Paradyne 6212 User Manual

Hotwire

6212 ADSL Router

User’s Guide

Document Number 6212-A2-GB20-20

July 2004

Notice

This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773. Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of Paradyne Corporation to notify any person of such revision or changes. Changes and enhancements to the product and to the information herein will be documented and issue d as a new release to this manual.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods:

• Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com/warranty.)

• Telephone: Call our automated system to receive current information by fax or to speak with a company representative.

Within the U.S.A., call 1-800-870-2221 Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the number and title of this document in your correspondence. Please include your name and pho ne number if you are willing to provide additional clarification.

Trademarks

Acculink, Comsphere, ETC, Etherloop, FrameSaver, GranDSLAM, Hotwire, the Hotwire logo, Jetstream, MVL, NextEDGE, OpenLane, Paradyne, the Paradyne logo, Paradyne Credit Corp., the Paradyne Credit Corp. logo, Performance Wizard, StormPort, TruPut are all registered trademarks of Paradyne Corporation. ADSL/R, BitStorm, Connect to Success, GrandVIEW, Hotwire Connected, iMarc, JetFusion, JetVision, MicroBurst, PacketSurfer, ReachDSL, Spectrum Manager, StormTracker and TriplePlay are trademarks of Paradyne Corporation. All other products and services mentioned herein are the trademarks, service marks, registered trademarks, or registered service marks of their respective owners.

CE Marking

When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Library → T echnical Manuals →

CE Declarations of Conformity.

2 July 2004 6212-A2-GB20-20

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or included in the manual.

2. Slots and openings in th e cabin et are provided for ventilation. To ensure reliable operation of the product

and to protect it from overheating, these slots and openings must not be blocked or covered.

3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk

on the power cord.

4. Do not attempt to service this product yourself, as opening or removing cov ers may expose you to

dangerous high voltage points or other risks. Refer all servicing to qualified service personnel.

5. General pu rpose cab les are used with this product for connection to the network. Special cables, which

may be required by the regulatory inspection authority for the installation site, are the responsibility of the customer. Use a UL Listed, CSA certified, minimum No. 24 AWG line cord for connection to the Digital Subscriber Line (DSL) network.

6. When installed in the final configuration, the product must comply with the applicable Safety Standa rds

and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance.

7. A rare phenome non can create a voltage potential between the earth grounds of two or more buildings.

If products installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary, implement corrective action prior to interconnecting the products.

8. Input power to this product must be provided by one of the following: (1) a UL Listed/CSA certified

power source with a Class 2 or Limited Power Source (LPS) output for use in North America, or (2) a certified transformer, with a Safety Extra Low Voltage (SELV) output having a maximum of 240 VA availabl e, for use in the country of installation.

9. In addition, since the equipment is to be used with teleco mmunications circuits, take the following

precautions:

— Never install telephone wiring during a lightning storm. — Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. — Never touch unin sulate d telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

— Use caution when installing or modifying telephone lines. — Av oid using a telephone (other than a cordless type) during an electrical storm. There may be a

remote risk of electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

6212-A2-GB20-20 July 2004 3

CE Marking

FCC Part 15 Declaration

An FCC Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Support -> Technical Manuals -> Declarations of Conf ormity.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device m ust accept any interference received, including interference that may cause undesired operation.

The authority to operate this equipment is conditioned by the requirement that no modifications will be made to the equipment unless the changes or modifications are expressly approved by the responsible party.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit diffe rent from that to whi ch the recei ver is connected.

• Consult the dealer or an experienced rad i o/TV technician for help.

4 July 2004 6212-A2-GB20-20

Notice to Users of the United States Telephone Network

The following notice applies to versions of the modem that have been FCC Part 68 approved. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the

Administrative Council for Terminal Attachment (ACTA). On the bo ttom side of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the Telephone Company.

This equipment is intended to connect to the Public Switched Telephone Network through a Universal Service Order Code (USOC) type RJ11C jack. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modul ar plug is provided with this product. It has been de signed to be connected to a compatible modular jack that is also compliant.

The Ringer Equivalence Number (or RE N) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local Telephone Company. Th e REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point. For example, 03 represents a REN of 0.3.

If the modem causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The Telephone Company may make changes in its facilities, equip ment, operations or procedures that could affect the operation of the equipment. If this happens, the Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with the modem, refer to the repair a nd warranty information in this document.

If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is resolved.

The user may make no rep airs to the equipment. Connection to party line service is subject to state tariffs. Contact the state public utility commissi on, public

service commission or corporation commission for information. If the site has specially wired alarm equipment connected to the telephone line, ensure the installation of

the modem does not disable the alarm equipment. If you have questions about what will disabl e alarm equipment, consult your Telephone Company or a qualified installer.

6212-A2-GB20-20 July 2004 5

Notice to Users of the Canadian Telephone Network

NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical

Specifications. This is confirmed by the registration numbe r. The abbreviation IC before the registration number signifies that registration wa s performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.

NOTICE: The Ringer Equivalence Number (REN) f or this terminal equipment is labeled on the equipment. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interf ace. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.

If your equipment is in need of repair, contact your local sales representative, service representative, or distributor directly.

CANADA – EMI NOTICE:

This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du Canada.

Japan Notices

6 July 2004 6212-A2-GB20-20

Table of Contents

Chapter 1 Introduction ....................................................10

1.1 Product Overview.............................................................. 10

1.2 Features .......................................................................... 11

1.3 Application....................................................................... 12

1.4 Front Panel LED Indicators.................................................. 13

Chapter 2 Hardware Installation......................................14

2.1 Installation....................................................................... 14

2.2 Installing the USB Driver.................................................... 15

2.2.1 Auto Installation................................................................ 16

2.2.2 Manual Installation............................................................ 18

2.3 Uninstalling the USB Driver................................................. 25

2.3.1 Auto-Uninstallation............................................................ 25

2.3.2 Manual Removal of the Driver ............................................. 27

Chapter 3 Login Via the Web Browser..............................28

3.1 IP Address ....................................................................... 28

3.2 Login Procedure................................................................ 29

Chapter 4 Basic Configuration..........................................30

4.1 Software Version Information.............................................. 30

4.2 Change the Password......................................................... 31

4.3 ADSL Link Status .............................................................. 32

4.4 WAN Setup....................................................................... 33

4.4.1 RFC 1483 Bridged ............................................................. 34

4.4.2 RFC 1483 Routed .............................................................. 34

4.4.3 PPPoE.............................................................................. 35

4.4.4 PPPoA.............................................................................. 36

4.4.5 MER ................................................................................ 36

4.5 LAN IP Address................................................................. 36

4.6 Routing............................................................................ 37

4.6.1 Enable RIP ....................................................................... 37

4.6.2 Static route configuration................................................... 38

4.7 Save ............................................................................... 40

4.8 Reboot............................................................................. 40

4.9 Retrieve default settings..................................................... 41

Chapter 5 Advanced Configuration...................................42

5.1 ADSL Mode....................................................................... 42

5.2 VLAN............................................................................... 43

6212-A2-GB20-20 July 2004 7

5.3 DHCP .............................................................................. 43

5.3.1 Enable DHCP .................................................................... 44

5.3.2 Disable the DHCP.............................................................. 46

5.4 DHCP Relay...................................................................... 46

5.5 SNMP .............................................................................. 47

5.5.1 Modifying SNMP Parameters................................................ 47

5.5.2 Modifying Traps ................................................................ 48

5.5.3 Modifying Communities...................................................... 49

5.6 Firewall............................................................................ 50

5.6.1 View Firewall Actions ......................................................... 51

5.6.2 IP Filtering ....................................................................... 52

5.7 NAT................................................................................. 54

5.7.1 Static NAT Mapping ........................................................... 54

5.7.2 Port Range Mapping........................................................... 55

5.8 Configure......................................................................... 56

5.8.1 Configure Interface............................................................ 57

5.8.2 DNS & Default Gateway ..................................................... 59

5.8.3 NAT................................................................................. 60

5.9 VCC ................................................................................ 61

5.9.1 List IPoA.......................................................................... 61

5.9.2 Delete Encapsulation ......................................................... 62

5.9.3 Add a VCC........................................................................ 62

5.9.4 Delete a VCC.................................................................... 65

5.9.5 Show VCC quality.............................................................. 65

5.9.6 PPPoE.............................................................................. 65

5.9.7 PPPoA.............................................................................. 66

5.10 IGMP............................................................................... 67

5.10.1 Add an IGMP entry ............................................................ 67

5.10.2 Delete an IGMP entry......................................................... 68

5.11 Bridging........................................................................... 68

5.11.1 Bridge ............................................................................. 68

5.11.2 Spanning tree................................................................... 70

5.11.3 View STP parameters......................................................... 71

5.11.4 To configure STP parameters .............................................. 72

5.11.5 Enable/Disable STP............................................................ 72

Chapter 6 Performance monitoring ..................................73

6.1 ADSL Link Status .............................................................. 73

6.2 System Statistics .............................................................. 74

6.2.1 Interface Statistics ............................................................ 74

6.2.2 TCP-IP............................................................................. 76

8 July 2004 6212-A2-GB20-20

6.2.3 DHCP-Lease ..................................................................... 77

6.3 ATM statistics ................................................................... 77

6.3.1 AAL5 ............................................................................... 77

6.3.2 Encapsulation ................................................................... 78

Chapter 7 Diagnostics ......................................................79

7.1 OAM Loopback.................................................................. 79

7.2 Ping ................................................................................ 80

Chapter 8 Firmware Upgrade ...........................................82

8.1 TFTP Upgrade Via Web....................................................... 82

8.2 Upgrade Via FTP................................................................ 83

Chapter 9 Accessing the Logging Record .........................85

9.1 Log Record from Telnet...................................................... 85

Appendix A: Specifications ...............................................89

Appendix B: Pin Assignments ...........................................91

Appendix C: Troubleshooting............................................92

Glossary ....................................................................93

6212-A2-GB20-20 July 2004 9

Chapter 1 Introduction

This chapter introduces the Hotwire® 6212 ADSL Router. It includes a product overview, a description of the product’s features and applications, and an explanation of the functions of the Front panel LED indictors.

1.1 Product Overview

The Hotwire 6212 ADSL Router is an ADSL router integrated with a USB and an Ethernet Interface. The USB and four Ethernet ports can be used simultaneously, allowing a total of five PCs to be connected to the Hotwire 6212 and access the ADSL line. In addition, the Hotwire 6212 can be configured to operate in bridge mode or router mode.

The auto configuration/auto upgrade function allows multiple ADSL routers to be upgraded over the LAN in one operation.

The Hotwire 6212 protects all of your networked computers with advanced security technologies such as virtual private network s (VPNs ) wi th PPTP passthrough , L2TP passthrough, and IPSec passthrough.

10 July 2004 6212-A2-GB20-20

1.2 Features

The ADSL Router is a compact and high performance standalone unit that provides:



Four Ethernet ports and one USB port for LAN connection



One console port for local management



Stateful packet inspection and filtering



Denial of Service protection



IGMP Proxy



G.dmt, G.lite, and T1.413



Remote configuration and upgrade



Auto-negotiation rate adaptation



AAL5 for ATM over ADSL



UBR, CBR, VBR-real-time, VBR-non-realtime ATM services



VC-based and LLC multiplexing



Up to 8 VCs



Embedded SNMP agent



Configuration backup and restoration



OAM F4/F5



Static route/RIP/RIP v2 routing functions



NAT/PAT



On-demand PPPoE



PVC can support multiple PPPoE sessions



DHCP Server/Relay



DNS Proxy



FTP Server



TFTP Client



IEEE 802.1d compliant

6212-A2-GB20-20 July 2004 11

1.3 Application

The figure below shows a possible application of the router.

12 July 2004 6212-A2-GB20-20

1.4 Front Panel LED Indicators

LED Indicator Color Mode Function

Green On Power is supplied Power Off Power is not supplied

LAN 1x – 4x Green

ADSL Link Green

On An Ethernet link is established Off An Ethernet link is not established Flash Activity over the Ethernet link On A USB link is connected USB Green Off A USB link is not connected Flash The ADSL Link is training On The ADSL Link is established Off The ADSL link is not connected Flash Packets transmitted or received on the ADSL link ADSL TX/RX Green Off No packets on the ADSL link

6212-A2-GB20-20 July 2004 13

Chapter 2 Hardware Installation

2.1 Installation

The Hardware installation procedure is explained below.

Caution: Always disconnect all telephone lines from the telephone wall outlet before

servicing or disassembling this device.

1. Verify that the On/Off switch on the rear panel is in the Off position.

2. Connect the power adapter to the Power jack of the device, a nd then plug the power adapter into the wall outlet.

3. Connect the USB port to a PC with a standard USB cable.

4. Connect the LAN ports to PCs or a hub using RJ45 cables. The LAN ports automatically sense whether the connection requires a crossover, so either straight-through or crossover cables may be used.

5. Connect the LINE port to your telephone jack with an RJ11 connector cable.

6. Turn the On/Off switch on the rear panel to the On position.

Note If the device fails to power on, or it malfunctions, first verify that the power supply

is correctly connected, and then power it on again.

14 July 2004 6212-A2-GB20-20

2.2 Installing the USB Driver

Before you connect your router’s USB cable to your PC, you must load the ADSL USB drivers and configure the device via the LAN port using Web management. There are two ways to install the USB driver:

• Auto-installation: Install the driver by inserting the CD in the CD drive of your PC and letting the installation automatically start.

• Manual installation: Install the driver with the Windows Hardware Wizard. When using the USB port the LAN port must be vacant.

6212-A2-GB20-20 July 2004 15

2.2.1 Auto Installation

STEP 1: Insert the CD-ROM disc for the ADSL USB router.

STEP 2:

continue. (If the screen doesn’t appear, browse the CD-ROM and double-click on INSTALL.EXE.)

The CD-ROM will auto-play and you will see the following screen. Click on Next to

16 July 2004 6212-A2-GB20-20

STEP 3: When prompted by the message shown below, connect yo ur router to a USB port of

your PC. Then click on OK.

STEP 4:

A completion message appears when the installation is complete. Click on F inish.

6212-A2-GB20-20 July 2004 17

2.2.2 Manual Installation

To connect the router to a PC using the USB interface, you need to use a standard USB cable and install the USB interface software. Follow the steps below.

STEP 1

cable into a USB port on your PC, and plugging t he square connector into the router. The Found New Hardware screen appears:

STEP 2

: Connect the USB router to the PC by plugging the flat connector of a standard USB

: When the screen appears as below, click on the Next button.

18 July 2004 6212-A2-GB20-20

STEP 3: When the screen appears as below, select Search for a suitable driver and click the Next button.

6212-A2-GB20-20 July 2004 19

STEP 4: Select Specify a location and click on the Next button. If you are installing the

software from a disk, insert the disk.

STEP 5

: Select the location of the file using the Browse button.

20 July 2004 6212-A2-GB20-20

STEP 6: Enter the correct file for your operating system, select the ADIRNDIS.INF file, and click on the Open button.

STEP 7

: When the screen below appears, click on the OK button.

6212-A2-GB20-20 July 2004 21

STEP 8: When the screen below appears, click on the NEXT button.

22 July 2004 6212-A2-GB20-20

STEP 9: Click the Finish button when prompted.

Installation is complete.

6212-A2-GB20-20 July 2004 23

Note: At the end of the installation, a warning message of digital signatiure may appear. Click on Yes to close the message and complete the installation.

24 July 2004 6212-A2-GB20-20

2.3 Uninstalling the USB Driver

2.3.1 Auto-Uninstallation

If the software was installed with the auto-play driver, uninstall it by completing the following steps:

STEP 1:

Click on the Windows Start button and go to Programs>CT-562. Click on Uninstall.

STEP 2:

Click on OK when you are prompted to confirm the removal of the software.

6212-A2-GB20-20 July 2004 25

STEP 3: When prompted by the message shown below, disconnect the USB cable from your PC and click on the OK button.

STEP 4: When the driver is removed, a completion message appears. Click on Finish to close the window.

26 July 2004 6212-A2-GB20-20

2.3.2 Manual Removal of the Driver

If the driver was manually installed, it must be uninst a lled manually. To do that, go to the Windows Device manager, choose ADI USB Remote NDIS Network Device, and delete it.

6212-A2-GB20-20 July 2004 27

Chapter 3 Login Via the Web Browser

This section describes how to manage the router via a web browser from the remote end. You can use a web browser such as Microsoft Internet Explorer, or Netscape Navigator. It is best to set your display resolution to 1024 x 768. To change the resolution, go to the Microsoft Windows control panel and click on the Display icon, then change the display settings. Access to the management functions of the USB router from the LAN side is restricted. A unique default user account is assigned with user name root and the passwor d 12345. You can change the default password later when logging into the device.

3.1 IP Address

T o log on to the device using a web browser, your workstation and the device should both be on the same network segment. The default IP address is 192.168.1.1. You can modify the IP address of your PC by modifying its TCP/IP properties. Follow the steps below:

STEP 1:

Enter the TCP/IP screen and change the IP address to the dom ain of 192.168.1.x/24.

28 July 2004 6212-A2-GB20-20

STEP 2:

Click on OK to submit the settings. Restart the computer when requested.

STEP 3:

Start your Internet browser with the default IP address 192.168.1.1.

3.2 Login Procedure

To log on to the system from the Web browser, follow the steps below:

STEP1:

STEP 2:

STEP 3:

STEP 4:

Start your Internet browser.

Type the IP address for the router in the browser’s location field. F or example, if the

IP address is 192.168.1.1, type http://192.168.1.1

You are prompted to enter your user name and password. The defaul t user name is

root and the default password is 12345. Note if you change the password that the

password is case-sensitive.

After successfully logging in, the main menu appears.

6212-A2-GB20-20 July 2004 29

Chapter 4 Basic Configuration

From the Basic menu bar you can change passwords, configure the WAN/LAN interfaces, set up routing, save settings, reboot the router, and retrieve the factory default settings.

4.1 Software Version Information

Click on Version Information from the Basic menu bar. The screen shows the device name, software version, and build time. The software version and build time on the screen are for reference only . The information displayed on this screen may change when a new software file is upgraded.

30 July 2004 6212-A2-GB20-20

+ 72 hidden pages