Paradyne ACCULINK 3161 CSU, ACCULINK 3161 DSU, ACCULINK 3161 Quick Reference Manual

ACCULINK 3161 DSU/CSU

QUICK REFERENCE

Document No. 3161-A2-GL11-40

Copyright  1998 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be
copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated
into any human or computer language in any form or by any means, electronic,
mechanical, magnetic, manual or otherwise, or disclosed to third parties without the
express written permission of Paradyne Corporation, 8545 126th Avenue North, P.O.
Box 2826, Largo, Florida 33779-2826.

Paradyne Corporation makes no representation or warranties with respect to the
contents hereof and specifically disclaims any implied warranties of merchantability or
fitness for a particular purpose. Further, Paradyne Corporation reserves the right to
revise this publication and to make changes from time to time in the contents hereof
without obligation of Paradyne Corporation to notify any person of such revision or
changes.

Changes and enhancements to the product and to the information herein will be
documented and issued as a new release to this manual.

Warranty, Sales, and Service Information

Contact your sales or service representative directly for any help needed. For additional
information concerning warranty, sales, service, repair, installation, documentation, or
training, use one of the following methods:

 Via the Internet: Visit the Paradyne World Wide Web site at

http://www.paradyne.com

 Via Telephone: Call our automated call system to receive current information via

fax or to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221
— International, call 727-530-2340

T rademarks

All products and services mentioned herein are the trademarks, service marks,
registered trademarks or registered service marks of their respective owners.

TM

1

ACCULINK 3161 DSU/CSU

Quick Reference

Document Number 3161-A2-GL11-40
February 1998

Quick Start Procedure

The following procedure is for experienced DSU/CSU users who are familiar with the
3161 DSU/CSU installation process and have no special requirements for their
application. See the

ACCULINK 316x Data Service Unit/Channel Service Unit

Operator’s Guide

(3160-A2-GB21) for more information. A copy is included with the

Auxiliary Backplane.

1. Install the Auxiliary Backplane onto the 3000 Series Carrier. See the

ACCULINK

3151 CSU and 3161 DSU/CSU General Information Guide

(3100-A2-GK40) for

installation procedures.

2. Attach the DTE cable (DB15) and/or port cables (DB25) to the appropriate
connectors on the Auxiliary Backplane. See the

COMSPHERE 3000 Series Carrier

Installation Manual

(3000-A2-GA31) for detailed cable and connector information.

Connect the other end of the DTE cable to the customer premises equipment.

2

3. Attach the network cable to the Auxiliary Backplane using either a 50-pin cable or
the T1 Network Interface Adapter. Connect the other end of the network cable to
the connection provided by the telephone company.

496-14386-0

3

Auxiliary

Backplane

over Slots 9–16

COMSPHERE

3000 Series

Carrier (Rear)

T1 Network

Cable

Cable

Retainer

4. Turn on the power to the 3000 Series Carrier.

3

5. Insert the DSU/CSU circuit card into the appropriate slot in the carrier. The
power-up self-test begins.

495-1479

7

6. If you intend to use front panel emulation, connect the cable from the PC to Port 2
on the Auxiliary Backplane using the COM port adapter and COM-port-to-PC cable.

7. If you do not intend to use the DTE Drop/Insert T1 port, disable it using the
configuration procedures in Chapter 3,

Operation

, and Appendix C,

Configuration

Options

, of the

ACCULINK 316x Data Service Unit/Channel Service Unit

Operator’s Guide

(3160-A2-GB21). (The default setting for this port is Enabled.)

8. The Factory 1 configuration for ESF framing format and B8ZS line coding format is
the default configuration and is appropriate for most networks. If this configuration
does not work for you, try the Factory 2 configuration for D4 framing format and
AMI line coding format. To further customize configuration options, refer to

Changing Configuration Options

in Chapter 3,

Operation

, and Appendix C,

Configuration Options

, in the

ACCULINK 316x Data Service Unit/Channel Service

Unit Operator’s Guide

.

9. During the power-up self-test, the FAIL LED flashes, then all LEDs blink twice.
When the test is complete, verify that the DSU/CSU is functional by observing that
the OK, NETWORK SIG, and DTE SIG LEDs are lit.

10. Configure the ports and channels you intend to use and assign channels to the
network interface.

4

Configuration Options

Configuration options are accessed from the Cnfig branch of the front panel menu.

DSU ESF

Stat

97-15577

DevHS

STest Perf TSt a t LED ID

T1 PrtnPrtnUserTelco

Cur

24Tot

Intvl

FarNear

Cur

8Tot

Intvl

Test

Rlpbk Lpbk Ptrns Lamp

QRSS 511

Abort Mon

LLBUP

LLBDN

54UP

54DN

FT1UP

FT1DN

PLB DLB RLBLLBAbort DCLB DTLB

QRSS 1in8 511

Send

Cnfig

EQPT NET

Ctrl

Rel ClrReg

Reset

CID

PasswdLED

ACO

DL

Mon

Call

DiscDial ChDir

1 . . 5,A

(Directory)

1 . . 5,A

(Directory)

DTE Prt1 Prt2

User Prt1 Prt2

FarNear

Load Edit Area From:

Choose Function:

Activ Cust1 Cust2 Fact1 Fac t2

User AlarmNETDTE Port Chan Gen Mgmt

Gen Trap

DTE Pr t1

Prt2

ClearDsply

Copy Prt1 Prt2

Port Select :

All Prt1 Prt2

Save

Cust1Activ Cust2

Edit