Parex Electronics and Computer BT1311 User Manual

F1 F2

F3

Port

Up Dn

CAPS

Num Pow

er Sync

Welcome:

™

Model: BT1311

Operation Manual

I. Quick Start

thumb controlled optical mouse in the spacebar and finger tip activation buttons. You are invited
to read Operation Manual to get the most from this new computer component. This Operation
Manual is available at: www.falconBTkeyboard.com

On/Off

Thanks for purchasing a falcon

Activation Keys

, a full-size Bluetooth multi-platform keyboard with

USB Charging

Sync Switch

R14

LEDS:

Left Click

Right Click

LEDS:

Cursor Port

What is in the Box?:

• Bluetooth keyboard with 'falcon™' mouse

• USB charging cable

• Quick Start instructions

Getting Started

• Perform charging from a PC or authorized power source not exceeding 5.0 DCV, using the

USB charging cable provided with your keyboard until red charging light turns green.

1

• Syncing: The falcon™ is a multi-platform keyboard, capable of being operated with any

computer, iPAD, iPhone, or Tablet device equipped with Bluetooth chip set or Bluetooth
dongle. The synced device must support the "Bluetooth HID profile. Microsoft 7 (or later),
Android 4, and iOS 4.0 should work whereas the Blackberry will not. The Blackberry will
require a third party "patch".

Synching the with your falcon™ keyboard.

• Turn on your falcon™ using the upper left hand On/Off button.

• Turn on the device to be paired.

• Click Fn + F1 together to connect the first bluetooth unit

• Press the "synch" button on the upper right hand corner of the

keyboard.

• The "synch" LED should start flashing blue.

• Go to the Bluetooth Control Panel on the device being paired

• Make sure Bluetooth is "on" and searching for devices

• When Falcon is found, instruct it to “PAIR”

• A number will show up with instructions to enter the code on

"falcon Keyboard", followed by the return or enter key.

• Be sure to press "Enter" to complete syncing. Once paired, it should

remain paired on subsequent uses.

• If difficulty is encountered in synching, instructions for different types

of units are provided in Appendix B of the Operation Manual.

• Set the cursor tracking speed to SLOW on the unit's control panel.

• Increase speed as you gain experience. (See below for cursor precision

which is different from cursor speed)

• Repeat pressing Fn + F2 together, then sync to a second unit, and Fn + F3

together, then sync for a third unit.

Helpful Hints:

• The use of a mouse, thumb pad, or track ball is habit forming. To get the most from the

falcon™, hide your mouse where it cannot be reached and disable the track ball or thumb
pad. You will have to form a new habit in the use of your thumb or finger tip to become

proficient with the falcon™ to avoid reaching for the mouse or thumb pad.

• A right handed beginner may find that it is easier to have the left hand operate the select and

pull down activation keys rather than doing it with the right hand as the thumb is
maneuvering the cursor. Press Fn+L+R at the same time to switch back and forth for left or
right hand operation.

• Either the down-side of the right or left thumb or a finger tip moving horizontally over the

space bar lens can be used to move the cursor.

• The 105 keys with 1.9 cm (0.75 in) provide the feeling of a full keyboard.

• Ability to toggle back and forth for typing on either your PC, tablet or smart-phone.

• LED displays with different colors show status of key features.

• The LEDs, located above F1, F2, F3 flash blue when paired successfully with a Bluetooth

component. By pressing Fn+F1 together, then pressing Sync, you connect with your first

2

unit. Fn + F2 together, then sync your second unit. Fn +F3 together, then sync for the third
unit.

• Precise location of the cursor on the monitor can be assisted by varying the DPI (dots per

inch-the accuracy of the picture being taken) Changing from 400, 600, 800 or 1200 DPI is
performed by pressing Fn + S together. Repeating FN + S steps through each DPI in order.
A very slight movement of the thumb or finger on the lens can show the change in
movement speed from one DPI step to the next.

• If the keyboard turns off during periods of non-use, it can be restated by pressing any key.

• If the 3 devices have all paired successfully , you can press FN+F1, or FN+F2, or FN+F3 to

switch from one device to another.

• If the keyboard is turned off, it should remain synced when it is turned on again.

3