Parex Electronics and Computer BT1810 User Manual

Optoma remote control operating manual

Pairing your BT remote control with the projector

Press the [HOME] and [Return] buttons simultaneously for 2 seconds. The status LED on the BT remote
control will flash, indicating the device is in pairing mode.

The pairing process will take approximately 20 seconds. If the pairing is successful, the status LED on the
BT remote control will turn solid blue. Otherwise, the status LED on the BT remote control will turn solid
red. If the BT remote control is left idle for 10 minutes, it will automatically enter Sleep mode and the
Bluetooth is disconnected.

Note:

. The actual remote control may vary depending on the region.
. Some keys may have no function for models that do not support these features.

Effective range

Infra-Red (IR) remote control sensor is located on the rear of the projector. Ensure to hold the remote
control at an

angle within 30° (horizontally) or 20° (vertically) perpendicular to the projector’s IR remote control sensor

to function
correctly. The distance between the remote control and the sensor should not be longer than 7 meters
(~22 feet).
You can also operate the remote control by pointing it to the projected image.

Note: When pointing the remote control directly (0 degrees angle) on the IR sensor, the distance between

the remote control and the sensor should not be longer than 10 meters (~32 feet).

. Make sure that there are no obstacles between the remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
. Make sure the IR transmitter of the remote control is not being shined by sunlight or fluorescent lamps
directly.
. Please keep the remote controller away from fluorescent lamps for over 2 meters or the remote
controller might become malfunction.
. If the remote control is close to Inverter-Type fluorescent lamps, it might become ineffective from time
to time.
. If the remote control and the projector are within a very short distance, the remote control might
become ineffective.
. When you aim at the screen, the effective distance is less than 7 meters from the remote control to the
screen and reflecting the IR beams back to the projector. However, the effective range might change
according to screens.

Optoma global offices

For service or support, please contact your local office.

USA

47697 Westinghouse Drive, 888-289-6786
Fremont, CA 94539, USA 510-897-8601
www.optomausa.com [email protected]

Canada

47697 Westinghouse Drive, 888-289-6786
Fremont, CA 94539, USA 510-897-8601
www.optomausa.com [email protected]

Latin America

47697 Westinghouse Drive, 888-289-6786
Fremont, CA 94539, USA 510-897-8601
www.optomausa.com [email protected]

Europe

Unit 1, Network 41, Bourne End Mills,
Hemel Hempstead, Herts,
HP1 2UJ, United Kingdom [phone]
www.optoma.eu [phone]
Service Tel : [phone] [email protected]

Benelux BV

Randstad 22-123 [phone]
1316 BW Almere [phone]

The Netherlands
www.optoma.nl

France

Batiment E [phone]
81-83 avenue Edouard Vaillant [phone]
92100 Boulogne Billancourt, France [email protected]

Spain

C/ José Hierro,36 Of. 1C [phone]
28522 Rivas VaciaMadrid, [phone]
Spain

Deutschland

Wiesenstrasse 21 W [phone]
D40549 Düsseldorf, [phone]
Germany [email protected]

Scandinavia

Lerpeveien 25 [phone]
3040 Drammen [phone]
Norway [email protected]
PO.BOX 9515
3038 Drammen
Norway

Korea

WOOMI TECH.CO.,LTD. +82+2+34430004
4F, Minu Bldg.33-14, Kangnam-Ku, +82+2+34430005
Seoul,135-815, KOREA
korea.optoma.com

Japan

東京都足立区綾瀬3-25-18
株式会社オーエス[email protected]
コンタクトセンター:0120-380-495 www.os-worldwide.com

Taiwan

12F., No.213, Sec. 3, Beixin Rd., [phone]
Xindian Dist., New Taipei City 231, [phone]
Taiwan, R.O.C. [email protected]
www.optoma.com.tw asia.optoma.com

Hong Kong

Unit A, 27/F Dragon Centre,
79 Wing Hong Street, [phone]
Cheung Sha Wan, [phone]
Kowloon, Hong Kong www.optoma.com.hk

China

5F, No. 1205, Kaixuan Rd., [phone]
Changning District [phone]
Shanghai, 200052, China www.optoma.com.cn

Federal Communications Commission (FCC) Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generate, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.

RF exposure warning

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This product may not be collocated or operated in conjunction with any other antenna or
transmitter