Paramount Fitness SwingJet Installation Manual

1. NEW SWING JET

• The swing jet comes packed with the cover

off.

• Push the nozzle up and look and feel for

the raised area on the side of the colored

nozzle that is in the center of the cream
colored Cam. (Fig 1). The nozzle jet open-

ing is 180 degrees opposite that raised

area. Push the nozzle shaft up and down

until the nozzle jet is either all the way right

or all the way left so when you are doing

the next two steps you are aware of which

direction it is going to travel when rotating.

• There are three notches in the cream col-

ored cam above the raised area (Fig 1).

These cam notches are in a straight line

with the cam notches on the opposite side

of the raised area. The jet opening of the

nozzle goes back and forth covering the

90 degree arc formed by the three ratchet

positions as the nozzle extends and retracts

when cycled.

• Put one wrap minimum of Teflon tape on

the threads to make the nozzle threads not

seize up over time, and thread the swing

jet in the return fitting tight, using the swing

jet installation and removal tool. It should

be tight enough so it can not be turned by

hand. Hand tighten only, NEVER USE A

WRENCH DIRECTLY ON THE SWING JET.

ALWAYS REMOVE THE COVER AND USE
THE TOOL (Fig 2 & 3) (AVAILABLE FROM

PARAMOUNT 005-721-4541-00) TO COV-

ER THE SWING JET RETAINER BEFORE

USING A WRENCH TO REMOVE THE

SWINGJET.

www.1Paramount.com 1.800.621.5886

INSTALLATION GUIDE:
SWINGJET

FIG. 1

NOTCHES

RAISED AREA

NOZZLE

SWINGJET TOOL

FIG. 2

TO REMOVE

RETAINER

FIG. 3

• Grasp the cream colored cam and turn it
either way to aim the nozzle jet to clean the
desired area. Remember the nozzle is going
to ratchet right or left depending on which of
the two side notches you placed the pins in.

(Fig 1)

• Once in position find the clip on the outside
ring of the nozzle retainer (Fig 4) and place
the hole in the cover so it is just to the coun­ter clock wise side of the retainer clip (Fig 4).
Line up the notches on the cover with the
locking cams on the nozzle retainer. Push
the cover on to the retainer and rotate clock­wise until the clip snaps in the hole (Fig 4).
Do not force the cover on when not in posi­tion. It will be difficult to remove.

2. ADJUSTING A SWINGJET WHEN IT IS

THREADED IN PLACE

• Turn the pump on so the Swing Jet is on. If
the Swing Jet is on a water valve circuit, wait
for the Swing Jet to come on, and pause the
water valve.

• Place the swing jet tool (Fig 2) provided with
the unit (part # 005-721-4541-00) over the
cover with the spring loaded key over the
hole on the side of the cover of the swing jet
(Fig 5 &6). Leaving the key in place, while
pushing down on the button key rotate the
cover counter clockwise until it stops. Do not
remove the key. The extended nozzle should
now be able to be rotated to the desired posi­tion. If the nozzle won’t easily rotate remove
the key and very slightly move the cover
counter clock wise until the nozzle will rotate.
Once the nozzle is set to the correct position,
remove the key and rotate the cover clock
wise to re-lock the cover in place.

· Cycle the Swing Jet by turning the pump off
and on to make sure you have set it in the
desired position.

INSTALLATION GUIDE:
SWINGJET (CONTINUED)

www.1Paramount.com 1.800.621.5886

U.S. Patents 7,578,010 7,481,377 6,899,285 004-027-8805-00 REV121310

FIG. 6

TO REMOVE

COVER

FIG. 5

KEY HOLE

FIG. 4

KEY HOLE

CLIP ON NOZZLE

RETAINER