all safety warnings and all instructions.

Failure to follow the warnings and instruc­tions may result in electric shock, fire and/or
serious injury.

Save all warnings and instructions for future
reference.

The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery­operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmos-

pheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause
you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of electric
shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will
increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

PSTD 800 B1

■ 4 │ GB

│

IE

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while

operating power tools may result in serious
personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools

with your finger on the switch or energising
power tools that have the switch on invites ac­cidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control
of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure
these are connected and properly used.

Use of dust collection can reduce dust-related
hazards.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at
the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off. Any power tool that can­not be controlled with the switch is dangerous
and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such

preventive safety measures reduce the risk of
starting the power tool accidentally.

d) Store idle power tools out of the reach of

children. Do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools diligently. Check for

misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits,

etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the

power tool for operations different from those
intended could result in a hazardous situation.

PSTD 800 B1

GB│IE 

│

 5 ■

5. Service

a) Have your power tool serviced by a qualified

repair person using only identical replace­ment parts. This will ensure that the safety of

the power tool is maintained.

Appliance-specific safety instructions
for jigsaws

■ Hold the power tool by the insulated

handles if carrying out work during which
the power tool may come into contact with
concealed power cables or its own power
cable. Contact with a live wire may electrify

exposed metal parts of the power tool and
could give the operator an electric shock.

■ Keep your hands away from the sawing area.

Do not reach underneath the workpiece. Con­tact with the saw blade may result in injury.

■ Keep your hands away from the stroke

rod and the quick-release chuck. There is

a risk of crushing if contact is made with these
components.

■ Always switch on the power tool before applying

it to the workpiece. Otherwise, there is a risk of
a kickback.

■ When sawing, ensure that the footplate

is

placed against the workpiece.

■ After completing your work, switch the power

tool off and do not pull the saw blade

out of
the cut until it has come to a complete standstill.
This prevents kickbacks, and allows you to put
the tool down safely.

■ Only use undamaged saw blades that are

in perfect working order. Bent and blunt saw
blades can break or may cause a kickback.

■ Do not try and slow the saw blade

down
after switching off by applying lateral pressure.
The saw blade might be damaged, break or
cause a kickback.

■ Secure the workpiece. Use clamps/a vice to

hold the workpiece firmly. This is safer than
simply holding it in your hand.

■ Always route the power cable towards the rear,

away from the appliance.

■ Never work on moistened materials or damp

surfaces.

■ Risks from dust! When working for extended

periods on wood and, in particular, materials
that produce dusts that are hazardous to health,
connect the appliance to an appropriate dust
extraction device.

■ Wear a dust mask!

■ Ensure there is sufficient ventilation.

WARNING! Protect yourself from

laser radiation!

LASER

2

1NBYN8tʄ: 650 nm
t&/

Never look directly into the laser beam or the
opening from which it emerges.

WARNING!

► Looking at a laser beam through optical

instruments (e.g. magnifying glasses etc.) can
cause eye injuries.

► Caution! If operating and adjustment equip-

ment or procedures other than those specified
here are used, this may result in hazardous
radiation exposure.

■ Never aim the laser beam at reflective surfaces,

people or animals. Even brief visual contact
with a laser beam can result in eye injuries.

Original accessories/auxiliary
equipment

■ Only use the accessories and additional

equipment that are specified in the operat­ing instructions and compatible with the
appliance.

PSTD 800 B1

■ 6 │ GB

│

IE

Information on saw blades

Parkside basic equipment includes saw blades
principally for use with wood and metal.

▯ 3 saw blades for general wood cuts
▯ 1 saw blade for light metals up to 3 mm

NOTE

► You can use any saw blade, provided it is

fitted with a suitable mounting (single-lug
shank).

Saw blade type

suitable unsuitable

Initial operation

Fitting/changing the saw blade

Always remove the plug from the power socket
before working on the appliance.

♦ Remove the pivoting blade guard

.

♦ Turn the quick-release chuck

and hold it in

this position.

♦ Push the required saw blade into the quick-

release chuck

as far as the limit stop.

♦ Release the quick-release chuck

so that it
returns to its initial position. The saw blade is
now locked.

■ WARNING! The saw blade teeth must point

forwards at this point (see foldout page)!

♦ Replace the pivoting guard

back onto the

appliance.

Fitting the rip fence

The rip fence can be fitted on the left or right of
the appliance.

♦ Undo both the clamping screws on the insertion

openings

.

♦ Push the rip fence

into the insertion openings .

♦ Retighten the two locking screws.

Connecting the sawdust extraction
device

♦ Push the reducer into the extraction nozzle

until it is secured.

♦ Attach an approved dust and sawdust extrac-

tor to the reducer

or extraction nozzle

directly.

Fitting the sliding shoe

When working on sensitive surfaces, you can fit
the sliding shoe on the footplate to prevent
scratching the surface.

♦ Mount the sliding shoe

onto the footplate
and press it up at the back until it clicks into
place on the footplate .

♦ To remove the sliding shoe

, unfasten it at the

rear of the footplate and slide it off the front.

Fitting the splinter guard

The splinter guard can prevent fraying of the sur­face while sawing wood . The splinter guard can
only be used for certain saw blade types, with the
sliding shoe and only for cutting angles of 0°.

♦ Press the splinter guard

from below into the
sliding shoe (arrow facing upwards).

Adjusting the laser

♦ If the laser line is not vertical in the notch , you

can adjust it by adjusting the position of screw

.

PSTD 800 B1

GB│IE 

│

 7 ■

Operation

Setting the cutting angle

♦ Undo the clamping screws with the hex

key and pull the footplate to the rear.

♦ Adjust the cutting angle to 0°/15°/30°/45°

with the aid of the markings on the footplate

.
Push the footplate to the front so that the
locking pin engages in the toothing .

♦ Retighten the clamping screws

with the Hex

key .

NOTE

► When using a cutting angle of 15°/30°/45°,

the pivoting blade guard

and splinter guard

must be detached beforehand!

Setting the stroke rate

♦ Use the stroke rate adjusting wheel to set the

required stroke rate.

Adjusting the pendulum stroke

♦ You can use the pendulum stroke switch to

adjust the pendular movement of the saw blade

. You can achieve fine, clean-cut edges with­out pendular movement (setting "0"). Deactivate
pendular movement when working on thin
workpieces. You can achieve an increasingly
fast work rate if the pendulum stroke is activated
(settings 1–3).

Switching ON/OFF

Switching the appliance on:

Press the ON/OFF switch

.

Switching the appliance off:

Release the ON/OFF switch

.

Switching to continuous operation:

Press the ON/OFF switch

and lock it in this

position with the ON/OFF switch lock button .

Switching off continuous operation:

Press the ON/OFF switch

and release it again.

Switching the laser/working light
ON/OFF

ON/OFF switch:

Press the ON/OFF switch

for the until the

required function is active.
LASER and WORKING LIGHT → WORKING

LIGHT → LASER → SWITCH OFF

Sawdust blowing function

Switching the sawdust blowing function on:

♦ Slide the sawdust blower function switch

in

the position .

Supporting the extraction function:

♦ Slide the sawdust blower function switch

in

the position “0”.

Maintenance and cleaning

WARNING! RISK OF INJURY! Switch

the appliance off and remove the
power plug before starting any work on the
appliance.

■ The appliance must always be kept clean, dry

and free from oil or grease.

■ Use a soft, dry cloth to clean the housing.

WARNING!

■ If the supply cord of this power tool is dam-

aged, it must be replaced by a specially
prepared cord available through the service
organization.

■ Replace the saw blade

as soon as its teeth

are too blunt for adequate sawing.

■ Clean the appliance after completing your

sawing work.

■ Remove any dirt (e.g. sawdust). If necessary,

clean the saw blade mount with a brush or
compressed air.

PSTD 800 B1

■ 8 │ GB

│

IE

Kompernass Handels GmbH
warranty

Dear Customer,
This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.

Warranty conditions

The validity period of the warranty starts from the
date of purchase. Please keep your original receipt
in a safe place. This document will be required as
proof of purchase.

If any material or production fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
at our discretion. This warranty service is depend­ent on you presenting the defective appliance and
the proof of purchase (receipt) and a short written
description of the fault and its time of occurrence.

If the defect is covered by the warranty, your product
will either be repaired or replaced by us. The repair
or replacement of a product does not signify the
beginning of a new warranty period.

Warranty period and statutory
claims for defects

The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord­ance with strict quality guidelines and inspected
meticulously prior to delivery.

The warranty covers material faults or production
faults. The warranty does not extend to product
parts subject to normal wear and tear or fragile
parts such as switches, batteries, baking moulds or
parts made of glass.

The warranty does not apply if the product has
been damaged, improperly used or improperly
maintained. The directions in the operating instruc­tions for the product regarding proper use of
the product are to be strictly followed. Uses and
actions that are discouraged in the operating
instructions or which are warned against must be
avoided.

This product is intended solely for private use and
not for commercial purposes. The warranty shall be
deemed void in cases of misuse or improper handling,
use of force and modifications/repairs which have
not been carried out by one of our authorised
Service centres.

Warranty claim procedure

To ensure quick processing of your case, please
observe the following instructions:

▯ Please have the till receipt and the item number

(e.g. IAN 12345) available as proof of purchase.

▯ You will find the item number on the type plate,

an engraving on the front page of the instructions
(bottom left), or as a sticker on the rear or bottom
of the appliance.

▯ If functional or other defects occur, please

contact the service department listed either by
telephone or by e-mail.

▯ You can return a defective product to us free of

charge to the service address that will be provided
to you. Ensure that you enclose the proof of
purchase (till receipt) and information about
what the defect is and when it occurred.

You can download these instructions

along with many other manuals,
product videos and software on
www.lidl-service.com.

PSTD 800 B1

GB│IE 

│

 9 ■

Service

WARNING!

■ Have the power tool repaired by the Ser-

vice centre or a qualified electrician and
only using genuine replacement parts.This

will ensure that the safety of the appliance is
maintained.

■ Always ensure that the power plug or

the mains cable is replaced only by the
manufacturer of the appliance or by an
approved customer service provider.This

will ensure that the safety of the appliance is
maintained.

NOTE

► Replacement parts not listed (such as carbon

brushes, switches) can be ordered via our
service hotline.

Service Great Britain

Tel.: [phone] (£ 0.10/Min.)
E-Mail: [e-mail]

Service Ireland

Tel.: [phone]
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
E-Mail: [e-mail]

IAN 270827

Importer

Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.

KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com

Disposal

The packaging is made from environmen-

tally friendly material and can be disposed
of at your local recycling plant.

Do not dispose of power tools in

your normal household waste!

European Directive 2012/19/EU requires that
worn-out power tools be collected separately and
recycled in an environmentally compatible manner.

Your local community or municipal authorities can
provide information on how to dispose of the worn­out appliance.

■ 10 │ GB

│

IE

PSTD 800 B1

Translation of the original
Conformity Declaration

We, KOMPERNASS HANDELS GMBH, docu­ments officer: Mr. Semi Uguzlu, BURGSTR. 21,
44867 BOCHUM, GERMANY, hereby declare that
this product complies with the following standards,
normative documents and EC directives:

Machinery Directive

&$

&.$&MFDUSPNBHOFUJD$PNQBUJCJMJUZ
&6

RoHS Directive

&6

Applied harmonised standards:

EN 60745-1:2009 / A11: 2010
EN 60745-2-11: 2010
EN 55014-1:2006 / A2: 2011
EN 55014-2:1997 / A2: 2008
EN 55014-2:2015
EN 61000-3-2: 2014
EN 61000-3-3: 2013

Type designation of machine:

Jigsaw PSTD 800 B1

:FBSPGNBOVGBDUVSF

Serial number: IAN 270827

Bochum, 04/02/2016

Semi Uguzlu

- Quality Manager ­The right to effect technical changes in the context

of further development is reserved.

PSTD 800 B1

DK 

│

 11 ■

Indholdsfortegnelse

Indledning ......................................................12

Anvendelsesområde .........................................................12

Udstyr .................................................................... 12

Pakkens indhold ............................................................12

Tekniske data .............................................................. 12

Generelle sikkerheds anvisninger til elværktøjer ......................13

1. Sikkerhed på arbejdspladsen ............................................... 13

2. Elektrisk sikkerhed ........................................................ 13

3. Personsikkerhed .......................................................... 14

4. Anvendelse og behandling af elværktøjet ......................................14

5. Service ................................................................. 15

Specielle sikkerhedsanvisninger for stiksave .......................................15

Originalt tilbehør / originalt ekstraudstyr ......................................... 16

Oplysninger om savklinger .................................................... 16

Første brug .....................................................16

Montering/udskiftning af savklinge ............................................. 16

Montering af parallelanslag ...................................................16

Tilslutning af spånudsugning .................................................. 16

Montering af glidesko ....................................................... 16

Montering af spånbeskytter ...................................................16

Finjustering af laser .......................................................... 16

Betjening .......................................................17

Indstilling af snitvinkel ........................................................ 17

Indstilling af slagfrekvens .....................................................17

Indstilling af pendulslag ......................................................17

Sådan tændes / slukkes produktet .............................................. 17

Tænd og sluk for laser-/arbejdslys ..............................................17

Spånblæsefunktion ..........................................................17

Vedligeholdelse og rengøring ......................................17

Garanti for Kompernass Handels GmbH .............................18

Service .........................................................19

Importør .......................................................19

Bortskaffelse ....................................................19

Oversættelse af den originale overensstemmelseserklæring ............20

PSTD 800 B1

■ 12 │ DK

PENDULSTIKSAV PSTD 800 B1
Indledning

Tillykke med købet af dit nye produkt. Du har valgt
et produkt af høj kvalitet. Betjeningsvejledningen
er en del af dette produkt. Den indeholder vigtige
informationer om sikkerhed, anvendelse og bort­skaffelse. Du bør sætte dig ind i alle produktets
betjenings- og sikkerhedsanvisninger før brug. Brug
kun produktet som beskrevet og kun til de angivne
anvendelsesområder. Lad vejledningen følge med
produktet, hvis du giver det videre til andre.

Anvendelsesområde

Produktet er beregnet til lige og kurvede snit samt
geringssnit på op til 45° på kantede emner i plast,
træ og letmetal. Produktet er udelukkende beregnet
til privat brug i tørre rum. Vær opmærksom på
anvisningerne vedrørende savklingetyper. Enhver
anden anvendelse eller ændring af produktet an­ses for at være uden for anvendelsesområdet og
indebærer betydelige farer for uheld. Producenten
påtager sig intet ansvar for skader, der opstår som
følge af anvendelse uden for anvendelsesområdet.

Udstyr

Indstillingshjul til forvalg af slagfrekvens
Låseknap tænd-/sluk-knap
TÆND-/SLUK-knap
Hus
Ledning
Reduktionsstykke
Udsugningsstuds
Bundplade
Glidesko (aftagelig)
Kontakt til spånblæseanordning
Pendulslagkontakt
Parallelanslag
Føringsrulle
Savklinge (til træforarbejdning)
Indføringsåbninger (inkl. stopskrue)
Beskyttelsesbøjle
Beskyttelsesafdækning
Hurtigskiftepatron
TÆND-/SLUK-knap til laser-/arbejdslys
Klemskruer
Fortanding
Unbrakonøgle
Savklinge (til træforarbejdning)
Savklinge (til træforarbejdning)

Savklinge (til metalforarbejdning)
Finjusteringsskrue
Spånbeskytter
Not

Pakkens indhold

1 pendulstiksav inkl. udsugningsstuds
1 reduktionsstykke
1 parallelanslag
3 savklinger til træforarbejdning
1 savklinge til metalforarbejdning
1 sekskantnøgle
1 betjeningsvejledning

Tekniske data

Pendulstiksav: Parkside PSTD 800 B1

Mærkespænding: 230 V ~, 50 Hz

(vekselstrøm)
Mærkeeffekt: 800 W
Tomgangsslagfrekvens: n

0

0 - 3100 min

-1

Skæredybde: Træ/metal: 80/8 mm
Pendulslag: 3 trin og indstilling af fin-

snit
Skråsnit: 0°/15°/30°/45°

venstre/højre
Beskyttelsesklasse: II /

(dobbeltisolering)

Støjemissionsværdi:

Måleværdi for støj beregnet iht. ENISO 60745.
Det A-vægtede støjniveau for elværktøjet er typisk
som følger:

Lydtryksniveau: L

pA

= 93 dB (A)
Usikkerhed KpA = 3 dB
Lydeffektniveau: LWA = 104 dB (A)
Usikkerhed: K

WA

= 3 dB

Bær høreværn!

Samlede vibrationsværdier:

(vektorsum i tre retninger) beregnet iht. EN60745:
Savning af spånplader a

h,B

= 7,8 m/s

2

Usikkerhed K = 1,5 m/s

2

Savning af metalplader a

h,M

= 9,8 m/s

2

Usikkerhed K = 1,5 m/s

2

PSTD 800 B1

DK 

│

 13 ■

BEMÆRK

► Vibrationsniveauet, som er angivet i disse an-

visninger, er målt med en målemetode, der er
standardiseret efter EN60745, og som kan
anvendes til sammenligning af elværktøjer.
Den angivne vibrationsemissionsværdi kan
også anvendes til en indledende vurdering
af faren ved vibrationsniveauet. Vibrationsni­veauet ændrer sig afhængigt af elværktøjets
anvendelse og kan i mange tilfælde ligge
over værdien, der er angivet i disse anvisnin­ger. Vibrationsbelastningen kan undervur­deres, hvis elværktøjet jævnligt anvendes på
denne måde.

ADVARSEL!

► Prøv at holde belastningen på grund af

vibrationer så lav som muligt. Vibrationsbe­lastningen kan f.eks. reduceres ved brug af
handsker under anvendelse af værktøjet samt
ved nedsættelse af den tid, hvor værktøjet
bruges. Der skal tages hensyn til hele drifts­cyklussen (f.eks. perioder, hvor elværktøjet er
slukket, og perioder, hvor det er tændt, men
kører uden belastning).

Generelle sikkerheds-

anvisninger til
elværktøjer

ADVARSEL!

► Læs alle sikkerhedsanvisninger og -instruktio-

ner. Hvis de angivne sikkerhedsanvisninger
og -instruktioner ikke overholdes, kan det
medføre elektrisk stød, brand og/eller alvor­lige kvæstelser.

Opbevar sikkerhedsanvisningerne og -in­struktionerne til senere brug.

Begrebet “elværktøj”, der anvendes i sikkerheds­anvisningerne, henviser både til elværktøj, der
anvendes med ledning til lysnettet, og batteridrevet
elværktøj (uden strømledning).

1. Sikkerhed på arbejdspladsen

a) Hold arbejdspladsen ren og godt oplyst. Rod

og dårligt oplyste arbejdspladser kan medføre
uheld.

b) Arbejd aldrig med elværktøj i eksplosionsfar-

lige omgivelser, hvor der befinder sig brænd­bare væsker, gasser eller støv. Elværktøj danner

gnister, som kan antænde støvet eller dampene.

c) Hold børn og andre personer på afstand, når

elværktøjet bruges. Hvis du bliver distraheret,
kan du miste kontrollen over produktet.

2. Elektrisk sikkerhed

a) Elværktøjets tilslutningsstik skal passe til stik-

kontakten. Stikket må ikke ændres på nogen
måde. Der må ikke bruges adapterstik sam­men med beskyttelsesjordet elværktøj. Uæn-

drede stik og de rigtige stikkontakter reducerer
risikoen for elektrisk stød.

b) Undgå kropskontakt med jordforbundne

overflader som f.eks. rør, radiatorer, komfurer
og køleskabe. Der er øget risiko for elektrisk

stød, hvis din krop har jordforbindelse.

c) Hold elværktøjet væk fra regn og fugt. Hvis der

trænger vand ind i elværktøjet, øges risikoen for
elektrisk stød.

d) Brug ikke ledningen til noget, den ikke er

beregnet til, f.eks. til at bære eller hænge
værktøjet op i eller til at trække stikket ud af
stikkontakten. Hold ledningen på afstand af
varme, olie, skarpe kanter eller produktets
bevægelige dele. Beskadigede eller sammenfil-

trede ledninger øger risikoen for elektrisk stød.

e) Hvis du anvender elværktøj udendørs, skal

der bruges en forlængerledning, som er god­kendt til brug udendørs. Når du anvender en

forlængerledning, der er beregnet til udendørs
brug, reduceres risikoen for elektrisk stød.

PSTD 800 B1

■ 14 │ DK

f) Hvis det ikke er muligt at undgå at bruge

elværktøjet i fugtige omgivelser, skal der
installeres en fejlstrømsafbryder. Installation

af en fejlstrømsafbryder reducerer risikoen for
elektrisk stød.

3. Personsikkerhed

a) Vær altid opmærksom og bevidst om, hvad

du laver, og arbejd fornuftigt med elværktø­jet. Brug ikke elværktøjet, hvis du er ukoncen­treret eller påvirket af narkotika, alkohol eller
medicin. Selv et øjebliks uopmærksomhed ved

brug af elværktøjet kan medføre alvorlige kvæ­stelser.

b) Brug personligt beskyttelsesudstyr, og bær

altid beskyttelsesbriller. Når du bruger person­ligt beskyttelsesudstyr som f.eks. støvmaske, skrid­sikre sikkerhedssko, beskyttelseshandsker, sikker­hedshjelm og høreværn afhængigt af elværktøjets
type og anvendelse, reduceres risikoen for kvæ­stelser.

c) Undgå utilsigtet igangsætning. Kontrollér, at

elværktøjet er slukket, før du forbinder det
med strømforsyningen og/eller tilslutter bat­teriet, tager elværktøjet op eller bærer det.

Hvis du har en finger på kontakten, eller hvis
elværktøjet er tændt, mens du bærer det, kan
der opstå uheld.

d) Fjern indstillingsværktøj eller skruenøgler,

før du tænder elværktøjet. Hvis der sidder et
værktøj eller en skruenøgle på en roterende del
af elværktøjet, kan det medføre personskader.

e) Undgå unormale kropsstillinger. Sørg for,

at du står sikkert, og hold altid balancen.
Derved kan du bedre kontrollere elværktøjet i
uventede situationer.

f) Bær velegnet påklædning. Bær ikke løstsid-

dende tøj eller smykker. Hold hår, tøj og
handsker på afstand af dele, der bevæger
sig. Løst tøj, smykker eller hår kan gribe fat i

dele, der bevæger sig.

g) Hvis der monteres opsugnings- og opsam-

lingsanordninger, skal disse tilsluttes og
anvendes korrekt. Anvendelse af denne type

anordninger nedsætter støvrisikoen.

4. Anvendelse og behandling af

elværktøjet

a) Overbelast ikke elværktøjet. Brug et elværk-

tøj, der er egnet til arbejdet. Du arbejder bedre

og mere sikkert i det angivne effektområde, hvis
du bruger det rigtige elværktøj.

b) Brug ikke elværktøj med defekt kontakt.

Elværktøj, som ikke længere kan tændes og
slukkes, er farligt og skal repareres.

c) Træk stikket ud af stikkontakten og/eller fjern

det genopladelige batteri, før du indstiller
elværktøjet, tilbehørsdelene eller lægger
elværktøjet fra dig. Disse forholdsregler forhin-

drer, at elværktøjet starter ved en fejl.

d) Opbevar elværktøj uden for børns række-

vidde, når værktøjet ikke anvendes. Personer,
som ikke kender produktet, eller som ikke har
læst disse anvisninger, må ikke bruge produk­tet. Elværktøj er farligt, hvis det anvendes af

uerfarne personer.

e) Vedligehold elværktøjet omhyggeligt.

Kontrollér, om bevægelige dele fungerer, som
de skal og ikke sætter sig fast, om dele er
defekte eller så beskadigede, at elværktøjets
funktion er påvirket. Få beskadigede dele
repareret, inden du bruger produktet. Mange

uheld skyldes dårligt vedligeholdt elværktøj.

f) Hold skærende værktøjer skarpe og rene.

Omhyggeligt vedligeholdt værktøj med skarpe
skær sætter sig ikke så ofte fast og er lettere at
styre.