Paramount Fitness VERONA, VERONA BLT-999T-3 Instruction Manual
READ & SAVE THESE INSTRUCTIONS
Carefully read and review before assembling, installing,
operating or maintaining this product. Observe all safety
instructions and information.
FAILURE TO FOLLOW WARNINGS & OPERATIONAL
INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT
IN PROPERTY DAMAGE OR PERSONAL INJURY.
VERONA
ELECTRIC STOVE
INSTRUCTIONS FOR USE
Item number: ES-330
Model number: BLT-999T-3
Important: Read all instructions and warnings carefully before starting installation.
Failure to follow these instructions may result in a possible electric shock, re hazard and
will void the warranty .
Read all instructions before using this appliance.
This replace is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. If provided, use handles when moving this appliance. Keep combustible
materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3
feet from the front and sides of this appliance.
Caution: Extreme caution is necessary when any heater is used near children or
disabled persons. Never leave any heater unattended.
Always unplug this appliance when not in use.
Do not operate any heater with a damaged cord or plug or after the appliance
malfunctions, or has been dropped or damaged in any manner.
Any repairs to this appliance must be carried out by a qualied service person
Under no circumstances should this appliance be modied. Parts having to be
removed for servicing must be replaced prior to operating this appliance again.
Do not use outdoors.
This appliance is not intended for use in bathrooms, laundry areas and similar indoor
locations. Never locate this appliance where it may fall into a bathtub or otherwise
become exposed to water.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like.
Arrange cord away from trac areas and where it will not be tripped over.
To disconnect this appliance, turn controls to the o position, then remove the plug
from the outlet.
Connect to properly grounded outlets only.
This appliance, when installed must be electrically grounded in accordance with local
codes, and the National Electrical Code, ANSI/NFPA No. 70.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this
may cause an electric shock, re or damage the appliance.
To prevent possible re, do not block air intakes or exhaust in any manner. Do not use
on soft surfaces, like a bed, where openings may become blocked.
This appliance has hot and arching or sparking parts inside. Do not use it in areas
where gasoline, paint or ammable liquids are used or stored. This appliance should
not be used as a drying rack for clothing, nor should Christmas stockings or
decorations be hung on or near it.
INSTALLATION INSTRUCTIONS – GENERAL
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
-1-
A 15 Amp, 110 Volt, 60 Hz circuit withaproperly grounded outlet is required to operate this
appliance. The fireplace must be on a dedicated circuit as other appliances on the same
circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard witha6.5 ft long 3 wire cord, exiting out the back of the
fireplace. Plan the installation to avoid the use of an extension cord.
ELECTRICAL CONNECTION
SPECIFICATIONS
Dimensions LxWxH
Net Weight
Voltage
Frequency
Watts
Heater Rating
21.73"x6.02"x19.49"
19.8 lbs
110-120V~
60 Hz
1400 W
4776 BTU
WARNING:
Electrical outlet wiring must comply with local building codes and other
applicable regulations to reduce the risk of re, electrical shock and injury to persons.
WARNING: Do not use this replace if any part of it has become wet. Immediately call a
qualied service technician to inspect the replace and replace any part of the electrical
system which has been wet.
17.
Use this appliance only as described in this manual. Any other use not recommended
18.
Avoid the use of an extension cord because the extension cord may overheat and
cause a re.
by the manufacturer may cause re, electric shock or injury to persons.
-2-
.
-3-
Always plug heaters directly into a wall outlet/receptacle. Never use
with an extension cord or relocatable power tap (outlet/power strip)
The cord has a plug as shown in (A) of Figure 1 given below.
T
Figure 1
(A)
(B)
Grounding Methods
METAL SCREW
COVER OF GROUNDED
OUTLET BOX
GROUNDING PIN
ADAPTER
GROUNDING
MEANS
NOT ALLOWED
IN CANADA
CONTROLS/OPERATION
Your fireplace has the following functions:
FOR YOUR SAFETY
Repairs must be performed by a qualified person.
REPLACING THE LIGHT BULBS
This fireplace uses 2 clear 110 Volt, 40 Watt, E-12 socket base light bulbs (small base,
chandelier candle type bulb). The access plate is located on the back of the unit. For
convenience, if one of the light bulbs burns out, it may be easier to replace both of the
light bulbs at the same time.
WARNING: Do not exceed 40 Watts per bulb. Use of higher a rated bulb may result in a
fire, causing property damage, personal injury or loss of life.
1. Turn off the power to the unit, and unplug it from the electrical outlet.
2. Let the fireplace cool if it has been operating.
3. Turn the fireplace so you are facing the back of the fireplace.
4. Look for the access plate with the gold printing on it.
5. Remove the 2 screws holding the access plate in position (FIG1). Once you have
removed the 2 screws, lift the access plate so the 2 positioning tabs come free of
their slots. Once you have removed the access plate you can see and access the
40 watt chandelier bulb (FIG 2).
FIG 1
FIG 2
Low heat II
700 watts
On/Off I / O
Power to the unit
High heat III
1400 watts
Note: For a high level of
heat press “II” and “III”
-4-
BULB COVER
Temperature Adjustment
Dimming Adjustment
The control switches are on the back of the unit.
1. Plug the appliance into the socket and press “ I ” to turn on
2. Adjust the dimming knob for the desired flame effect.
3. For a low level of heat press “ II ”
4. For a high level of heat press “II” and “III”
Adjust the thermostat control knob to regulate the heat.
Dimming
Intensité
Loading...