Park Flite Mirage 2000 Instruction Manual

2

Mirage 2000

RTF Model

INSTRUCTION MANUAL

Top Gun Park Flite are proud to present this high
performance ducted fan sport scale model of the
Mirage 2000 We feel that this model emulates the
style, performance and character of its full size
counterpart.

Supplied as a Ready to Fly package with transmitter,
LiPo flight battery and charger, ARTF or Airframe
only, this model has been designed with the utmost
care and attention to detail to produce a light
weight, strong, and realistic looking model
aeroplane with excellent flying characteristics.
This model is a high performance miniature aircraft
that allows intermediate to advanced model pilots to
perform both scale and aerobatic manoeuvers. The
light weight, large wing area and delta wing design
allow the model to fly both fast and slow, with high
speed rolls and tight turns while maintaining full
control.
These instructions assume a reasonable level of
competence for both building and flying and we
recommend that the model is flown at a recognised
club with frequency control measures and suitable
third party insurance.

The owner – pilot of this model should take note of
regulations, and local bylaws before flying this
aircraft.
Please take time to read through these instructions
before commencing assembly. We list operations in
order of works to reduce the risk of damage during
assembly.

Please read through the warnings before use.
A 11.1V 1300 mAh lithium polymer (LiPo) battery and
charger is included as part of this package and
these cells must be operated with care to prevent
the risk of fire.
LiPo Batteries are soft cased and can be easily
damaged by sharp items, puncturing of the soft
casing can cause fires and we recommend that they
are stored and handled carefully.
Use only a LiPo rated charger, set to a maximum of 3
cells (11.1v) and no more than 1 amp charge
current.
Remove battery from the aircraft and charge on a
non flammable, non conductive surface
Due to continual and ongoing product development
the parts shown in the manual may differ from those
supplied.

Congratulations on purchasing the Mirage 2000 RTF

3

Fuselage with ducted fan, motor, Electronic
Speed Control (ESC) receiver, rudder- steering
servo, pushrods and nose wheel.

Two delta wing panels with ailerons connected to
factory installed servos

Forward stabiliser canards (2 off)

Rear fin strake/ ECM Antennae

2 Main undercarriage assemblies with wheels
and mounting hardware

4 function fully proportional 35Mhz transmitter

Adjustable quick release neck strap for
transmitter

Tube of adhesive

LiPo Battery 3 cell 11.1V 1300 mAh (15c)

2- 3 cell balance type 800mAh LiPo charger and
12v power lead

KIT CONTENTS AND DESCRIPTION

SPECIFICATIONS

Wing span: 680mm (26.75”)
Length: 980mm (38.5”)
Wing Area: 13 Dm

2

(200 sq inches)
Weight: 565 g (20 Ounces)
Radio: 4 function 35Mhz PPM

3 Qty micro servos
25 Amp brushless ESC

Motor: Brushless in runner

5 blade ducted fan

11.1v 1300mAh LiPo battery

4

FUSELAGE ASSEMBLY.

Supplied complete and ready for use with ducted
fan unit using high performance brushless in
runner motor.

25Amp Electronic Speed Control (ESC) prewired to
motor with extended leads to forward battery box
and hinged cover.

Sprung steerable nose wheel assembly.

35mhz 8 channel receiver pre-wired to ESC and
rudder-steering servo with extension leads to each
wing.

Smoked canopy
over cockpit with
profile pilot.

Nose cone
supplied loose.

WING ASSEMBLY.

Supplied as two halves.

Each wing half includes undercarriage fixing plates
and hinged aileron control surfaces.

Wing mounted aileron servos connect to control
horn with pushrods and snap link clevis connector.

MAIN UNDERCARRIAGE ASSEMBLIES.

Two sets of lightweight wheels fixed onto wire
torque rod undercarriage.

Four clamp plates and 8 fixing screws for securing
to wing plates.

Steerable nose gear is pre fitted to fuselage.

Two forward canard surfaces for sides of intake
ducts.

One Fin strake / ECM antennae for mounting near
top of fin.