Paramount Fitness PH05-S, PH05-SS Assembly Manual

TABLE TOP FLAME HEATER

Item Number: PH-T-113
Model Number: PH05-S/PH05-SS

ASSEMBLY AND OPERATION INSTRUCTIONS

WARNING

Read this instruction before using this
appliance. The appliance must be installed
in accordanc e with the instructions and
local regulations. The use of this appliance
in enclosed areas can be dangerous and is
PROHIBITED

IF YOU SMELL GAS

• Close the valve of the gas cylinder or
regulator.

• Extinguish all naked flames; do not operate
any electrical appliances.

• Check for leaks as detailed in this instructions.

• If odor persists, contact your dealer or gas

supplier immediately.

• Do the leak test after each changing LPG
cylinder.

• Never check for leaks with a match or open

• Do not store or use gas oline or other

this appliance.

FOR OUTDFOOR USE ONLY | USES PROPANE LPG ONLY

PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY

RETAIN THIS MANUAL FOR REFERENCE

For cus tomer service, parts

or warranty issues:

Call 1-800-561-5550

or e-mail [e-mail]

CARBON MONOXIDE HAZARD

• This appliance can produce carbon monoxide which
has no odor.

• Using it in an enclosed space can kill you.

• Never use this appliance in a enclosed space such
as a camper, tent, car or home.

• Keep electrical supply cord away from the heated

surfaces.

WARNING:

• Improper installation, adjustment, alteration,
services or maintenance can cause injury, death or
property damage.

• Read the installation, operating and maintenance
instructions thoroughly before installing or servicing
this equipment.

WARNING:

FOR OUTDOOR USE ONLY.

• Cylinders to be used must be constructed
And marked in accordance with US DOT
specifications.

• Storage indoors is permissible only if the
cylinder is removed.

• The unit should be secured or moved

Indoors if winds exceed 19.5mph.

Note:
Use for 1lb.LPG tank, but it is not supplied.
Use for CSA regulator with 0.6m gas hose.
This regulator is set for an outlet pressure
of 11 inches water column.

TOOLS NEEDED

Philips head screwdriver

Leak detection solution

For questions, replacement
parts, service contact:
[e-mail]

DANGER

- 2 -

PRECAUTIONS

• Installation and services should only be a qualied person.

• Do not use the heater in an explosive atmosphere.

• Before to use, check the hose.

• Disconnect LPG cylinder before moving the heater.

• Do not attempt to alter any parts of the heater.
Example: Using the heater without reector or protection guard.

• The appliance shall not be used in basements or below ground level.

• It must always be placed on a solid and level surface.

• Never replace or substitute the regulator use only that one is suitable both appliance
category and normal pressure of gas.

• Do not clean the heater with cleaners that are combustible or corrosive.

• Do not paint protection guard, control box or reector.

• The LPG gas cylinder valve should be turned off and disconnect the cylinder with the heater

when the heater is not in use.

• Don't not use the heater when it is raining, and do not let any liquid splash to the glass tube
when the heater is working.

• Keep the children away from the heater, always be carefully not to knock down the heater,
which will break the glass tube and might cause injury.

• Do not move the appliance when in operation.

• After a long break of operation, the gas parts in the control box of the heater and the hose
should be inspected for spiders, spider webs or other insects.

Check the heater immediately if any of the following exists:

1. There is smell of gas.

2. The heater is not enough effective.

3. The burner makes popping noise during use (a slight popping noise is normal when the
burner is extinguished after use).

• If you smell gas, turn off the valve immediately. If smell persists, contact the dealer or gas
supplier immediately.

• The hose with regulator assembly shall be stored on a safety place to avoid it’s accidental

damage.

• Children and adults should be aware of the high surface temperature hazard, and should
keep a safe distance away to avoid clothes burning or igniting.

- 3 -

• Young children should be carefully supervised when they are in the working area of the

heater.

• Clothing or other ammable material should not be hung from the heater, or placed on or

near the heater.

• Do not obstruct the ow of combustion products.

• Keep the ventilation opening of the cylinder enclosure free and clear of debris.

• Do not obstruct the ventilation holes of the cylinder housing.

• Shut off the valve of gas cylinder or the regulator before moving the appliance.

• The tubing or the exible hose must be changed within the prescribed intervals.

• Use only the type of gas and the type of cylinder specied by the manufacturer.

• In case of violent wind particular attention must be taken against tilting of the appliance.

• Storage of the heater indoor is permitted only if the cylinder is disconnected and removed

from the appliance.

• Do not store a spare LP-gas cylinder under or near this heater.

• Never ll the cylinder beyond 80 percent full.

- 4 -

DIAGRAMMATICAL REPRESENTATIONS

OF OUTDOOR AREAS

APPLIANCE STAND AND LOACTION

- The appliance is for outdoor use only. Do not

use it for indoor or in an enclosed area.

- Alw a ys m ainta i n pr o per c lear a nce f rom
combustible materials, i.e. top 800mm and sides
650mm minimum.

- 5 -

LEAKAGE TEST

Gas connections on the appliance are leak tested at the factory prior to shipment. Possible
mishandling of the appliance during the shipment might contribute to product integrity as a
whole. A complete gas leakage test must be performed again at the installation site. Please
follow the procedure below for leakage test.

- Make a soap solution of one part liquid detergent and one part water. The soap solution can
be applied with spray bottle, brush or rag. Soap bubbles will appear where a leak is present.

- Make sure the control tap is in the “OFF” position (full disk = ●) on the control panel.

- Turn on the gas supply and check for bubbles from the hoses and connections. Presents of
bubble means that a leak path is present.

- If a leak is present, turn OFF the gas supply immediately, tighten any leaking tting carefully,
turn gas again and recheck.

- Never leak test while smoking.

INSTALLATION

Important safety requirements:

THIS APPLIANCE OUTDOOR USE ONLY

1. This appliance shall not be installed or used indoors, in buildings, garages or any other

enclosed area.

2. DO NOT place articles on or against this appliance.

3. DO NOT use or store ammable materials near this appliance.

4. DO NOT operate this appliance unless it is fully assembled with reector and protection
guard in place.

5. Installation and repair should be done by a qualied service person. The appliance must
be inspected before use and at least annually by a qualied service person. More frequent
cleaning may be required as necessary. It is imperative that control compartment, burners
and circulating air passages of the heater and light be kept clean.

6. Please use the pressure regulator and hose assembly supplied with the heater, the
replacement pressure regulator and hose assemblies must be according to ANSI/UL 144.

- 6 -

PARTS LIST-1

Part NO. Part Name QTY Remarks

Bottom Plate

Control Box

Middle Plate

Support

Upper Plate

Plate cover

Glass tube

Damper

Reector

1

1

1

4

1

1

1

1

1

1

2

3

5

6

7

8

9

10

Preassembled in

the Middle plate

Preassembled in

the Middle plate

Preassembled in

upper plate

Picture

- 7 -

PARTS LIST-2

Part NO. Part Name QTY Remarks

Two side bolts

Hook

Mesh Guard

Guard Fastening

Side panel

Front panel

Screw M4

Knob

Nuts

AA battery

3

8

4

4

3

1

66

1

1

1

11

12

13

14

15

16

17

18

19

20

Connect with

damper and

reector

A chain is

preassembled in

this panel

All preassembled

in relative parts

Preassembled in

the front panel

Optional part

Picture

Pieces

- 8 -

HEATER ASSEMBLY

Tools Required:
1 Phillips head screwdriver, 1 adjustable spanner

1. Remove the protective paperboard off the

top of glass tube
Assemble the reflector into the frame parts

using two-side bolts, then use the nuts to
rm the top.

2. Us ing wing nu ts to firm the reflect or

completely.

- 9 -

INJECTOR

3. Inner regulator is stored inside. Pl connect
the regulator with 1 pound gas cylinder
tightly.(Cylinder is not provided)

4. Assembling is completed. Start to operate

by reading the following operation manual

OPERATION

Preparation:

You will need to purchase a 1 pound propane cylinder before
you start to use.
Connect the cylinder with the inner regulator

Warning:

Always test the connection place leaks with soapy water.
Any guard or protective device removed for servicing the heater

must be replaced prior to operation.

Warning:

Never use the heater while it is raining, the glass tube would break when it
suddenly met water.
Always turn off the heater while there is a rain.
Never splash any liquid to the glass tube when the heater is working
The glass tube will be extremely hot when it is working, never try to touch it and
Keep the children away from the heater.
Always ensure the heater stands rmly, the glass tube may break if the heater was

fell down onto ground.

Never use the heater if the glass tube has any crack

●

●

●

●

●

●

LIGHTING INSTRUCTIONS

Check and ensure that an AA battery is inside the ignition

chamber and has power. Ensure

The anode (+) faces outside.

Ensure that the control knob is OFF. Slowly open the
gas cylinder valve.
Press and turn the control knob to LIGHT position,
push the igniter to generate spark while keeping control
knob in pressed position
Check for pilot ame through glass tube. If pilot does
not light, turn control knob to ‘OFF’ position wait two
minutes minimum and try again from the start. Some
attempts may be necessary.
If the pilot alight, keep control knob pressed for 15
seconds then turn the control knob to ‘LOW’.
For maximum heat turn control knob to ‘HIGH’.
To turn heater off, turn control knob to ‘OFF’.
Close the vlave of the gas cylinder or the regulator after

use.

1.

2.

3.

4.

5.

6.

7.

OFF

LIGHT

LOW

HIGH

OFF

LO

HI

WARNING

FOR YOUR SAFETY:

● DO NOT touch or move heater for at
Least 45 minutes after use.

● Allow all burner elements to cool

before touching.

NOTE

● In a salt-air environment (such as near an
Ocean) corrosion occurs more quickly than

normal.

● Frequently check for corroded areas and
Repair them promptly.

● Wait until heater is cool before covering.

- 10 -

CLEANING AND MAINTENANCE:

Storage between usage:

During periods of extended inactivity or when transporting:

CLEANING/MAINTENANCE/STORAGE

●

●

●

●

●

●

●

●

●

●

●

●

●

●

- 11 -

To enjoy outstanding performance of your heater for years make sure to perform the
following maintenance activities on a regular basis:
Keep exterior surfaces clean.

-Use warm soapy water for cleaning. Never use flammable, corrosive or abrasive

cleaners.

-While washing your unit, be sure to keep the area around the burner and pilot assembly
dry at all time. If the gas control is exposed to water in any way, do NOT try to use it. It

must be replaced.

After a long break from operation, the unit should be inspected for spiders, spider webs

or other insects.

Air ow must be unobstructed. Keep controls. Burner and circulating air passageways

clean.

Signs of possible blockage include:

-Gas odor with extreme yellow tipping of ame.

-Heater does NOT reach the desired temperature.

-Heater glow is excessively uneven.

-Heater makes popping noises.
Spider and insects can nest in burner or orices.

This dangerous condition can damage heater and render it unsafe for use. Clean burner

holes by using a heavy-duty pipe cleaner.
Compressed air may help clear away smaller particles.
Carbon deposits may create a re hazard. Clean reector and glass tube inside abo with
soapy water if any carbon deposits develop. Always be careful when cleaning the glass

tube.

Turn the control knob to “OFF” position.
Take cylinder out of product.
Store heater upright in an area sheltered away from weather conditions (such as rain,
sleet, hail, snow).
if desired, cover heater to protect exterior surfaces and to help prevent dust and debris

collecting in air passages.

Turn the control knob to “OFF” position.
Disconnect LP Cylinder and move to a secure, well-ventilated location outdoors.
DO NOT store in a location that will exceed 50 degrees C.
Store heater upright in an area sheltered away from weather conditions (such as rain,
sleet, hail, snow).
If desired, cover heater to protect exterior surfaces and to help prevent dust and debris

collecting in air passages.

Troubleshooting

PROBLEM PROBABLE CAUSE SOLUTION

Gas valve may be OFF

Fuel Tank empty

Orice blocked

Air in supply system

Loose connection

Debris around pilot

Loose connection

Thermocouple bad

Gas leak in line

Lack of fuel pressure

Pressure is low

Orice blocked

Control Valve not ON

Thermocouple bad

Pilot light assembly bent Or

not in correct location .

Turn the gas valve ON

Rell LP gas tank

Clean or replace Orice

Purge air from lines

Check all ttings

Clean dirty area

Tighten connection .

Replace Thermocouple

Check connections

Fuel tank is near empty

Fuel tank is near empty

Remove, clean and replace

Turn valve to ON .

Replace Thermocouple

Pilot will not light

Pilot will not stay on

Burner will not light

• Any repairs to the patio heater must be carried out by a qualied person.

• For questions, replacement parts, service, PLEASE CONTACT AZ PATIO HEATER

FOR 100% COMPLETE AFTER SERVICE LIVE SUPPORT 1-888-775-1330. CALL'S

ANSWERED 7 DAYS A WEEK BETWEEN 6:30 AM TO 4:30 PM PACIFIC STANDARD

TIME.

- 12 -

IMPOR TANT

.

For questions, concerns or problems with our product please

email our customer service department:

[e-mail] or call 1-800-561-5550.

DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE.

WARRANTY

This product is inspected, tested and carefully packaged to minimize the chance of
damage during shipment. If a part (excluding light bulbs and fuses*) within one year from
the date of purchase proves to be defective in material or fabrication under normal
use, the part will be repaired or replaced. The Company’s obligation under the warranty
is to replace or repair defective parts at our discretion. Any expenses or damage resulting
from the installation, removal or transportation of the product will be the responsibility
of the owner and are not covered by this warranty. The owner assumes all other risks
arising from the use or misuse of the product. The warranty will be void if the product
damage or failure is deemed by the Company to be caused by accident,
alteration, misuse, abuse, incorrect installation or removal, or connection to an incorrect
power source by the owner. The Company neither assumes, nor authorizes any person or
entity to assume for it any obligation or liability associated with its products.
Light bulbs and fuses are not covered under this warranty. If you have any questions
regarding the warranty or service, please call our toll free number: 1-800-561-5550.

Customer Service
JR Home Products
Unit 1 - 5628 Riverbend Drive, Burnaby BC, V3N 0C1
Toll Free: 1-800-561-5550
E-mail: [e-mail]

You MUST register your product to receive warranty service.

Registration can be completed online at www.jrhome.com or by mailing this form.

Warranty Registration Information Form / Formulaire d’enregistrement de la garantie

Name / Nom:
Street / Adress:
City / Ville:
Province / Province:
Postal Code / Code postal:

Daytime Phone # / No téléphone jour:
Evening Phone # / No téléphone soir:

E-Mail Address / Courriel:

Product/Produit:
Place of Purchase / Lieu de l’achat:
Date of Purchase / Date de l’achat:
Model # / No de modèle:
Serial # / Numéro de série:

You MUST register your product to receive
warranty service.

For warranty service, cont act J&R Home
Products at the address, phone numbers listed
below within 30 days of pur chase. Be sure to
have your sales receipt and original date of
purchase. All warranty service will be
coordinated by
J&R Home Products service center.

Vous DEVEZ enregistrer votre produit pour vous
prévaloir de la garantie.

Afin de faire valoir la garantie, communiquez
avec J&R Home Products à l’adresse et aux
numéros indiqués ci-dessous dans les 30 jours
suivant la date d’achat. Ayez en main votre reçu
et la date d’achat. Toutes les demandes liées
aux gar anties seront traitées par le centre de
service de J&R Home Products.

Please mail to / Veuillez poster le tout à : Parts & Service Department, J&R Home Pr oducts Ltd. Unit 1 - 5628 Riverbend Drive, Burnaby BC, V3N 0C1 1.800.561.5550