Page 1
1030
178
WARNING
Read and understand these Instructions
for Use and all safety precautions it
contains. Improper use can cause serious
or fatal injury and/or illness.
CAUTION––US Federal law restricts this
device to sale by or on order of a physician.
Page 2
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
|
2
www.pari.com/register
1.866.335.6943
Registration card enclosed
REGISTER FIRST
WARRANTY ACTIVATION REQUIRED
Three dierent options to choose from.
Conforms to UL 60601-1
Certied to CAN/CSA C22.2 No. 601.1
ETL CLASSIFIED
Intertek
3045080
Page 3
3
|
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
TABLE OF CONTENTS
A Introduction .............................................................................. 3
B Safety Precautions And Important Safeguards ............. 4-5
C Getting Started ......................................................................... 6
D Using “AA” Batteries ................................................................ 7
E Using AC Power Supply ............................................................ 7
F eRapid Nebulizer Handset Assembly ............................... 8-9
G Taking A Treatment ..........................................................1 0-11
H eRapid Nebulizer Handset Cleaning ............................. 12-13
I Using the Optional EASYCARE ..............................................14
J eRapid Nebulizer Handset Disinfection .............................14
K Functionality Test ..................................................................15
L Frequently Asked Questions And Troubleshooting .........15
M Specications ........................................................................16
A INTRODUCTION
These Instructions For Use contain information and safety
precautions for the eRapid™ Nebulizer System. Save these
Instructions For Use for future reference.
Before using your eRapid Nebulizer System, you should read and
understand the entire Instructions For Use. If for any reason you do
not understand any part of these Instructions For Use, please call
the toll free number below before proceeding with your treatment.
Take special note of all safety precautions marked DANGER
and WARNING.
INDICATIONS FOR USE: ERAPID NEBULIZER SYSTEM
The eRapid Nebulizer System is to be used with patients for whom
doctors have prescribed medication for nebulization. It is intended
for adult and pediatric patients, and may be used in hospitals,
hospital-type facilities, nursing homes, sub-acute institutions and
home environments.
Page 4
READ ALL DANGERS AND WARNINGS BEFORE USING
DANGER
To reduce the risk of serious or fatal injury from electrocution:
1. DO NOT place or store the eRapid Nebulizer System where
it can be in water or fall into a bathtub, sink, or other liquid.
Do not place or drop into water or other liquid. Do not use
while bathing.
2. DO NOT reach for the eRapid Nebulizer System if it has
fallen into water or other liquid. Unplug immediately.
Retrieve the eRapid Nebulizer System ONLY after it has
been unplugged.
WARNING
1. The eRapid Nebulizer Handset is for single patient use. DO
NOT SHARE your handset with any other people.
2. Read, understand and follow all warnings and instructions
in the Instructions For Use prior to using this device.
3. To reduce the risk of serious or fatal injury from
electrocution, re, burns and to reduce the risk of damage
and malfunction of the unit:
a. DO NOT overload wall outlets or use extension cords.
b. Keep all electrical cords away from heated surfaces.
c. DO NOT spray liquids onto the housing of the Control-
ler. (See Section C: Getting Started) Liquid may cause
damage to the electrical parts and could lead to a
malfunction. In the event that liquids enter the Controller, call the number below.
d. DO NOT drop or insert any object into any opening on
the eRapid Nebulizer System.
e. DO NOT operate where oxygen is being administered in
a closed environment such as an oxygen tent.
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
|
4
B SAFETY PRECAUTIONS AND IMPORTANT SAFEGUARDS
4. Always unplug this product immediately after using and
before cleaning.
5. Before use, check your eRapid Nebulizer System or eRapid
Nebulizer Handset for proper assembly. All parts must
be connected and rmly in place. Use of an improperly
assembled eRapid could diminish or eliminate the
eectiveness of the treatment.
6. Use ONLY adapters and accessories that are authorized for
the eRapid Nebulizer System. Use of unapproved adapters
and accessories can lead to improper treatment, injury, or
damage to the Controller.
7. The eRapid Handset has unique performance
characteristics and should NEVER be substituted for
other eFlow Technology Handsets (e.g. Altera®, TRIO®,
Investigational eFlow®).
8. NEVER use the eRapid Aerosol Head with any other eFlow
Technology Handset (e.g. Altera, TRIO, Investigational
eFlow). The eRapid Aerosol Head has its own, unique
performance characteristics.
9. NEVER operate the Controller if it is improperly or
incompletely assembled or damaged. Section G: Taking
A Treatment, shows the alerts to these situations when
the eRapid Nebulizer System is improperly assembled, or
might be damaged.
10. NEVER operate this product if:
a. it has damaged cords or plugs,
b. it is not working properly,
c. it has been dropped or damaged, or
d. it has been exposed to any liquids inside the Controller.
Continued on page 5
Page 5
5
|
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
B SAFETY PRECAUTIONS AND IMPORTANT SAFEGUARDS
WARNING
11. To reduce the risk of infection, illness, and/or injury from
contamination, clean and dry all parts of the eRapid
Nebulizer Handset after each treatment. Follow the
instructions in Section H to clean the eRapid Nebulizer
Handset properly.
12. Cleaning the eRapid Nebulizer Handset properly will help
prevent the Aerosol Head from clogging. If the Aerosol
Head becomes clogged, the aerosol mist will be reduced
or stopped, which may make the treatment ineective. If
clogging occurs, use the instructions in Section H to clean
the Aerosol Head.
13. Cleaning the eRapid Nebulizer Handset only removes the
medication. To reduce the risk of serious or fatal illness
caused by contamination of the eRapid Nebulizer Handset,
YOU MUST ALSO DISINFECT THE eRapid NEBULIZER
HANDSET AT THE END OF EVERY TREATMENT DAY. See
Section J for disinfection instructions.
14. This product contains small parts that may present a
choking hazard to small children. The eRapid Nebulizer
Connection Cord also presents a strangulation hazard.
15. DO NOT LEAVE CHILDREN UNATTENDED DURING
TREATMENT. ALWAYS USE CLOSE ADULT SUPERVISION WHEN
ADMINISTERING A TREATMENT TO A CHILD.
16. Keep the eRapid Nebulizer Handset level when in use. If
the handset is tilted, the dosage may not be accurate.
17. Close supervision is necessary when this product is used
by or near children or the physically or mentally impaired.
18. DO NOT use your eRapid Nebulizer System while driving or
in any situation which takes away your full attention.
19. If the eRapid Nebulizer System has been damaged or is
not operating properly, call the number below for details.
If you suspect that the eRapid Nebulizer System has been
damaged or is not working correctly, run the Functionality
Test described in Section K.
20 . DO NOT disassemble the Controller at anytime. There are
no user serviceable parts inside the Controller. Call the
number below for all service needs.
Page 6
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
|
6
C GETTING STARTED
Check your eRapid Nebulizer System package to ensure you have
the following items. Note that two complete Nebulizer Handsets
are included.
FOUR “AA” BATTERIES
NEBULIZER CONNECTION CORD
EBASE CONTROLLER
AEROSOL CHAMBER
MOUTHPIECE WITH
EXHALATION VALVE
AC POWER SUPPLY
AEROSOL HEAD
INHALATION VALVE
CARRYING CASE
MEDICATION CAP
(NOTE: THE CAP SEAL AND
CAP WILL COME AS ONE
ASSEMBLED PART)
CAP SEAL
MEDICATION RESERVOIR
Page 7
PLUG CONVERTER
BATTERY DOOR
PLUG INSERT
PLUG INLET PORT
CONTROLLER
BATTERY DOOR
7
|
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
D USING “AA” BATTERIES
1. The eRapid Nebulizer System is designed to be used with
“AA” batteries or with the optional AC Power Supply. Four (4)
new “AA” batteries will provide approximately 90 minutes of
continuous treatment. You may also use “AA” rechargeable
batteries. Please see “Specications” on the back cover of
these Instructions For Use.
NOTE: IT IS STRONGLY RECOMMENDED TO HAVE AN EXTRA
BATTERY SET WITH YOU AT ALL TIMES.
2. Open the Battery Door on the Controller by placing your thumb
on the tab of the Battery Door and rmly pushing the tab to
open the door (Figure 1).
NOTE: The Battery Door is designed to have a tight t. Questions?
Please call the number below.
3. Load the batteries.
4. Each battery chamber has a small gure that shows the
proper position of each battery (Figure 2). Using the battery
“tips” as guides and starting left-to-right, insert the batteries:
Tip Out, Tip In, Tip Out, Tip In.
5. To close the Battery Door, push it closed until you hear it “click”
into place. NOTE: Rechargeable and Disposable Batteries vary
considerably in terms of storage life and output. An operating
life of 90 minutes of use is based on disposable batteries that
meet the specications listed in “Specications” on the back
cover of these Instructions For Use.
E USING AC POWER SUPPLY
1. The Controller can also be used with the AC Power Supply. The
AC Power Supply is useful as a back-up power supply when the
batteries are depleted. If not already attached, insert the Plug
Converter into the AC Power Supply as shown (Figure 3).
2. The AC Power Supply (Figure 3) can be used with 100-240V
outlet and will automatically adjust to the incoming voltage. It
can be used worldwide, but does require “Plug Converters” for
use outside the USA. Additional Plug Converters for the eRapid
Nebulizer System are available as optional accessories. Make
sure to use the correct Plug Converter for the AC outlet.
3. To connect the AC Power Supply to the Controller, place the
Controller on a at, stable surface. Push the Plug Insert (the
round end of the AC Power Supply cord) into the Plug Inlet Port,
located on the under side of the Battery Door. (Figure 4). Do
not attempt to insert the AC Power Supply Cord into the front of
the Controller.
4. Plug the AC Power Supply into the wall outlet.
NOTE: Prior to storing the device over an extended period of time
(e.g., over 30 days) we recommend you remove the four batteries
from the Controller. Doing so saves the batteries and reduces the
risk of battery leakage.
Figure
1
Figure
3
Figure
2
Figure
4
Page 8
INHALATION VALVE
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
|
8
F ERAPID NEBULIZER HANDSET ASSEMBLY
WARNING
The eRapid Nebulizer Handset is not sterile. Clean and
Disinfect the eRapid Nebulizer Handset before the
rst use. (see Section H for Cleaning and Section J for
Disinfecting). Inspect all parts to ensure they are clean and
are not visibly damaged. Do not use dirty or damaged parts.
1. The Medication Reservoir and the Aerosol Chamber are
attached using a “hinge”. First, gently pull up on the tab of the
Medication Reservoir (Figure 5a). This will release the Aerosol
Chamber so that you may open it (Figure 5b). Ensure that the
Inhalation Valve is placed correctly in the Aerosol Chamber. If
not, re-insert as shown (Figure 6a-6b).
2. Ensure that the Aerosol Head is inscribed “eRapid” (Figure 7,
enlargement). Do not use other eFlow
®
Technology Aerosol
Heads in this device. Additionally, do not use the eRapid
Aerosol Head in other eFlow Technology Handsets (e.g. Altera,
TRIO, Investigational eFlow). Being careful to touch ONLY the
plastic outer ring of the Aerosol Head (Figure 7), press the
two exible plastic tabs on the side of the Aerosol Head while
rmly inserting it into the Medication Reservoir (Figures 7a7b). You should feel the plastic tabs “grab” as you insert it. It is
important that you do not touch the metal part of the Aerosol
Head (Figure 8).
3. Close the eRapid Nebulizer Handset by pushing the Aerosol
Chamber together with the Medication Reservoir until you
hear a slight “snap” (Figure 9). If you do not hear a slight
snap, open the eRapid Nebulizer Handset and ensure that the
Inhalation Valve is seated properly (Figure 6b).
4. Attach Mouthpiece to Nebulizer Handset with Exhalation Valve
facing up (Figure 10).
5. Align the hinge part of the eRapid Nebulizer Connection Cord
with the rear underside of the eRapid Nebulizer Handset
(Figure 11a), then snap it into place (Figure 11b).
6. Place the Controller on a clean, at, stable surface.
7. Connect the Nebulizer Connection Cord round end to the front
of the Controller (Figure 12).
Figure
5
Figure
6a
Figure
6b
a
b
TAB
INHALATION VALVE
Page 9
9
|
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
Figure
7
Figure
9
Figure
10
Figure
11
Figure
12
Figure
8
Figure
7a
Figure
7b
AEROSOL HEAD DETAIL
TABS
EXHALATION VALVE
a
b
Page 10
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
|
10
G TAKING A TREATMENT
1. Make sure the eRapid Nebulizer Handset is on a at,
stable surface.
2. Pour only the medication prescribed by your physician
specically for the eRapid Nebulizer System into the eRapid
Nebulizer Handset Medication Reservoir (Figure 13). DO NOT
USE MEDICATIONS PRESCRIBED FOR OTHER NEBULIZERS IN THE
ERAPID NEBULIZER SYSTEM. NOTE: THE MAXIMUM VOLUME FILL
IS 6 ML. DO NOT OVERFILL THE MEDICATION RESERVOIR.
3. Align the Tabs on the Medication Cap with the Tab Slots on the
Medication Reservoir (Figure 14a). Turn the Medication Cap
clockwise until it stops (Figure 14b). Your eRapid Nebulizer Handset
is now ready, and you can begin your treatment (Figure 15).
4. To begin your treatment, sit in a relaxed, upright position. Press
and hold the On/O button for a few seconds (Figure 16). You
will hear one “beep” and the status light will illuminate green.
The eFlow Technology logo will appear. This is the START screen.
(Figures 16-17c). The Controller is now ON.
5. After a few seconds, aerosol mist will begin to ow into the
Aerosol Chamber of the eRapid Nebulizer Handset.
6. Your Controller is designed to display the TREATMENT screen
(Figure 17b) if the eRapid Nebulizer System is assembled
correctly and working properly.
7. Place the Mouthpiece on top of your bottom lip and tongue and
close your lips around it. Hold the eRapid Nebulizer Handset level.
If held down more than 45 degrees, the Aerosol Head will emit
2 beeps and the status light on the Controller will ash 2 green
lights. After approximately 30 seconds the Controller will shut o.
If this occurs, hold the eRapid Nebulizer Handset level and press
the Controller’s On/O Button to resume the treatment.
WARNING
Keep the eRapid Nebulizer Handset level when in use. If the
handset is tilted, the dosage may not be accurate.
8. Breath normally in and out through the Mouthpiece. Continue to
inhale and exhale comfortably until the treatment is nished.
9. When all of the medication has been delivered you will hear
the Aerosol Head emit 2 beeps, the DOSE COMPLETE screen will
appear (Figure 18), and the Controller will automatically shut o.
10. The eBase Controller included with the eRapid includes software
that allows a PAUSE, when necessary. If for any reason you
must PAUSE in your treatment before its completion, press
and hold the Controller’s On/O Button for one full second. The
eRapid’s PAUSE mode is activated when the LED ashes GREEN
and your Controller display switches from the TREATMENT
screen to the PAUSE screen (Figure 17c). When you are ready
to resume your treatment, press and hold the Controller On/O
Button for one full second. The treatment will then resume, with
the Controller display switching from the PAUSE screen to the
TREATMENT screen.
Figure
13
Figure
14
Figure
15
MEDICATION RESERVOIR
a
b
TAB
TAB SLOT
NOTE: eBase Controllers supplied with other eFlow Technology
devices may not have this software feature.
11. The Controller will shut o automatically at the end of the
treatment. Unique to the eRapid Nebulizer Handset design is
about 1mL (or 1/5 teaspoon) of residual volume of medication
which mimics other general purpose nebulizers intended to
deliver approved medications. Open the Medication Cap and check
to make sure that there is not more than 1 mL of medication
following a complete treatment. If there is, replace the Medication
Cap and resume the treatment until only about 1mL remains in
the Medication Reservoir (Fig. 19).
12. Once the treatment is complete, disassemble the eRapid
Nebulizer Handset for cleaning. Refer to Section H for
cleaning instructions.
Page 11
11
|
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
Figure
17a
Figure
17b
Figure
17c
Figure
18
Figure
19
Figure
16
MESSAGE SCREENS-CORRECT ASSEMBLY
NOTE: When the dose is complete the Aerosol Head will emit 2
beeps, the DOSE COMPLETE screen will appear (Figure18), and
the Controller will automatically shut off.
PAUSE SCREEN
(Battery)
TREATMENT SCREEN
(Battery)
TREATMENT SCREEN
(AC Adapter)
START SCREEN
PAUSE SCREEN
(AC Adapter)
MESSAGE SCREENS & WARNINGS
NOTE: Your Controller has an LCD screen that provides
information to you. Think of these screens as “electronic
coaching” to ensure proper operation of the eRapid Nebulizer
System. Symbols on the screen will “alternate”as shown below.
In addition, the Controller status light NEAR THE ON/OFF BUTTON
will ash red-green and repetitive alarm beep tones will sound.
When the alternating screens appear, follow the text in the
“Description/Remedy” to the right of the screen symbols below.
SYMBOL (ALTERNATING SCREENS) DESCRIPTION/REMEDY
BATTERY LEVEL LOW.
Replace with New Batteries
Immediately OR Use AC Power
Supply
PAUSE Mode
Replace with New Batteries
Immediately OR Use AC Power
Supply
EASYCARE Mode
Replace with New Batteries
Immediately OR Use AC Power
Supply
INCORRECT ASSEMBLY.
Check Nebulizer Connection
Cord to Controller.
Check Nebulizer Connection
Cord to Nebulizer Handset.
NO MEDICATION DETECTED IN
MEDICATION RESERVOIR.
Fill Medication Reser voir OR
Hold The eRapid Nebulizer
Handset Level and Press The
On/O Button.
BATTERIES ARE EMPTY.
Replace with New Batteries
Immediately OR Use AC Power
Supply.
CAUTION SCREEN.
Device will shut down.
Call 1-866-335-6943.
NOTE: After all fault screens have been remedied, the START
screen will re-appear (Figure 17a) and the treatment can resume.
DOSE COMPLETE
Clean Your eRapid
Nebulizer Handset
STATUS LIGHT
Page 12
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
|
12
Figure
20
Figure
21
a
b
a
b
Never use a brush or any other object to clean the Aerosol
Head (Figure 28). THOROUGH RINSING OF BOTH SIDES OF THE
AEROSOL HEAD HELPS TO PREVENT CLOGGING AND ENSURE
PROPER OPERATION.
4. Following Step 3, rinse the front and back of the Aerosol
Head for about 1 minute under warm running tap water
(about 104° F) (Figure 27).
5. Rinse all eRapid Handset parts thoroughly under running,
warm tap water. After rinsing shake all parts to remove
excess water.
If Disinfecting after Cleaning, skip to Section I and follow
the steps.
6. Air dry the eRapid Nebulizer Handset parts on a clean,
lint-free towel.
7. After the eRapid Nebulizer Handset parts are completely
dry, place them in a bag for storage. DO NOT re-assemble the
eRapid Nebulizer Handset until just prior to the next treatment.
This is to ensure that the silicone seals do not become warped
over time.
8. If the eBase Controller needs cleaning, wipe down with a
slightly damp, soft cloth. DO NOT allow liquid to get inside
the Controller.
H ERAPID NEBULIZER HANDSET CLEANING
WARNING
To reduce the risk of infection, illness, and/or injury
from contamination and/or improper use, clean the
eRapid Nebulizer Handset as soon as possible after
your treatment. Do not wash the Controller, Nebulizer
Connection Cord, AC Power Supply or Plug Converters. Use
liquid soap designed for washing dishes. Do not use “white”
liquid dish soaps (e.g. Ivory or Dove) or antibacterial liquid
dish soaps as these may contain additives harmful to the
eRapid Nebulizer Handset. Also:
• Do not put the Aerosol Head in a microwave oven.
• Do not attempt to clean the Aerosol Head in a dishwasher.
• Mechanical cleaning of the Aerosol Head with brushes or
abrasives may cause irreparable damage.
NOTE: The cleaning instructions described may be used in both
home and institutional environments.
1. Disconnect the eRapid Nebulizer Handset from the Nebulizer
Connection Cord (Figures 20a and 20b).
2. Disassemble the eRapid Nebulizer Handset parts:
a. Remove the Medication Cap from the Medication Reservoir
(Figure 21). Dispose of the residual medication (about 1
mL) from the Medication Reservoir in accordance with the
drug manufacturer’s guidelines.
b. Remove the Mouthpiece from the Aerosol Chamber
(Figure 22).
c. Gently pull up on the tab of the Medication Reservoir. This
will release the Aerosol Chamber so that you may open it
(Figure 23).
d. Remove the Inhalation Valve from the Aerosol Chamber
(Figure 24).
e. Being careful to touch ONLY the plastic outer ring of the
Aerosol Head, press the two exible plastic tabs on the
side of the Aerosol Head and remove the Aerosol Head
(Figures 25-26).
NOTE: There is no need to disassemble the Medication Reservoir
from the Aerosol Chamber either for Cleaning or Disinfecting.
Doing so may damage the hinge that holds them together.
3. Place all eRapid Nebulizer Handset parts as well as the
Aerosol Head in warm (about 104º F) tap water with a little
dish washing soap (dosage according to the manufacturer’s
instructions) for 5 minutes (Figure 29). Move the parts
around in the soapy water a few times. A soft brush (e.g. a
new, unused toothbrush) can be used on all parts to aid with
cleaning EXCEPT the Aerosol Head.
Page 13
13
|
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
Figure
22
Figure
23
Figure
26
Figure
27
Figure
28
Figure
29
Figure
24
Figure
25
TAB
a
b
a
b
Page 14
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
|
14
I USING THE OPTIONAL EASYCARE
EASYCARE (Fig. 30), available separately, is a cleaning aid
designed to maintain the standard performance of the eRapid
Aerosol Head. It is important not to use EASYCARE more than 2
times per week to maintain maximum eRapid Aerosol Head life.
1. Read the Instructions For Use for EASYCARE carefully and
completely before using it for the rst time.
2. Connect EASYCARE to the Controller as described in the
EASYCARE Instructions For Use.
3. To start the EASYCARE cleaning cycle press and hold down
the On/O button on the Controller for at least 10 seconds.
First you will hear one “beep” and the status light will
illuminate green. The START screen (Figure 17a) will appear
on the display.
4. After about 10 seconds you will hear a second “beep” and the
screen will change showing that the EASYCARE cleaning has
started (Figure 31). Release the On/O button.
NOTE: During EASYCARE cleaning make sure that either one of
the EASYCARE screens (Figure 31) are showing in the Controller
display. If the TREATMENT screens show (Figure 17b) shut
the Controller off and restart the EASYCARE cleaning cycle in
accordance with the above instructions.
5. When the EASYCARE cleaning cycle is completed you will hear
two “beeps”, and the same DOSE COMPLETE screen will appear
(Figure 18). The Controller will automatically shut o.
NOTE: In the event of a malfunction, see the Message Screens
and Warnings chart on Page 11, locate the alternating symbols,
and take the corrective action noted.
6. Rinse (see Section H) and Disinfect (see Section J) the
Aerosol Head after every EASYCARE cleaning cycle.
7. Refer to the EASYCARE Instructions For Use in disassembling
and maintaining the EASYCARE.
Figure
30
Figure
32
Figure
31
With Battery With AC Adapter
J EFLOW NEBULIZER HANDSET DISINFECTION
WARNING
To reduce the risk of serious or fatal illness caused by
contamination of the eRapid Nebulizer Handset you must
also DISINFECT THE HANDSET AT THE END OF EVERY
TREATMENT DAY. In addition, the eRapid Nebulizer Handset is
strictly FOR SINGLE PATIENT USE ONLY.
NOTE: The disinfection instructions described may be used in
both home and institutional environments.
1. Clean the eRapid Nebulizer Handset as described in Section H.
2. AT THE END OF EVERY TREATMENT DAY, disinfect the
eRapid Nebulizer Handset with a commercially available
medical device disinfectant such as Control III®. Follow the
disinfectant manufacturer’s directions for use.
3. The eRapid Nebulizer Handset may also be disinfected by
boiling the parts, including the Aerosol Head, in a clean pot of
DISTILLED water for a full 5 minutes. Do not boil in regular tap
water, as it may damage the Aerosol Head.
4. Air dry the eRapid Nebulizer Handset parts on a clean, lint-free
towel (Figure 32).
5. After the eRapid Nebulizer Handset parts are completely
dry, place them in a bag for storage. DO NOT re-assemble the
eRapid Nebulizer Handset until just prior to the next treatment.
This is to ensure that the silicone seals do not become
deformed over time.
6. Hospitals and clinics can sterilize the eRapid Nebulizer
Handset parts by wet autoclaving at 250° F (121° C) for 30
minutes. Follow the autoclave manufacturer’s instructions
for use.
Page 15
15
|
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
K FUNCTIONALITY TEST
A Functionality Test takes only a few minutes and is helpful if you
suspect the eRapid Nebulizer Handset is not working properly.
Follow the steps below and use only 2.5 mL (about 1/2 teaspoon)
sodium chloride 0.9% (normal saline) for the Functionality Test.
1. Assemble the eRapid Nebulizer Handset as described in
Section F, but do not attach the Mouthpiece.
2. Follow the procedure in Section G for taking a treatment.
However, for this Functionality Test only, use 2.5 mL (about
1/2 teaspoon) of sodium chloride 0.9% instead of medication.
3. Using a stop watch or clock with a second hand, time the
complete Functionality Test from when the eRapid Nebulizer
Handset starts producing aerosol until the Controller
automatically turns o.
4. After the Controller has automatically shut o, remove
the Medication Cap and check the amount of liquid in the
Medication Reservoir. Only about 1 mL (about 1/5 teaspoon)
of the solution should remain. If more than 1 mL remains,
clean the Aerosol Head and repeat the test. If, after proper
cleaning, there is still more than 1 mL remaining in the
Medication Reservoir, call 1-866-335-6943 for details.
5. If the time to nebulize the sodium chloride 0.9% is less than
5 minutes, the eRapid Nebulizer Handset is functioning
correctly. If it takes more than5 minutes to nebulize the
sodium chloride 0.9%, call 1-866-335-6943 for details. Clean
the eRapid Nebulizer Handset after this Functionality Test.
L FREQUENTLY ASKED QUESTIONS AND
TROUBLESHOOTING
QUESTION 1: How much medication should be left in the Medica-
tion Reservoir at the end of a treatment?
Answ er: Following treatment only about 1 mL (1/5 tea-
spoon) of medication should be remaining in the Medication
Reservoir. If less than 1 mL remains, check for leaks and
make sure the eFlow Nebulizer Handset is held level during
treatment. If more than 1 mL remains, put the Medication
Cap back on and restart the treatment. Following treatment,
clean the Aerosol Head (Section H). If, after proper cleaning,
more than 1 mL remains in the Medication Reservoir, call
1-866-335-6943.
QUESTION 2: How long should each treatment take?
Answ er: With normal operation and proper cleaning the
eRapid Nebulizer Handset should deliver 2.5 mL of sodium
chloride 0.9% is less than 5 minutes. If more than 5 minutes
is required to deliver 2.5 mL of sodium chloride 0.9%, call
1-866-335-6943.
QUESTION 3: When I turn on my eRapid Nebulizer System, nothing
happens. Why does there not seem to be any power?
Answ er: If you are using batteries, use the gures in each
battery compartment to verify that the batteries are inserted
correctly. If the batteries are positioned properly, check to see
if the alternating BATTERY LEVEL LOW icons are ashing on
the controller display. If they are, replace the batteries or use
the AC Power Supply.
Answ er: If you are using the AC Power Supply, check the
adapter connection to be sure it is rmly connected to the
adapter port located underneath the battery compartment.
Be sure that the adapter is plugged into a working wall outlet.
QUESTION 4: How long will a new set of batteries last?
Answ er: A new set of batteries will provide approximately 90
minutes of continuous treatment.
Answ er: Consider using rechargeable batteries.
QUESTION 5: What if no mist is coming out of the eRapid
Nebulizer Handset?
Answ er: First, check that the Controller has power. Secondly,
make sure the Nebulizer Connection Cord is correctly attached. Thirdly, check to be sure that the eRapid Nebulizer
Handset has been assembled properly (Section F). Lastly,
check to be sure medication is in the Medication Reservoir. If
the eRapid Nebulizer System still does not function properly,
call 1-866-335-6943.
QUESTION 6: What if liquid is leaking from the eRapid Nebulizer
Handset during the treatment?
Answ er: Check to see if the Inhalation Valve has been
deformed by storing the eRapid Nebulizer Handset
assembled.
Answ er: Be sure the Inhalation Valve is properly attached to
the Aerosol Chamber to prevent leaks (Section F, Figures 6a
and 6b).
Answ er: Ensure the Aerosol Head is inserted correctly
(Section F, Figures 7, 7a and 7b). Next, ensure the Medication
Reservoir and the Aerosol Chamber are closed correctly
(Section F, Figure 9).
QUESTION 7: What if my Controller shuts o before my treatment
begins, or does not restart?
Answ er: Press the On/O button for one full second. If it still
shuts o after several (3-4) attempts, call 1-866-335-6943.
QUESTION 8: What if my Controller does not shut o at the end of
my treatment?
Answ er: Press the On/O button again.
Answ er: Disconnect the AC Power Supply from the Controller
and remove the batteries.
Please note that the Controller has a built-in, automatic
shuto after 20 minutes of operation. Before it shuts o
the Controller will display the CAUTION screen, not the DOSE
COMPLETE screen (see Message Screens and Warnings).
This is not a malfunction. However, if this situation continues
three or four times, call 1-866-335-6943.
QUESTION 9: When I started my EASYCARE the EASYCARE screen
did not appear on the display and the TREATMENT screen
appeared instead. What do I do?
Answ er: Press and hold the Controller’s On/O Button for
three full seconds. A 5-beep alarm tone will sound, the
status light on the Controller will ash RED-GREEN, and
the TREATMENT INTERRUPTED screen will appear. After 10
seconds the Controller will automatically shut o. Restart
the EASYCARE cycle as described in Section I. When the
EASYCARE screen appears you are in the EASYCARE mode.
If this situation occurs several (3-4) times call
1-866-335-6943.
Page 16
QUESTIONS ABOUT ERAPID? CALL 1-866-335-6943
|
16
M SPECIFICATIONS
Weight: Controller and eRapid Nebulizer Handset ...................... 6 oz
Weight: Controller, eRapid Nebulizer Handset, and Batteries 9.5 oz
Dimensions of eRapid Nebulizer Handset ....... 1.97” X 2.26” X 5.18”
Electrical Requirements ...........................110 V - 240 V, 50 Hz/60 Hz
Power Wattage .......................................2.0 Watts under normal load
Min. Fill Volume ........................................................................... 2.0 mL
Max. Fill Volume .......................................................................... 6.0 mL
TRANSPORT / STORAGE
Ambient Temperature .......................................................-4° to 140° F
Ambient Humidity ...............................................................10% to 95%
RECHARGEABLE BATTERIES
Rechargeable Batteries .............................. 1.2V-1.5V, min 1500mAh
Rechargeable Battery Operation ....................... About 90 minutes of
.............................................................................continuous treatment
Rechargeable Battery Charge Time ............................ up to 15 hours,
.................................................................................... (depends on type
..................................................................................of battery charger)
DISPOSABLE BATTERIES
Panasonic Evoia or equivalent ..................................................... 1.5V
Panasonic Power Digital or equivalent ........................................1.5V
MANUFACTURED IN GERMANY & DISTRIBUTED BY:
PARI Respiratory Equipment, Inc.
2412 PARI Way
Midlothian, VA 23112
Tel: Toll Free (U.S.A. only) 1-800-FAST-NEB (327-8632)
Canada and International 1-804-253-PARI (7274)
www.pari.com
PATENT NOS:
US 6,962,151; US 6,983,747; US 7,252,085; US 7,931,212; US
7,458,372 and; US 7,316,067. Additional patents pending.
DESIGN AWARDS:
©
2012 PARI Pharma GmbH. All rights reserved. Altera, eFlow and TRIO are registered trademarks of PARI
Pharma GmbH. eRapid is a trademark of PARI Pharma GmbH. Touchspray Technology® is under license
from the Technology Partnership plc. Control III is a registered trademark of Maril Products, Inc.
178D1009 Rev B 10/12
®
Loading...