Paradyne BitStorm 2600 User Manual

Download

Page 1

BitStorm™ 2600

IP DSLAM

Installation Guide

Document No. 2600-A2-GN20-20

June 2004

Page 2

Notice

This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.

Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of Paradyne Corporation to notify any person of such revision or changes.

Changes and enhancements to the product and to the information herein will be documented and issued as a new release to this manual.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods:



Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com/warranty.)



Telephone: Call our automated system to receive current information by fax or to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the number and title of this document in your correspondence. Please include your name and phone number if you are willing to provide additional clarification.

Tradem ark s

ACCULINK, COMSPHERE, FrameSaver, Hotwire, Jetstream, MVL, NextEDGE, OpenLane, Performance Wizard are registered trademarks of Paradyne Corporation. BitStorm, EtherLoop, GranDSLAM, GrandVIEW, iMarc, ReachDSL, StormTracker, and TruePut are trademarks of Paradyne Corporation. All other products and services mentioned herein are the trademarks, service marks, registered trademarks, or registered service marks of their respective owners.

A June 2004 2600-A2-GN20-20

Page 3

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or included in the manual.

2. This product is intended to be used with a 3-wire grounding type plug — a plug that has a grounding pin. This is a safety feature. Equipment grounding is vital to ensure safe operation. Do not defeat the purpose of the grounding type plug by modifying the plug or using an adapter. Prior to installation, use an outlet tester or a voltmeter to check the AC receptacle for the presence of earth ground. If the receptacle is not properly grounded, the installation must not continue until a qualified electrician has corrected the problem.

If a 3-wire grounding type power source is not available, consult a qualified electrician to determine another method of grounding the equipment.

3. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.

4. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord.

5. Do not attempt to service this product yourself, as it will void the warranty. Opening or removing covers may expose you to dangerous high voltage points or other risks. Refer all servicing to qualified service personnel.

6. General purpose cables are described for use with this product. Special cables, which may be required by the regulatory inspection authority for the installation site, are the responsibility of the customer. To reduce the risk of

fire, use a UL Listed or CSA Certified, minimum No. 26 AWG (0.128 mm comparable cables certified for use in the country of installation.

7. When installed in the final configuration, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance.

8. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If products installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary, implement corrective action prior to interconnecting the products.

9. In addition, if the equipment is to be used with telecommunications circuits, take the following precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

— Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the

network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of

electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

10. CLASS 1 LASER PRODUCT: This product has provisions for the customer to install a Class 1 laser transciever,

which provides optical coupling to the telecommunication network. Once a Class 1 laser product is installed, the equipment is to be considered to be a Class 1 Laser Product (Appareil à Laser de Classe 1). The customer is responsible for selecting and installing the laser transciever and for insuring that the Class 1 AEL (Allowable Emission Limit) per EN/IEC 60825 is not exceeded after the laser transponders have been installed. Do not install laser products whose class rating is greater than 1. Refer to all important safety instructions that accompanied the transciever prior to installation. Only laser Class 1 devices, certified for use in the country of installation by the cognizant agency are to be utilized in this product.

11. Input power to the ALARM relay interface (located on the front panel of the enclosure) must not exceed 30V rms or 60 VDC.

12. The equipment is intended for installation in a max. 65° C ambient temperature, in an environment that is free of dust and dirt.

) telecommunication cable, or

2600-A2-GN20-20 June 2004 B

Page 4

13. The power supply cord for countries other than North America is to be a minimum H05 V V-F type, min. 0.75 mm2, 2-conductor and earth ground terminated in an IEC 320 connector on one end, and a plug which is certified for use in the country of installation at the other end.

14. Do not physically stack more than eight (8) 26x1 units high. Physical stability has not been evaluated for stacking higher than eight units, and any configuration greater than eight may result in an unstable (tip-over) condition. Ensure that the four (4) rubber feet supplied with the product have been installed on the bottom of each unit prior to stacking any 26x1 units on top of one another.

EMI Notices

UNITED STATES – EMI NOTICE:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements that no modifications will be made to the equipment unless the changes or modifications are expressly approved by Paradyne Corporation.

If the equipment includes a ferrite choke or chokes, they must be installed per the installation instructions.

CANADA – EMI NOTICE:

This Class A digital apparatus meets all requirements of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du réglement sur le matérial brouilleur du Canada.

Notices to Users of the Canadian Telephone Network

NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.

NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment and includes the effect of the POTS splitter. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.

When the equipment is used in a customer premises environment, a Model 6051 POTS Splitter must be used to ensure CS-03 compliance. Refer to the POTS splitter installation instructions for details.

CE Marking

When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Library → Technical Manuals →

CE Declarations of Conformity.

C June 2004 2600-A2-GN20-20

Page 5

Japan

Class A ITE

This is a Class A product based on the standard of the Voluntary Control Council for interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

2600-A2-GN20-20 June 2004 D

Page 6

E June 2004 2600-A2-GN20-20

Page 7

About This Guide

1 Installation

 Document Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . . iii

 Document Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

 Related Product Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

 Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

 Cables Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

 Unpacking the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

 Mounting Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

 Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

 Installing the Brackets for Rack Mounting . . . . . . . . . . . . . . . . . . . . . . 1-6

 Installing the BitStorm 2600 Into a Rack . . . . . . . . . . . . . . . . . . . . . . . 1-8

 Installing the BitStorm 2600 on a Wall . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

 Installing the BitStorm 2600 on a Shelf or Desktop . . . . . . . . . . . . . . . 1-12

2 Cabling

 Cabling Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

 DSL Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

 GigE Uplink (Port 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

 10/100BaseT Uplink (Port 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

 Chaining BitStorm 2600s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

 Management Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

 Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Connecting a Terminal or PC to the Console Port. . . . . . . . . . . . . 2-7

Connecting a Modem to the Console Port . . . . . . . . . . . . . . . . . . . 2-8

 Alarm Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

 Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

 Connecting to Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

2600-A2-GN20-20 June 2004 i

Page 8

Contents

3 LEDs

 LED Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

 LED Meanings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

4 Configuration

 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

 Using the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

 BitStorm 2600 Startup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

 Startup Procedure for Inband Management . . . . . . . . . . . . . . . . . . . . . 4-5

 Startup Procedure for Out-of-Band Management . . . . . . . . . . . . . . . . 4-5

 Using the Web Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

 System / Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

 Configuration / Management / SNMP . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Configure Management Default Gateway Address . . . . . . . . . . . . 4-2

Configure Management Inband Address . . . . . . . . . . . . . . . . . . . . 4-3

Configure Management Out-of-Band Address . . . . . . . . . . . . . . . 4-3

Management Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

A Connectors and Pin Assignments

 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

 DSL Ports and POTS Splitter Connectors . . . . . . . . . . . . . . . . . . . . . . A-2

 Port 1 and Port 2 10/100BaseT Connectors . . . . . . . . . . . . . . . . . . . . A-3

 Port 3 1000BaseT Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

 Port 3 GigE SFP Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4

 Console Port Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5

 ALARM Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6

B Equipment List

C Technical Specifications

Index

ii June 2004 2600-A2-GN20-20

Page 9

About This Guide

Document Purpose and Intended Audience

This document is written for technicians who install the BitStorm 2600 IP DSLAM.

Document Summary

Section Description

Chapter 1, Installation Describes the physical installation of the BitStorm 2600 into

a rack.

Chapter 2, Cabling Describes how to install all cables for the BitStorm 2600.

Chapter 3, LEDs Explains the meaning and usage of the front panel LEDs.

Chapter 4, Configuration Describes the minimal configuration steps required to

prepare the BitStorm 2600 for remote access, using the command line interface and web interface.

Appendix A, Connectors

and Pin Assignments

Appendix B, Equipment List Provides part numbers for the BitStorm 2600 and related

Appendix C, Tec hn ic al

Specifications

Index Lists key terms, acronyms, concepts, and sections in

A master glossary of terms and acronyms used in Paradyne documents is available on the World Wide Web at www.paradyne.com. Select Support →

Technical Manuals → Technical Glossary.

Provides pinouts for connectors on the BitStorm 2600.

products.

Lists the technical characteristics of the BitStorm 2600.

alphabetical order.

2600-A2-GN20-20 June 2004 iii

Page 10

About This Guide

Installation

Overview

The BitStorm™ 2600 is a family of stackable IP DSLAMs designed for installation in a Central Office (CO), multi-tenant unit (MTU), multi-dwelling unit (MDU), or remote terminal environment. The BitStorm 2600 is available with or without internal POTS splitters.

PORT1-10/100BT

PORT2-10/100BT PORT3

1000BT

GigE

LINK

ACT

CONSOLE

ALARM

STATUS

ALARM

TEST

7 1 0

DSL PORTS 1-24

POTS 1-24

03-17435

The ReachDSL™ Model 2611 is interoperable with the Hotwire

6381 ADSL/R modem, as well as with all other Customer Premises Equipment (CPE) containing Asymmetric Digital Subscriber Line/ReachDSL (ADSL/R™) chipsets.

The ADSL Model 2621 is interoperable with the Hotwire 6381 ADSL/R modem, as well as any standard ADSL CPE. It supports ADSL, ADSL2, and ADSL2+.

The SHDSL Model 2671 is interoperable with any standard SHDSL CPE. It supports SHDSL (G.991.2).

A Command Line Interface (CLI) and a web browser interface are provided. The unit also may be managed using a network manager such as the Paradyne GrandVIEW™ Element Management System (EMS).

Up to eight BitStorm 2600 units can be logically stacked, with aggregation for up to 192 ports of DSL traffic. ReachDSL, ADSL, and SHDSL units can be included in the same stack.

2600-A2-GN20-20 June 2004 1-1

Page 12

1. Installation

Preparation

BitStorm 2600 IP DSLAM models and features are listed in Table 1-1, BitStorm

2600 Models and Features.

Table 1-1. BitStorm 2600 Models and Features

Model Number Type Number of Ports POTS Splitters

2611-A1-420 ReachDSL 24 No

2611-A1-430 ReachDSL 24 Yes

2621-A2-420 ADSL 24 No

2621-A2-430 ADSL 24 Yes

2671-A1-420 SHDSL 24 No

Consider the following before installing the BitStorm 2600 IP DSLAM:

 Installation Site

Your installation site should be well ventilated, clean, and free of environmental extremes.

 Installation Options

The BitStorm 2600 may be:

— Mounted with the included mounting brackets in a standard 19-inch

(483 mm) or 23 -inch (584 mm) rack (including both Bay Networks and Nortel 23-inch racks), or, with separately purchased mounting brackets, in a 21-inch (535 mm) ETSI rack. ETSI brackets are available from Paradyne. See Appendix B, Equipment List.

As many BitStorm 2600 units may be mounted in a standard rack as there are 1.75-inch (44.45 mm) spaces in the rack, so long as adequate cooling is provided.

— Mounted vertically against a wall.

The standard mounting brackets provided can be fastened to the base of the unit for wall mounting.

— Set on a shelf or desktop.

Up to five BitStorm 2600 units may be stacked on a shelf or desktop. Different models can be mixed in a stack.

 Power

The BitStorm 2600 operates from a 90 to 265 VAC, 47 to 63 Hz power source.

 Other Cabling

No cables are provided with the BitStorm 2600. See Table 1-2, Cable

Descriptions, to determine what cables you need to procure before

installation.

1-2 June 2004 2600-A2-GN20-20

Page 13

Cables Required

1. Installation

Ta bl e 1 -2 shows all the cables that may be required for your installation.

Table 1-2. Cable Descriptions

Connector Name Connector and Cable For Connecting . . .

DSL PORTS 1–24

POTS 1–24

Port 3 GigE

Port 3 1000BT

Port 2 10/100BT 8-position modular plug and

Port 1 10/100BT 8-position modular plug and

CONSOLE DB9 plug connector and

50-pin RJ21X Telco-type straight connector and 50-wire cable. Two cables required, one for DSL and one for POTS (if used).

SFP Transceiver An upstream BitStorm 2600 to a

8-position modular plug and 8-wire Category 5 or better unshielded twisted pair (UTP) cable.

8-wire Category 5 or better unshielded twisted pair (UTP) cable.

shielded cable.



The other connector depends on the serial port on your terminal or PC, but normally is a DB9 socket.



The other connector depends on the serial port on your modem, but normally is a DB25 plug. A null modem (crossover) cable is required.

Up to 24 DSL ports to Main Distribution Frame, punchdown block, or splitters.

Up to 24 POTS splitter ports to Main Distribution Frame or punchdown block.

downstream BitStorm 2600, or a downstream BitStorm 2600 to an upstream BitStorm 2600 or network.

A Network Management System (NMS) over a Local Area Network (LAN) employing 10BaseT or 100BaseT.

The BitStorm 2600 to one of the following:



A terminal or a PC with a terminal emulation program, or



A modem.

ALARM 5-position terminal block and

shielded, twisted-pair cable.

2600-A2-GN20-20 June 2004

The BitStorm 2600 to an alarm system.

1-3

Page 14

1. Installation

Unpacking the Hardware

HANDLING PRECAUTIONS FOR

STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation. When performing installation procedures, however, take proper static control precautions to prevent damage to equipment. If you are not sure of the proper static control precautions, contact your nearest sales or service representative.

The BitStorm 2600 is shipped in a cardboard shipping container. Carefully remove the unit from its shipping container and check for physical damage. If the unit shows signs of shipping damage, notify your sales representative.

Package Contents

In addition to this installation guide, the BitStorm 2600 shipping carton should contain:

 BitStorm 2600 DSLAM

 AC Power Cable

 Two sets of mounting brackets: one set suitable for a 19-inch (483 mm) rack

and one set suitable for a 23-inch (584 mm) rack (including Bay Networks and Nortel)

 Hardware kit (see Table 1-3, Contents of Hardware Kit Shipped with the

BitStorm 2600)

If anything is missing, notify your sales representative.

Before installing the BitStorm 2600, read the Important Safety Instructions in the beginning of this document.

Be sure to register your warranty at www.paradyne.com/warranty.

1-4 June 2004 2600-A2-GN20-20

Page 15

1. Installation

02-17326

02-17256

02-17257

02-17258

02-17325

02-17261

02-17262

02-17327

Table 1-3. Contents of Hardware Kit Shipped with the BitStorm 2600

Appearance Description Quantity

02-17259

Flat-head screw for attaching 19" mounting brackets to unit

Machine screw with captive starwasher (6-32 x 1/4″) for attaching 23" mounting brackets to unit

Self-retaining nut for racks without threaded holes 4

Dress screw (12-24 x 1/2″) for use with self-retaining nuts

Machine screw with captive starwasher (10-32 x 1/2″) for use with racks with threaded holes

Captive pan-head screw for replacing long Telco screw 2

Rubber foot for desk-mount and stacking of units 4

Cable tie (8″) for strain relief and cable management 2

5-position plug for ALARM connection 1

2600-A2-GN20-20 June 2004

1-5

Page 16

1. Installation

Mounting Configurations

Three basic installation configurations are available:

 Rack mount – see Installing the Brackets for Rack Mounting on page 1-6 and

Installing the BitStorm 2600 Into a Rack on page 1-8.

 Wall mount – see Installing the BitStorm 2600 on a Wall on page 1-10.

 Shelf or desktop – see Installing the BitStorm 2600 on a Shelf or Desktop on

page 1-12.

Mounting Brackets

Your BitStorm 2600 can be installed in a rack or on the wall using mounting brackets. Two brackets suitable for a 19-inch (483 mm ) rack (marked EIA-19) and two brackets suitable for a 23-inch (584 mm) Bay Networks or Nortel rack (marked with Paradyne Part Number 868-6282-0020) are shipped with the unit. Two brackets suitable for a 21-inch (535 mm) rack (marked ETSI) are available from Paradyne as a separate feature (see Appendix B, Equipment List ).

Rack-mounting brackets may also be used to attach the unit to a wall.

NOTE:

In this guide, the term rack refers to any rack, cabinet, frame, or bay suitable for mounting telecommunications equipment.

Installing the Brackets for Rack Mounting

Procedure

To install the mounting brackets for rack mounting:

1. Locate the black screw nearest the front panel on each side of the unit, as shown.

1 3

1 5

7 1 0

1 1 4

3 1 6

2 2

T S

- 2

03-17445

2. Remove these two black screws (one from each side) before attempting to install the mounting brackets.

1-6 June 2004 2600-A2-GN20-20

Page 17

1. Installation

3. Identify six flat-head screws (for 19-inch racks) or six machine screws (for 23-inch racks) provided with the mounting brackets in the hardware kit.

4. Attach the brackets appropriate to your rack size. Tighten all screws firmly.

19-inch (483 mm) Rack Mount

23-inch (584 mm) EIA and Bay Networks

Rack Mount

21.1-inch (535 mm) Rack Mount

23-inch (584 mm) Nortel

Rack Mount

02-17324

2600-A2-GN20-20 June 2004

1-7

Page 18

1. Installation

Installing the BitStorm 2600 Into a Rack

Two types of mounting screws are provided. Use:

 #10-32 mounting screws for rails with threaded screw holes

 #12-24 mounting screws and self-retaining nuts for rails with unthreaded

screw holes

Procedure

To install the BitStorm 2600 into a rack:

1. Determine where in the rack you will mount the BitStorm 2600. If your rack does not have threaded screw holes, slip self-retaining nuts onto the rails where the BitStorm 2600 will be fastened.

02-17070

2. Place the unit so that the brackets rest against the front of the rails. Insert screws in the bottom screw positions and hand-tighten them.

1-8 June 2004 2600-A2-GN20-20

Page 19

1. Installation

3. Insert and tighten the screws in the top screw positions, then tighten the bottom screws.

-10 /10

-10 /1

100

0 B

S U

T A T

-2 4

03-17436

P O R T 1

0 / 1 0 0 B T

P O R T 2

1 0 / 1 0 0 B

T 1 0 0

0 B T P O

R T 3

K T

G i g E

IN C L A

S M U T R

T A A

S T L

O T

- 2

4 O L

A L A R M

1 3

5 7

9 1 1

1 3 1 5

1 7

1 9

2 1

3 1 0 1 2

1 4 1 6

1 8 2 0

D S L P O R

T S 1

2 4

2600-A2-GN20-20 June 2004

1-9

Page 20

1. Installation

Installing the BitStorm 2600 on a Wall

Wall mounting requires two wood screws suitable for the weight of the fully cabled unit. These are not included. Use at a minimum 1/4-inch (6 mm) diameter screws in 3/4-inch (19 mm ) plywood (not drywall).

Procedure

To install the BitStorm 2600 on a wall:

1. Identify the flat-head screws provided in the hardware kit and the brackets suitable for a 23-inch rack. Two screws are required for each bracket.

2. Orient the unit so that the bottom is facing you and the faceplate is at the top.

3. Locate the supplied Right Side mounting bracket and fasten it to the right side of the unit.

04-17522

4. Locate the supplied Left Side mounting bracket and fasten it to the left side of the unit.

5. Tighten all screws firmly.

1-10 June 2004 2600-A2-GN20-20

Page 21

1. Installation

6. Install two wood screws (not provided) at the same height above the floor and

18.75 inches (476.25 mm) apart. Do not completely tighten the screws. Leave them so their heads are about 1/4 inch (6 mm) from the wall.

17.85 in (453 mm)

2600

03-17437

7. Hang the unit from the wood screws to verify that the screws are properly placed. The screws should freely slide into the top of the key slots in the brackets.

Do not fasten the unit to the wall until after it is completely cabled and tested.

2600-A2-GN20-20 June 2004

1-11

Page 22

1. Installation

Installing the BitStorm 2600 on a Shelf or Desktop

If the BitStorm 2600 will be placed on a shelf or desktop, install the provided rubber feet before putting the unit in position.

Procedure

To install the BitStorm 2600 on a shelf or desktop, as a standalone unit or in a stack:

1. Locate the rubber feet in the hardware kit provided with the unit.

2. Turn the unit upside down on a work surface. Squares stamped into the bottom of the unit show the proper positions for the feet.

3. Remove the protective sheet from the bottom of each foot, then press the foot onto a corner of the bottom of the unit.

4. Turn the unit right side up and place it in position on a shelf or desktop.

If the installation includes more than one unit, one can be stacked atop another. Up to five units can be stacked together.

03-17439

1-12 June 2004 2600-A2-GN20-20

Page 23

Cabling

Cabling Overview

The BitStorm 2600 has a large variety of possible cabling configurations. This chapter describes all possible connections, not all of which are required:

 DSL Ports on page 2-2

 GigE Uplink (Port 3) on page 2-3

 10/100BaseT Uplink (Port 2) on page 2-4

 Chaining BitStorm 2600s on page 2-5

 Management Port on page 2-6

 Console Port on page 2-7

 Alarm Interface on page 2-9

 Ground on page 2-10

 Connecting to Power on page 2-11

2600-A2-GN20-20 June 2004 2-1

Page 24

2. Cabling

DSL Ports

The BitStorm 2600 DSL connector supports the tip and ring connections of up to 24 DSL ports over a 50-position cable.

A POTS (plain old telephone service) splitter connector is also provided, for CO applications only. The internal splitter includes an ANSI T1.413-compliant Maintenance Test Signature (MTS) circuit. If your model does not contain the integrated POTS splitter, you must connect the unit to a separate POTS splitter. The Model 6051 POTS Splitter must be used for customer premises applications in Canada.

Procedure

To cable the DSL Ports:

1. Insert a cable tie (provided) through the top of the anchor mount next to the DSL PORTS 1–24 connector.

2. If the connector for your cable has a short captive screw, attach the cable to the DSL PORTS 1–24 connector and fasten it to the jack screw with its short captive screw.

#4-40

Jack Screw

Short

Screw

50-Pin

Connector

Anchor

Mount

02-17083

3. If the connector for your cable has a long captive screw, remove the provided jack screw from the threaded hole next to the DSL PORTS 1–24 connector. Attach the DSL PORTS 1–24 connector to the unit using the long, captive pan-head screw (provided).

Anchor

Mount

Long

Screw

50-Pin

Connector

02-17346

2-2 June 2004 2600-A2-GN20-20

Page 25

4. Tighten the cable tie around the connector and trim the excess.

5. If you use an internal POTS splitter, repeat Step 1 through Step 4, substituting POTS 1–24 for DSL PORTS 1–24.

6. Secure the cables as required for strain relief.

GigE Uplink (Port 3)

Port 3 comprises two interfaces, only one of which may be used at a time:

 An 8-position modular jack providing support for 1000BaseT

 A Small Form-Factor Pluggable (SFP) socket providing, with the appropriate

transceiver installed, support for 1000BaseX. A single-mode 1000BaseLX transceiver is available from Paradyne. See Appendix B, Equipment List.

2. Cabling

02-17084

Either interface can be used as the uplink for a single BitStorm 2600, or for the terminating unit in a stack of BitStorm 2600s.

Procedure

To use Port 3 as the uplink:

1. Connect the uplink cable to the BitStorm 2600:

— For a wire connection, plug the 8-position modular plug of your uplink

cable into the Port 3 1000BT modular jack. A straight-through cable can be used regardless of the destination interface, since the port automatically distinguishes between a Medium-Dependent Interface (MDI) and an MDI Crossover (MDIX).

— For a fiber connection, plug your transceiver into the Port 3 GigE SFP

socket. Plug the LC connector of your fiber optic uplink cable into the cable socket of the transceiver. Observing the minimum bend radius for your cable, fasten it with cable ties in such a way that it will not be kinked or snagged in the course of other cabling. If you do not know the specifications for your cable, maintain a radius of at least ten times the cable diameter.

2600-A2-GN20-20 June 2004

2-3

Page 26

2. Cabling

PORT1-10/100BT

PORT2-10/100BT PORT3

CONSOLE

1000BT

LINK

ALARM

GigE

ACT

STATUS

ALARM

TEST

03-17441

SFP Transceiver

LC Connector

2. Connect the other end of the uplink cable to the uplink interface, such as an Ethernet switch.

3. Port 3 (eth3) is the default uplink. If you have changed the default, use the configure uplink CLI command or the Configuration / Uplink screen of the web interface to specify eth3 as the uplink port.

10/100BaseT Uplink (Port 2)

Port 2 can be configured as the uplink for a single BitStorm 2600, or for the terminating unit in a stack of BitStorm 2600s. A straight-through cable can be used regardless of the destination interface, since the port automatically distinguishes between an MDI and an MDIX.

Procedure

To use Port 2 as the uplink:

1. Connect an 8-position modular cable to Port 2.

2. Connect the other end of the cable to the uplink interface, such as an Ethernet switch.

3. Using the configure uplink CLI command or the Configuration / Uplink screen of the web interface, specify eth2 as the uplink port.

2-4 June 2004 2600-A2-GN20-20

Page 27

Chaining BitStorm 2600s

Up to eight BitStorm 2600s can be chained together to use a single uplink. The same port (eth2 or eth3) used as the uplink for one unit must be used as the downlink for the next. For example, in this illustration:

 The top unit has Port 3 (eth3) defined as its uplink and is connected to Port 3

of the next unit in the chain using a straight-through 8-position modular cable.

 The middle unit has Port 2 (eth2) defined as its uplink and is connected to

Port 2 of the next unit.

 The bottom unit has Port 3 (eth3) defined as its uplink, which is the uplink for

the stack. That unit is using the fiber interface.

2. Cabling

P O

T 1

-10 /1

0 0B

2-1

0/10

B T

S U

P O

-1

0/10

2-1

0/1

P O

T 1-10

B T

-10 /10

M R

A R

igE

S U

M R

igE

S U

M R

T AT T

1-2

L P

1-2

-2 4

Copper cables connecting:

 Port 2 to Port 2 must be at least 3 feet (0.9 m) long

 Port 3 to Port 3 must be at least 6 feet (1.8 m) long

Shorter cables may cause data errors.

-2 4

-24

03-17440

2600-A2-GN20-20 June 2004

2-5

Page 28

2. Cabling

Management Port

Port 1 can be used to connect the BitStorm 2600 to a network management system using a 10BaseT or 100BaseT LAN. A straight-through cable can be used regardless of the destination interface, since the port automatically distinguishes between an MDI and an MDIX.

Procedure

To use Port 1 as the out-of-band management port:

1. Connect an 8-position modular cable to Port 1.

2. If the BitStorm 2600 is in a rack, fasten the cable to a rail with a cable tie.

3. Connect the other end of the cable to your Ethernet switch or a network interface card in a PC.

PORT1-10/100BT

Port 1

PORT2-10/100BT PORT3

1000BT

CONSOLE

ALARM

Ethernet Switch

GigE

S U

7 1 0

DSL PORTS 1-24

04-17521

2-6 June 2004 2600-A2-GN20-20

Page 29

Console Port

The CONSOLE port normally serves as the primary user interface with the BitStorm 2600 during installation. You can connect a terminal or PC directly to the CONSOLE port using a DTE cable (see procedure below). You can also use the CONSOLE port to attach a modem to the BitStorm 2600 for remote dial-in management of the unit using a DCE cable (see Connecting a Modem to the

Console Port on page 2-8).

Connecting a Terminal or PC to the Console Port

Procedure

To connect a terminal or PC to the CONSOLE port:

1. Configure the terminal or terminal emulation program to use the following parameters:

— Maximum speed: 9600 bps

2. Cabling

— Data bits: 8

— Parity: None

— Flow Control: None

— Stop bits: 1

2. Determine and procure the proper Data Terminal Equipment (DTE) cable type. The CONSOLE port requires a DB9 plug connector. The other connector depends on the serial port on your terminal or PC.

3. Connect the DB9 plug connector to the CONSOLE port socket. The CONSOLE port is ordinarily used only during installation, so do not fasten the connector.

4. Connect the other end of the cable to the serial port of your terminal or PC.

Serial

Por t

PORT1-10/100BT

PORT2-10/100BT PORT3

1000BT

GigE

S U

CONSOLE

ALARM

1 1

1 3

9 1 2

DSL PORTS 1-24

2600-A2-GN20-20 June 2004

03-17447

2-7

Page 30

2. Cabling

Connecting a Modem to the Console Port

Procedure

To connect a modem to the CONSOLE port:

1. Determine and procure the proper DCE cable type for your modem. The CONSOLE port requires a DB9 plug connector. The other connector depends on the serial port on your modem, but normally a DB25 plug is required. The cable must be an EIA-232-E crossover (null modem) cable.

2. Connect the DB9 plug connector to the CONSOLE port socket.

3. If the modem will be permanently connected, fasten the connector to the Management Module with its captive screws. If the BitStorm 2600 is in a rack, dress the cable to the left and attach it to the rail with a cable tie.

4. Connect the other end of the cable to the serial port of your modem.

PORT1-10/100BT

PORT2-10/100BT PORT3

1000BT

CONSOLE

ALARM

CONSOLE

Por t

Serial Port

LMP

T S

LIN

H ER

GigE

LINK

ACT

STATUS

ALARM

TEST

Modem

DSL PORTS 1-24

03-17448

2-8 June 2004 2600-A2-GN20-20

Page 31

Alarm Interface

2. Cabling

The ALARM interface consists of five contacts. Three of the contacts provide access to alarm relays that that can be used to set off Major and Minor physical alarms. The other two contacts provide access to a sense circuit that can be used to detect the open or closed condition of an external alarm relay.

A 5-position plug provided in the hardware kit is used to connect 20–28 AWG wire to the ALARM terminal block (see Table 1-3, Contents of Hardware Kit Shipped

with the BitStorm 2600, in Chapter 1, Installation ).

The contacts are closed during normal operation. They open in response to loss of power, hardware failure, or other alarm conditions. See ALARM Connector in

Appendix A, Connectors and Pin Assignments for more information.

CAUTION:

The ALARM Sense + and Sense – contacts are intended to be connected to an external alarm relay. Do not apply power to these contacts; doing so will result in damage to the unit.

Procedure

To connect the ALARM interface:

1. Strip the tips of the alarm source wires about 1/2 inch (13 mm).

2. Use a screwdriver to press the orange spring tab in while inserting the wire into the hole below it. The insulation should be fully within the plug and no bare wire should be exposed outside of the plug.

Spring

Ta b

02-17328

3. Insert the plug into the ALARM interface on the front panel of the BitStorm 2600.

4. If the BitStorm 2600 is in a rack, dress the cable to the left and secure it to the rail with a cable tie.

5. Connect the other end of the cable to your alarm monitoring system.

2600-A2-GN20-20 June 2004

2-9

Page 32

2. Cabling

Ground

Procedure

To connect the unit to a ground:

1. Crimp a ring terminal onto the stripped end of 14 AWG or heavier copper ground wire.

2. Remove the screw marked by the ground symbol ( ) at the right side of the front panel.

3. Fasten the ring terminal to the front panel using the same screw.

4. Attach the ground wire to an earth ground.

POTS 1-24

2600

To Earth Ground

03-17

2-10 June 2004 2600-A2-GN20-20

Page 33

Connecting to Power

The BitStorm 2600 can be powered by any AC power source supplying 90–265 VAC at 47–63 Hz.

Procedure

To connect the BitStorm 2600 to a power source:

1. Insert the supplied power cord into the power socket on the back of the unit.

2. Cabling

02-17248

2. If the BitStorm 2600 is in a rack, dress the power cord to the left and fasten it to the rail with a cable tie.

3. Connect the other end of the power cord to a grounded AC power source.

4. Make sure the STATUS LED on the front panel is ON (green). See Chapter 3,

LEDs.

2600-A2-GN20-20 June 2004

2-11

Page 34

2. Cabling

2-12 June 2004 2600-A2-GN20-20

Page 35

LEDs

LED Locations

The locations of the System and DSL Port LEDs on the front panel of the BitStorm 2600 are shown in Figure 3-1, Front Panel LEDs.

Link LEDs Activity LEDS DSL Ports LEDs

PORT1-10/100BT

PORT2-10/100BT PORT3

CONSOLE

1000BT

ALARM

P O

R T 1

1 0

/ 1

0 0

B T

O R

1 0

/ 1

0 0 B

1 0 0 0

B T

O R

i g E

S U

N S

L A

R M

Figure 3-1. Front Panel LEDs

LINK

GigE

ACT

TEST

ALARM

STATUS

03-17454

1 1

1 3

7 1 0

9 1 2

1 1 4

2 3

1 8

2 4

P O

T S

2 4

D S

L P

O R

T S

2 4

2600-A2-GN20-20 June 2004 3-1

Page 36

3. LEDs

LED Meanings

When power is first applied to the unit, it performs a power-on self-test. When this test is successfully completed, the Status LED blinks. The meaning of all the LEDs is shown in Table 3-1, Front Panel LEDs.

Table 3-1. Front Panel LEDs

LED Color State Meaning

Link*

Activity* Green Off

STATUS Green Off

ALARM Amber Off

TEST Amber Off

DSL Ports (LEDs numbered 1–24 correspond to DSL ports 1–24)

* The three RJ45-type connectors for Port 1, Port 2, and Port 3 bear two LEDs: the left

one is the Link LED and the right one is the Activity LED. The SFP socket for Port 3 has two adjacent LEDs marked LINK and ACT.

Green Off

Flashing

Green Off

No Ethernet link present.

Ethernet Link present.

Ethernet link is present, but port is administratively disabled.

No data is being transferred.

Data is being transferred.

No power, or the unit has not completed initialization.

Unit has power and has completed initialization.

No Alarms.

Unit failed self-test, or the unit has exceeded a safe temperature, or a fan has failed.

Normal operating mode.

At least one port is in test mode.

The port is disabled or no signal is detected on the line.

Port has successfully trained with the remote and is active.

3-2 June 2004 2600-A2-GN20-20

Page 37

Configuration

Overview

The BitStorm 2600 is designed to require minimal configuration before it can be accessed by a Network Operations Center (NOC). When the BitStorm 2600 is first powered up it is a fully functional bridge, and all DSL ports are set to their maximum speed.

Initial configuration is performed using the Command Line Interface (CLI). The CLI is available from a terminal or PC connected to the CONSOLE port.

Additional configuration may be necessary, depending on the mode used to manage the BitStorm 2600:

 Inband

 Out of band through Port 1

This can be performed using the CLI, SNMP, or the web interface.

For more configuration information, see the BitStorm 2600 and GranDSLAM 4200

IP DSLAM Command Line Interface Reference (for the CLI) and the online Help

(for the web interface).

2600-A2-GN20-20 June 2004 4-1

Page 38

4. Configuration

Using the CLI

A command line interface (CLI) can be used to configure and monitor the unit. The CLI is available from a PC or terminal connected to the Console port, or from a Telnet session with the device.

The following commands are available:

Table 4-1. CLI Commands

Command Function

clear Clear the system log.

configure Enter Configuration mode.

copy Copy from one file to another.

date Set the time zone and date format.

end If user is in Administrator mode, shifts to User mode; if user is in

User mode, positions interface at top of menu tree.

exit Terminate current session.

firmware Download or apply new firmware.

paging Enable or disable paging (more prompt) for this session.

privilege Enable administrator mode.

restart Restart a unit.

show Display configuration, statistics, and status.

technical-support Display information for contacting technical support.

test Test the system.

Descriptions of some essential configuration commands follow.

Configure Management Default Gateway Address

The configure management default gateway command specifies the IP address of the next hop router for the management traffic.

configure management default-gateway {ip_address}

Minimum Access Level: Administrator

ip_address – Specifies the IP address of the default gateway for the management ports.

Example:

PDYN# configure management default-gateway 137.90.127.1

4-2 June 2004 2600-A2-GN20-20

Page 39

Configure Management Inband Address

The configure management inband address command specifies the IP address of the unit.

configure management inband address {ip_address} { subnet_mask}

Minimum Access Level: Administrator

ip_address – Specifies the management IP address. Default is 0.0.0.0 (disabled). Do

not configure inband and out-of-band management on the same subnet.

subnet_mask – Specifies the subnet mask to be applied to the IP address. The default mask is 255.255.255.0.

Example:

PDYN# configure management inband address 137.90.127.3

255.255.255.0

4. Configuration

Configure Management Out-of-Band Address

The configure management out-of-band address command specifies the IP address of the unit that will accept management traffic on the out-of-band management port.

configure management out-of-band address {bootp | {{ip_address} { subnet_mask} }

Minimum Access Level: Administrator

bootp – Specifies that a BOOTP server will determine the management IP address.

ip_address – Specifies the management IP address. The default address is

10.10.10.10. Do not configure inband and out-of-band management on the same subnet.

subnet_mask – Specifies the subnet mask to be applied to the IP address. The default mask is 255.255.255.0.

Example:

PDYN# configure management out-of-band address bootp

PDYN# configure management out-of-band address 137.90.127.3

255.255.255.0

2600-A2-GN20-20 June 2004

4-3

Page 40

4. Configuration

BitStorm 2600 Startup Procedure

You can initialize your BitStorm 2600 via a PC or terminal connected to the unit’s CONSOLE port. Then, using a series of CLI commands, GrandVIEW EMS or another Element Management System, or the web interface, you can configure the unit according to your requirements.

Login

Procedure

To log in to the BitStorm 2600:

1. Connect a PC or terminal to the CONSOLE port. (See Console Port in

Chapter 2, Cabling.)

2. At the login> prompt, type admin and press Enter.

3. At the password> prompt, press Enter. The default login password is blank.

Management Modes

4. At the PDYN> prompt, type privilege and press Enter.

5. At the password# prompt, press Enter. The default privileged password is blank.

You are now logged on and in privileged mode, which allows you to configure the unit.

The startup procedure for the BitStorm 2600 system differs depending on the type of management used:

 Inband Management – Operates over the uplink.

 Out-of-Band Management – Operates over Port 1.

4-4 June 2004 2600-A2-GN20-20

Page 41

Startup Procedure for Inband Management

With inband management, the BitStorm 2600 is managed using the uplink port.

Procedure

To start up the BitStorm 2600 using inband management:

1. Specify the uplink port using the configure uplink command. It must be either eth2 (Port 2) or eth3 (Port 3). For example:

PDYN# configure uplink eth3

2. Assign an IP address, netmask, and next-hop router using the configure management command. For example:

PDYN# configure management inband address 137.90.127.3

255.255.255.0

PDYN# configure management default-gateway

137.90.127.1

Do not configure inband and out-of-band management on the same subnet.

4. Configuration

Startup Procedure for Out-of-Band Management

In out-of-band management, you manage the unit through Port 1.

Procedure

To start up the BitStorm 2600 using out-of-band management:

1. Assign an IP address, netmask, and next-hop router using the configure management command. For example:

PDYN# configure management out-of-band address

137.90.80.3 255.255.255.0

PDYN# configure management default-gateway 137.90.80.1

You can now access the web interface by typing into the Location field of your web browser the IP address assigned to the Port 1. See Using the Web

Interface on page 4-6.

Do not configure inband and out-of-band management on the same subnet.

2. Configure routers as necessary to route data from the NOC to the BitStorm 2600.

2600-A2-GN20-20 June 2004

4-5

Page 42

4. Configuration

Using the Web Interface

To access the web interface:

Procedure

1. Open your web browser. (Internet Explorer Version 6 or above is recommended.)

2. Type http:// and the IP address of the BitStorm 2600 into the Address field of your browser window. For example:

3. A login window appears. Enter the default User ID (admin) and leave Password blank. Click on OK. The web interface screen appears.

4. Click on the menu tab appropriate to what you would like to do:

— Configuration – To configure the system and interfaces

— Status – To display statistics, status, and contents of memory

— System – To display system information, download firmware, back up

configurations, and modify users

— Diagnostics – To start and stop tests

4-6 June 2004 2600-A2-GN20-20

Page 43

System / Users

4. Configuration

For security reasons, it is a good idea to change the default password the first time you use the system.

Procedure

To change the default password for user admin:

1. Click on the System menu tab, then click on Users. The folllowing screen appears.

2. In the Configured Users box, select admin by clicking in the circle next to it.

3. Click on Modify Selected. The System / Users / admin screen appears.

4. Type in a new Login Password and a new Privilege Password, then click on Apply. Keep a record of the new password.

2600-A2-GN20-20 June 2004

4-7

Page 44

4. Configuration

Configuration / Management / SNMP

SNMP access to the unit is disabled by default. The read-only community string is public, and the read-write string is private. Community strings, network management system addresses, and trap manager addresses can be set using the System/Management/SNMP screen.

Procedure

To set SNMP parameters:

1. Click on the Configuration menu tab, then click on SNMP. The System/Management/SNMP screen appears.

2. Enter new SNMP parameters as desired. Click on Apply.

4-8 June 2004 2600-A2-GN20-20

Page 45

Connectors and Pin Assignments

Overview

The following sections provide pin assignments for:

 DSL Ports and POTS Splitter Connectors on page A-2

 Port 1 and Port 2 10/100BaseT Connectors on page A-3

 Port 3 1000BaseT Connector on page A-3

 Port 3 GigE SFP Connector on page A-4

 Console Port Connector on page A-5

PORT2-10/100BT PORT3

PORT1-10/100BT

CONSOLE

 ALARM Connector on page A-6

1000BT

ALARM

GigE

ACT

LINK

TEST

ALARM

STATUS

Figure A-1. BitStorm 2600 IP Front Panel

DSL PORTS 1-24

POTS 1-24

2600

03-17455

2600-A2-GN20-20 June 2004 A-1

Page 46

A. Connectors and Pin Assignments

DSL Ports and POTS Splitter Connectors

The 50-pin RJ21X Telco connector labeled DSL Ports 1–24 provides the 2-wire loop interface from each DSL port to the MDF for CO applications, or the in-building wiring for customer premises applications. (The Canadian designation for this connector is CA21A.) The 50-pin RJ21X (CA21A) Telco connector labeled POTS 1–24 (if installed) provides the 2-wire loop interface with the internal POTS splitters.

Ta bl e A -1 lists the pin assignments for these interfaces. Note that Pins 25 and 50

are not used.

Table A-1. DSL Connector Pinouts

Connector Pins

DSL Port

11, 26

22, 27

(Ring, Tip)

33, 28

44, 29

55, 30

66, 31

77, 32

88, 33

99, 34

10 10, 35

11 11, 36

12 12, 37

13 13, 38

14 14, 39

15 15, 40

16 16, 41

17 17, 42

18 18, 43

19 19, 44

02-17151

20 20, 45

21 21, 46

22 22, 47

23 23, 48

24 24, 49

A-2 June 2004 2600-A2-GN20-20

Page 47

Port 1 and Port 2 10/100BaseT Connectors

Port 1 and Port 2 are 8-pin unkeyed modular jacks for a 10/100Base interface.

Table A-2. Port 1 and Port 2 Pinouts

Signal Pin

Transmitted Data + 1

Transmitted Data – 2

Received Data + 3

Unused 4

Unused 5

Received Data – 6

Unused 7

Unused 8

A. Connectors and Pin Assignments

Pin 1

Pin 8

97-15449

Port 3 1000BaseT Connector

Port 3’s 1000BaseT interface is an 8-pin unkeyed modular jack.

Table A-3. Port 3 1000BaseT Connector

Signal Pin

Tip 1 1

Ring 1 2

Tip 2 3

Ring 3 4

Tip 3 5

Ring 2 6

Tip 4 7

Ring 4 8

Pin 1

Pin 8

97-15449

2600-A2-GN20-20 June 2004

A-3

Page 48

A. Connectors and Pin Assignments

Port 3 GigE SFP Connector

Port 3’s GigE interface is a standard SFP socket.

Table A-4. Port 3 GigE Connector

Signal Pin

VeeT 1

TXFault 2

TXDisable 3

MOD-DEF(2) – I2C_DATA 4

MOD-DEF(1) – I2C_CLK 5

MOD-DEF(0) – SFP_PRESENT_L 6

Rate Select 7

LOS 8

VeeR 9

VeeR 10

VeeR 11

RD- 12

RD+ 13

VeeR 14

VccR 15

VccT 16

VeeT 17

TD+ 18

TD- 19

VeeT 20

A-4 June 2004 2600-A2-GN20-20

Page 49

Console Port Connector

The CONSOLE port connector is a DB9 socket connector that supports an EIA-232-E circuit as shown in Ta b le A - 5.

Table A-5. Console Port Connector

RS-232 Signal Direction Pin

Data Carrier Detect Out 1

Receive Data Out 2

Send Data In 3

Data Terminal Ready In 4

Ground — 5

Data Set Ready Out 6

Request to Send In 7

Clear to Send In 8

A. Connectors and Pin Assignments

Ring Indicator — 9

2600-A2-GN20-20 June 2004

A-5

Page 50

A. Connectors and Pin Assignments

ALARM Connector

The alarm relay reports major alarms through the ALARM connector.

Table A-6. ALARM Connections

Signal Direction Contact

5 4 3 2 1

Major Alarm Out 1

Common Out 2

Minor Alarm Out 3

Alarm Sense + In 4

Alarm Sense – In 5

ALARM

03-17453

The alarm contacts are closed during normal operation. They open in response to loss of power, hardware failure, or other alarm conditions. The maximum rated load for the alarm relays is:

 30 VDC: 1.0 Amp

 60 VDC: 0.6 Amp

 60 VAC: 0.6 Amp

A-6 June 2004 2600-A2-GN20-20

Page 51

Equipment List

Table B-1. BitStorm 2600 Equipment List (1 of 2)

Description Model Number

BitStorm 2600 and GranDSLAM 4200 IP Command Line Interface Reference (paper copy)

BitStorm 2600 and GranDSLAM 4200 IP SNMP Reference (paper

copy)

BitStorm 2600 ReachDSL without POTS Splitter, with North America power cord