Paragon Outdoor PR100N1, PR11WD2W, PR11WTW Assembly Guide
11’6”
350
cm
10’6”
320
cm
11’x11’ Pergola
Assembly Instructions
11’6”
cm
350
F
B
A
3
R
I
C
7’9”
235cm
Paragon Group USA
Customer Service:(877) 782 4482 Email:cs-outdoors@paragongroupusa.com
Introduction
Thank you for purchasing the 11’x11’ Pergola.
When properly assembled and maintained, this pergola will provide many years of enjoyment!
These instructions include helpful hints and important information needed to safely assemble and properly main tain the pergola. Please read these instructions completely before you begin.
Our patented pergola has been designed for easy assembly. All steps can be completed by a team of
three people. The assembly should take about two hours.
Before Starting Assembly:
CAREFULLY READ ALL THE INSTRUCTIONS BEFORE YOU BEGIN AND FOLLOW THE
STEPS IN THE ORDER THEY ARE PRESENTED.
1. Make sure you have all the necessary parts:
Compare the contents of the three cartons to the List of Parts. If any parts are missing or damaged, or
you have any questions, please contact Customer service:
2. Lay the parts out in separate staging areas:
The List of Parts has the corresponding step number referenced to each part. We recommend that
while you go through the list, make staging areas for each step and place the parts necessary for
each step in these areas. This will save you time and during assembly.
(877) 782 4482 before beginning assembly.
3. Select a Location:
When selecting a location for your pergola, a level area is essential and if possible with proper
water drainage and easy access to power and water, if neccessary.
Choose a sunny, level position away from overhanging trees and power lines and protected from the
wind as much as possible. Locate underground pipes or cables before preparing the site or anchoring
the pergola.
Note: You may assemble the pergola on a hard level surface and move it to its location when
Make sure that there are no obstacles between the assembly area and the position.
4. Prepare a Foundation:
After choosing a location, proper preparation of the site is recommended. The site must be level.
If the site is not level, create a base slightly larger than the outside dimensions of the pergola using a
perimeter of two by fours with either soil, sod or gravel.
Make sure the base is square by measuring the diagonals from both directions and making sure
they are equal. The pergola is secured with pegs into holes cast with concrete.
If
you decide to have a concrete base, it is best to contact a reliable contractor to make sure it is
and level. Make sure you have checked with your local authorities regarding any required building
permits.
5. Make sure you have the proper tools:
• Tape Measure • 2 Small Step Ladders
• Work Gloves • Wooden Mallet
• Safety goggles • Scissors
• Phillips Screwdriver • Liquid soap or WD40 Lubricant
• Spirit Level • Hex Key (included)
NOTE: A cordless drill with Phillips head bit is highly recommended but not essential.
of 202
Safety Advice
Table of Contents
•
•
Dispose of all plastic bags safely. Keep them
out of the reach of children.
•
Keep children and pets away from the
assembly area until the work is completed.
•
Always wear shoes, gloves and safety gog gles when working.
•
Take special care not to touch overhead
•
Do not attempt to assemble the pergola in
windy or wet conditions.
•
Do not position your pergola in an area exposed to excessive wind.
•
If using power tools or a ladder, always follow
the manufacturers safety instructions.
•
Hot items such as recently used grills, blow torches etc. must not be stored in the pergola.
•
Make sure the pergola complies with local
building codes.
on
Introduction................................................. 2
Table of Contents......................................... 3
List of Parts.................................................. 4
Step 1 Assembling the Corner Posts.................... 6
Step 2 Attaching the Beams to the Corner Posts.... 8
Step 3
Step 4 Securing the Pergola to the ground........... 12
Step 5 Installing the Roof Beams......................... 13
Step 6
Building the Basic Frame
Installing the Canopy.....................................
........................... 10
16
General Order of Assembly
Step 1: Assembling the Corner Posts
Step 2: Attaching the Beams to the Corner Posts
Step 3:
Step 4: Securing the Pergola to the ground
Step 5: Installing the Roof Beams
Step 6:
Building the Basic Frame
Installing the Canopy
ATTENTION:
DO NOT ATTEMPT TO
ASSEMBLE THE
PERGOLA ALONE!
5
1
3
2
6
1
4
1
of 203
three
contact customer service before beginning assembly:
Customer Service:(877) 782 4482 Email:cs-outdoors@paragongroupusa.com
No. Part Qty
Step
No. Part Qty
Step
17 1
18 7
19 7
20 2
21 16
6
6
6
6
26 14 3
26A
7
27 1
28 16 4
We included some extra screws and bolts for your convenience.
5
4
22 24
Screw ø 1/4*x 75mm
23 94
Screw ø 1/4”x 15mm
24 14
25 15
Screw ø 4*12mm
2,5
1,2
3,5
6
6
of 205
STEP 1
Place all the parts on a level surface.
Make sure the pieces are in the correct positions before assembling.
Carefully follow the order of assembly to ensure an easy installation.
Wear proper safety gear including work shoes, gloves and goggles.
Components
Assembling the Corner Posts
Corner (1)
x 4
1.A
Place corner (1) parallel to each other the ground. Insert one roof connector (10) into each
top end as shown and fasten with screws (23).
10
Roof connector (10)
x 4
Support plate (8)
x 4
23
Support frame (9)
10
11
x 4
Screw (23)
x 24
23
Create 4 sets
x 4
1
1
1
1
of 206
Loading...