Paragon Outdoor GZ3SIZE User Manual
Gazebo GZ3
Aluminium Composite Roof Panels
Assembly Instructions
10’8’’
10’
13’1’’
12’5’’
7’
9’5’’
Paragon Group USA
Customer Service:(877) 782 4482 Email:cs-outdoors@paragongroupusa.com
Introduction
Thank you for purchasing the Gazebo GZ3.
When properly assembled and maintained, this gazebo will provide many years of enjoyment!
These instructions include helpful hints and important information needed to safely assemble and properly
maintain the gazebo. Please read these instructions completely before you begin.
Our patented gazebo has been designed for easy assembly. All steps can be completed by a team of
four people. The assembly should take about two hours.
Before Starting Assembly:
CAREFULLY READ ALL THE INSTRUCTIONS BEFORE YOU BEGIN AND FOLLOW THE
STEPS IN THE ORDER THEY ARE PRESENTED.
1. Make sure you have all the necessary parts:
Compare the contents of the three cartons to the List of Parts. If any parts are missing or damaged, or
you have any questions, please contact Customer service:
2. Lay the parts out in separate staging areas:
The List of Parts has the corresponding step number referenced to each part. We recommend that
while you go through the list, make staging areas for each step and place the parts necessary for
each step in these areas. This will save you time and effort during assembly.
(877)782 4482
before beginning assembly.
3. Select a Location:
When selecting a location for your gazebo, a flat level area is essential and if possible with proper
water drainage and easy access to power and water, if neccessary.
Choose a sunny, level position away from overhanging trees and power lines and protected from the
wind as much as possible. Locate underground pipes or cables before preparing the site or anchoring
the gazebo.
Note: You may assemble the gazebo on a hard level surface and move it to its final location when
finished. Make sure that there are no obstacles between the assembly area and the final position.
4. Prepare a Foundation:
After choosing a location, proper preparation of the site is recommended. The site must be level.
If the site is not level, create a base sligh
perimeter of two by fours filled with either soil, sod or gravel.
Make sure the base is square by measuring the diagonals from both directions and making sure
they are equal. The gazebo is secured with pegs into holes cast with concrete.
If you decide to have a concrete base, it is best to contact a reliable contractor to make sure it is flat
and level. Make sure you have checked with your local authorities regarding any required building
permits.
tly larger than the outside dimensions of the gazebo using a
5. Make sure you have the proper tools:
• Tape Measure • 2 Small Step Ladders
• Work Gloves • Wooden Mallet
• Safety goggles • Scissors and knife
• Phillips Screwdriver • Liquid soap or WD40 Lubricant
• Spirit Level • Hex Key (incl
uded)
NOTE: A cordless drill with Phillips head bit is highly recommended but not essential.
2 of 24
3 of 24
four
contact customer service before bedinning assembly:
Customer Service:(877) 782 4482 Email:cs-outdoors@paragongroupusa.com
1
2
3
4
5
Corner
Profile
2190mm
Support Frame
Support Plate
Corner Roof
Connector
Long Rail
2082mm
1
4
1
4
1
4
1
4
2
2
10
Outer Roof Connector
11A
2092mm
11
Roof
Gable Profile
2346mm
12A
1530mm
12
Roof
Gable Profile
1696mm
13A
1154mm
13
Roof
Gable Profile
1164mm
14A
1154mm
14
Roof
Gable Profile
1164mm
14
2
4
5,7
4
2
5,7
2
4
5,7
4
4
5,7
4
6
Long Rail
1902mm
7
Short Rail
1707mm
8
Short Rail
1532mm
9
Inner Roof Connector
2
2
2
10
2
2
2
2
4 of 24
15
Aluminium Composite
Roof Panel
16
Aluminium Composite
Roof Panel
17
Aluminium Composite
Roof Panel
18
Aluminium Composite
Roof Panel
black
side
black
side
black
side
black
side
7
2
7
2
4
7
4
7
19
Aluminium Composite
Roof Panel
20
5
7
2
M6*33mm
32
M6*38mm
5
2
31
8
52
7
Top center connector
21
Roof Top Cover
22
Roof Top Connector Beam
23
U-shaped Connector
24
1052mm
5
33
M6*45mm
5
1
34
Φ4*8mm
35
5
1
M6
36
5
2
37
6
2
38
6
14
10
32
10
4
7
5
3
8
8
25
26
27
28
29
30
886mm
886mm
M6*8mm
M6*18mm
M6*25mm
2
2
4
20
136
24
6
6
6
2,5
2,3
5,6
1
39
40
41
42
43
44
T - connector
X - connector
16
16
1
1
2
4
4
4
5
5
5 of 24
STEP 1
Assembling the Corner Profiles
Components
x 4
ATTENTION:
Place all the parts on a level surface
Make sure the pieces are in the correct positions before assembling.
Carefully follow the order of assembly to ensure an easy installation.
Wear proper safety gear including work shoes, gloves and goggles.
Roof connector (4)
x 4
The corner profile (1) has two screw
.
Support plate (3)
holes to connect it to the roof connector (4)
and 8 pre-drilled screw holes to attach rails (5,6,7,8)
in step 3 at its top end.
It has four screw holes to connect it to the support
plate (3) at its bottom end.
x 4
Support frame (2)
x 4
1
Top end Bottom end
Screw (30)
x 24
1
1.A
Place corner profiles (1) parallel to each other the ground. Attach one roof connector (4) to each top
end as shown and fasten with screws (30).
30 30
4
4
1 1
x 4
1 1 1 1
6 of 24
1.B
Slide support frames (2) over lower end of corner profiles (1).
Attach support plates (3) to corner profiles as shown, using four tapping screws (30) for each plate,
make sure all tappnig screws are perpendicularly into the proflie holes.
30
2
1
3
1
1
30
Leave support frames (2) about 10”over lower end of corner profiles (1) until step 4 (
the gazebo to the ground)
1
2
3
Securing
x 4
1 1 1 1
7 of 24
10 14
28
28
28
29
48
29
29
28
8 of 24
28
29
29
Loading...