Paradyne 6211-I1 User Manual
6211-I1 Router
User’s Guide
Document No. 6211-A2-GB21-30
August 2005
Copyright 2005 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or
by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express
written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.
Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for any help needed. For additional
information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or
Paradyne worldwide office locations, use one of the following methods:
Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at
www.paradyne.com/warranty.)
Telephone: Call our automated system to receive current information by fax or to speak with a company
representative.
— Within the U.S.A., call 1-800-795-8004
— Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them to Technical Publications,
Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the
number and title of this document in your correspondence. Please include your name and phone number if you are
willing to provide additional clarification.
Trademarks
Acculink, ADSL/R, Bitstorm, Comsphere, DSL the Easy Way, ETC, Etherloop, FrameSaver, GranDSLAM, GrandVIEW,
Hotwire, the Hotwire logo, iMarc, Jetstream, MVL, NextEDGE, Net to Net Technologies, OpenLane, Paradyne, the
Paradyne logo, Paradyne Credit Corp., the Paradyne Credit Corp. logo, Performance Wizard, ReachDSL, StormPort,
TruePut are registered trademarks of Paradyne Corporation.
Connect to Success, Hotwire Connected, JetFusion, JetVision, MicroBurst, PacketSurfer, Quick Channel, Reverse
Gateway, Spectrum Manager, and StormTracker are trademarks of Paradyne Corporation.
All other products or services mentioned herein are the trademarks, service marks, registered trademarks, or
registered service marks of their respective owners.
A August 2005 6211-A2-GB21-30
!
Important Safety Instructions
1. Read and follow all warning notices and instructions marked on the product or included in the manual.
2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to
protect it from overheating, these slots and openings must not be blocked or covered.
3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power
cord.
4. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous high
voltage points or other risks. Refer all servicing to qualified service personnel.
5. General purpose cables are used with this product for connection to the network. Special cables, which may be
required by the regulatory inspection authority for the installation site, are the responsibility of the customer. Use a
UL Listed, CSA certified, minimum No. 24 AWG line cord for connection to the Digital Subscriber Line (DSL)
network.
6. When installed in the final configuration, the product must comply with the applicable Safety Standards and
regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory
agencies and inspection authorities to ensure compliance.
7. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If products
installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition. Consult
a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary, implement
corrective action prior to interconnecting the products.
8. Input power to this product must be provided by one of the following: (1) a UL Listed/CSA certified power source
with a Class 2 or Limited Power Source (LPS) output for use in North America, or (2) a certified transformer, with a
Safety Extra Low Voltage (SELV) output having a maximum of 240 VA available, for use in the country of
installation.
9. In addition, since the equipment is to be used with telecommunications circuits, take the following precautions:
— Never install telephone wiring during a lightning storm.
— Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
— Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface.
— Use caution when installing or modifying telephone lines.
— Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of
electric shock from lightning.
— Do not use the telephone to report a gas leak in the vicinity of the leak.
CE Marking
When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be
downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Library → Technical Manuals →
CE Declarations of Conformity.
FCC Part 15 Declaration
An FCC Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com.
Select Support -> Technical Manuals -> Declarations of Conformity.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The authority to operate this equipment is conditioned by the requirement that no modifications will be made to the
equipment unless the changes or modifications are expressly approved by the responsible party.
6211-A2-GB21-30 August 2005 B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Notice to Users of the United States Telephone Network
The following notice applies to versions of the modem that have been FCC Part 68 approved.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for
Terminal Attachment (ACTA). On the bottom side of this equipment is a label that contains, among other information, a
product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the Telephone
Company.
This equipment is intended to connect to the Public Switched Telephone Network through a Universal Service Order
Code (USOC) type RJ11C jack. A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It has been designed to be connected to a compatible
modular jack that is also compliant.
The Ringer Equivalence Number (or REN) is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that
may be connected to a line, as determined by the total RENs, contact the local Telephone Company. The REN for this
product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point. For example, 03 represents a REN of 0.3.
If the modem causes harm to the telephone network, the Telephone Company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the
customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is
necessary.
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the
operation of the equipment. If this happens, the Telephone Company will provide advance notice in order for you to
make necessary modifications to maintain uninterrupted service. If trouble is experienced with the modem, refer to the
repair and warranty information in this document.
If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect
the equipment until the problem is resolved.
The user may make no repairs to the equipment.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service
commission or corporation commission for information.
If the site has specially wired alarm equipment connected to the telephone line, ensure the installation of the modem
does not disable the alarm equipment. If you have questions about what will disable alarm equipment, consult your
Telephone Company or a qualified installer.
C August 2005 6211-A2-GB21-30
Notice to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was
performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It
does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment. The REN
assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may consist of any combination of devices subject
only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
If your equipment is in need of repair, contact your local sales representative, service representative, or distributor
directly.
!
CANADA - EMI NOTICE:
This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du
Canada.
Japan Notices
This is a Class B product based on the standard of the Voluntary Control Council for
Interference from Information Technology Equipment (VCCI). If this is used near a radio or
television receiver in a domestic environment, it may cause radio interference. Install and use
the equipment according to the instruction manual.
6211-A2-GB21-30 August 2005 D
E August 2005 6211-A2-GB21-30
Contents
About This Guide
1 Introduction
Document Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . . v
Document Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Product-Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
2 Hardware Installation and PC Setup
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Connecting the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Installing the USB Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Configuring Your Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Windows XP PCs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Windows 2000 PCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Windows ME PCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Windows 95 and Windows 98 PCs . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Windows NT 4.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Logging in to Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
3 Device Information
Status Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
WAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
LAN Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
WAN Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
ATM Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
ADSL Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
ADSL BER Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
6211-A2-GB21-30 August 2005 i
Contents
Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
4 Quick Setup
Quick Setup with Auto-Connect Enabled . . . . . . . . . . . . . . . . . . . . . . . 4-1
Quick Setup with Auto-Connect Disabled . . . . . . . . . . . . . . . . . . . . . . 4-3
5 Advanced Setup
WAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Local Area Network (LAN) Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
NAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
DMZ Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Firewall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Quality of Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20
Routing – Default Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22
Routing – Static Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
Routing – RIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
DNS Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
Dynamic DNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
ADSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
DSL Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28
Tone Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Port Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30
Add Function – ATM PVC Configuration . . . . . . . . . . . . . . . . . . . . 5-2
Connection Type Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Bridge Service and Quality of Service Screen. . . . . . . . . . . . . . . . 5-4
WAN Setup - Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Remove Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Finish Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Virtual Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
IP Filtering – Outgoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
IP Filtering – Incoming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
Firewall – MAC Filtering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Parental Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
Modulation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
Phone Line Pair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27
Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27
ii August 2005 6211-A2-GB21-30
6 Diagnostics
7 Management
Contents
Testing the DSL Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Saving and Restoring the Configuration . . . . . . . . . . . . . . . . . . . . . . . 7-1
Backing Up Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Restoring Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Restoring Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
View System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Configure System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
SNMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
Internet Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Access Control – Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
Access Control – IP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
Access Control – Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
Update Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
Reboot Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16
A Specifications
Index
6211-A2-GB21-30 August 2005
iii
Contents
iv August 2005 6211-A2-GB21-30
About This Guide
Document Purpose and Intended Audience
This guide contains detailed information about the 6211-I1 router. It is intended for
all users of the router.
Document Summary
Section Description
Chapter 1, Introduction Describes the features of the router.
Chapter 2, Hardware
Installation and PC Setup
Chapter 3, Device Information Explains how to use the web interface to obtain
Chapter 4, Quick Setup Describes the Quick Setup configuration process.
Chapter 5, Advanced Setup Describes configuration of the advanced router
Chapter 6, Diagnostics Describes the test screen.
Chapter 7, Management Describes the management functions of the router,
Appendix A, Specifications Lists the specifications of the router.
Index Lists key terms, concepts, and sections in alphabetical
A master glossary of terms and acronyms used in Paradyne documents is
available online at www.paradyne.com. Select Support → Technical Manuals →
Technical Glossary.
Shows how to connect the router and set up your PC to
manage the router.
statistics and other information about the router.
features.
including backing up and restoring configuration
settings, viewing the system log, configuraing access
control, and upgrading software.
order.
6211-A2-GB21-30 August 2005 v
About This Guide
Product-Related Documents
Complete documentation for Paradyne products is available online at
www.paradyne.com. Select Support → Technical Manuals.
To order a paper copy of a Paradyne document, or to speak with a sales
representative, please call 1-727-530-2000.
vi August 2005 6211-A2-GB21-30
Introduction
Introduction
Features
1
Congratulations on becoming the owner of a 6211 ADSL router.
This User’s Guide will show you how to set up the router, and how to customize its
configuration to get the most out of this product.
The 6211 router has the following features:
Built-in ADSL modem which offers G.Dmt, G.lite, T1.413, ADSL2, Annex L,
and ADSL2+ to meet different linking speeds from your ISP.
10/100BaseT Ethernet port to provide Internet connectivity to all computers on
your LAN via additional Ethernet Switch/HUB.
USB port allows quick installation.
Built-in splitter provides you to connect telephone directly without using extra
splitter (Model 6211-I1-x0x).
Configuration program accessible via a web browser, such as Microsoft
Internet Explorer.
System Requirements
In order to use the 6211 ADSL router for Internet access, you must have the
following:
ADSL service subscription from your ISP
A PC with:
— An Ethernet 10/100BaseT network interface card or USB port
— A processor equivalent to or faster than a Pentium II 133 MHz
— 32 MB RAM or greater
— If USB drivers will be installed, 5 MB free disk space
6211-A2-GB21-30 August 2005 1-1
1. Introduction
Parts List
— Windows 95b, 98, 98SE, 2000, ME, NT, or XP (Note: Windows 95 requires
the installation of the Winsock program, not included. Windows 95 and 98
do not support USB.)
— (Optional) An Ethernet hub or switch, if you wish to connect the router to
several computers on an Ethernet network.
— For system configuration using the supplied web-based program: a web
browser such as Internet Explorer Version 6.0 or later. Netscape is not
supported.
In addition to this document, your 6211 ADSL router should come with the
following:
6211 ADSL router
Power adapter
Ethernet cable (RJ45, straight-through type)
Phone cable (RJ11)
USB cable
USB
LAN
ACTIVITY
STATUS
POWER
04-17511
Figure 1-1. 6211 ADSL Router Package Contents
1-2 August 2005 6211-A2-GB21-30
Front Panel
1. Introduction
The front panel contains LED indicators that show the status of the unit.
POWER
LAN
USB
05-17610
ACTIVITY
STATUS
Figure 1-2. Front Panel LEDs
Table 1-1. Front Panel Label and LEDs
Label Color Function
POWER Green On: Unit is powered on
Off: Unit is powered off
STATUS Green On: ADSL link is established
and active
Flashing: Trying to create an
ADSL connection
Off: No ADSL link
ACTIVITY Green Flashing: ADSL data
transfer
LAN Green On: LAN link is established
Flashing: Data transfer at
LAN connection
Off: No LAN link
USB Green On: USB link is established
Off: No USB link
6211-A2-GB21-30 August 2005
1-3
1. Introduction
Rear Panel
The rear panel contains the ports for the router's data and power connections.
Table 1-2. Rear Panel Labels and Connectors
Label Function
LINE Connects to your ADSL line
PHONE (Model 6211-I1-x0x) Connects to your telephone
USB USB outlet, for PC USB port connection
LAN Connects the CPE to your PC's Ethernet port, or to the
uplink port on your LAN's hub or switch, using the
cable provided
RESET/DEFAULT To reset the router to its default settings
POWER Connects to the supplied power adapter
1-4 August 2005 6211-A2-GB21-30
Hardware Installation and PC Setup
Overview
This chapter provides basic instructions for connecting the router to a computer or
a LAN and to the Internet using DSL. The first part provides instructions to set up
the hardware, and the second part describes how to prepare your PC for use with
the router.
It is assumed that you have already subscribed to DSL service with your Internet
service provider (ISP).
2
Connecting the Hardware
Caution
Shut down your PC and any other equipment before connecting it to the
router.
To connect your router:
Procedure
1. Connect your ADSL line to the port labeled LINE on the rear panel of the
device.
2. For routers with a phone port (model numbers of the form 6211-I1-x0x),
optionally connect your telephone to the port labeled PHONE.
3. Connect your PC or a LAN:
— Use the supplied Ethernet cable to connect your PC directly to the router.
Connect one end of the Ethernet cable to the port labeled LAN on the
router and connect the other end to the Ethernet port of your computer.
— Alternatively, use the supplied USB cable to connect your PC directly to
the router. Connect one end of the USB cable to the port labeled USB on
the router and connect the other end to a free USB port on your PC. Install
the USB drivers as described in the user’s guide on the CD.
6211-A2-GB21-30 August 2005 2-1
2. Hardware Installation and PC Setup
— If your LAN has more than one computer, you can attach one end of an
Ethernet cable to a hub or a switch and the other to the LAN port of the
router. Either a crossover or straight-through Ethernet cable can be used.
4. Connect the AC power adapter to the POWER connector on the back of the
device and plug the adapter into a wall outlet or power strip.
LINE LAN POWERPHONE USB
RESET
DEFAULT
1
2
3
OR
Figure 2-1. Hardware Installation
5. Turn on and boot up your PC and any LAN devices, such as hub or switches,
and any computers connected to them.
6. Verify that the router's LEDs are illuminated as shown in Table 3 1.
4
04-17510
2-2 August 2005 6211-A2-GB21-30
2. Hardware Installation and PC Setup
Table 2-1. LED Indicators
This LED . . . Should be:
POWER Solid green to indicate that the device is turned on. If this light is not
on, check if the power adapter is attached to the router and plugged
into an AC power source.
STATUS Solid green to indicate that the router can communicate with your ISP
via ADSL, or flashing when the router is trying to connect to your ISP.
ACTIVITY Flashing when the device is sending or receiving data over the ADSL
connection.
LAN Solid green to indicate that the device can communicate with your PC
via Ethernet, or flashing when the router is sending or receiving data
over Ethernet.
USB Solid green when connected, flashing when the router is sending or
receiving data.
If the LEDs are illuminated as expected, the router is working properly.
6211-A2-GB21-30 August 2005
2-3
2. Hardware Installation and PC Setup
Installing the USB Driver
The following section applies only if you use the USB connector on the router. If
you connect the USB cable between your PC and the router, Windows detects the
new hardware and the Found New Hardware Wizard appears on your PC monitor.
Follow this procedure:
Procedure
1. Choose "Install from a list or specific location" from the Wizard's menu, then
click on Next.
Figure 2-2. Found New Hardware Wizard
2-4 August 2005 6211-A2-GB21-30
2. Hardware Installation and PC Setup
2. Insert the supplied CD ROM and use Browse to include the CD drive in the
search.
Figure 2-3. Search and Installation Options
3. If the Wizard reports a compatibility issue, select "Continue Anyway".
Installation of the USB driver proceeds.
Figure 2-4. Compatibility Warning
6211-A2-GB21-30 August 2005
2-5
2. Hardware Installation and PC Setup
Figure 2-5. Progress Screen
4. When prompted, click on Finish to close the Wizard.
Figure 2-6. Completion Screen
2-6 August 2005 6211-A2-GB21-30
Configuring Your Computer
Before you can access the router over the LAN or the USB port, you have to
configure your PC's TCP/IP address to be 192.168.1.x (where x is any number
between 3 and 254), with a subnet mask of 255.255.255.0. Your router's default IP
address is 192.168.1.1.
Windows XP PCs
1. In the Windows task bar, click on the Start button, and then click on Control
Panel.
2. Double-click on the Network Connections icon.
3. In the LAN or High-Speed Internet window, right-click on the icon
corresponding to your network interface card (NIC) or USB connection, and
select Properties. (Often this icon is labeled Local Area Connection). The
Local Area Connection dialog box displays with a list of currently installed
network items.
4. Ensure that the check box to the left of the item labeled Internet Protocol
(TCP/IP) is checked, and click on Properties.
2. Hardware Installation and PC Setup
Figure 2-7. Network Connections (Windows XP)
6211-A2-GB21-30 August 2005
2-7
2. Hardware Installation and PC Setup
Figure 2-8. Local Area Connection Properties (Windows XP)
5. In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio
button labeled Use the following IP address. Type an address between
192.168.1.3 and 192.168.1.254 in the IP Address field (192.168.1.20 is shown
here as an example) and 255.255.255.0 in the Subnet Mask field.
Figure 2-9. TCP/IP Properties (Windows XP)
6. Click on OK twice to confirm your changes, and close the Control Panel.
2-8 August 2005 6211-A2-GB21-30
Windows 2000 PCs
2. Hardware Installation and PC Setup
1. In the Windows task bar, click on the Start button, point to Settings, and then
click on Control Panel.
2. Double-click on the Network and Dial-up Connections icon.
3. In the Network and Dial-up Connections window, right-click on the Local Area
Connection icon, and then select Properties.
The Local Area Connection Properties dialog box display a list of currently
installed network components. If the list includes Internet Protocol (TCP/IP),
the protocol has already been enabled; skip to Step 10.
4. If Internet Protocol (TCP/IP) does not appear as an installed component, click
on Install.
5. In the Select Network Component Type dialog box, select Protocol, and then
click on Add.
6. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click
on OK.
You may be prompted to install files from your Windows 2000 installation CD
or other medium. Follow the instructions to install the files.
Windows ME PCs
7. If prompted, click on OK to restart your computer with the new settings.
8. After restarting your PC, double-click on the Network and Dial-up Connections
icon in the Control Panel.
9. In Network and Dial-up Connections window, right-click on the Local Area
Connection icon, and then select Properties.
10. In the Local Area Connection Properties dialog box, select Internet Protocol
(TCP/IP), and then click on Properties.
11. In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio
button labeled Use the following IP address. Type an address between
192.168.1.3 and 192.168.1.254 in the IP Address field and 255.255.255.0 in
the Subnet Mask field.
12. Click on OK twice to confirm and save your changes, and then close the
Control Panel.
1. In the Windows task bar, click on the Start button, point to Settings, and then
click on Control Panel.
2. Double-click on the Network and Dial-up Connections icon.
3. In the Network and Dial-up Connections window, right-click on the Network
icon, and then select Properties.
The Network Properties dialog box displays a list of currently installed network
components. If the list includes Internet Protocol (TCP/IP), the protocol has
already been enabled; skip to Step 11.
6211-A2-GB21-30 August 2005
2-9
2. Hardware Installation and PC Setup
4. If Internet Protocol (TCP/IP) does not appear as an installed component, click
on Add.
5. In the Select Network Component Type dialog box, select Protocol, and then
click on Add.
6. Select Microsoft in the Manufacturers box.
7. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click
on OK.
You may be prompted to install files from your Windows Me installation CD or
other media. Follow the instructions to install the files.
8. If prompted, click on OK to restart your computer with the new settings.
9. After restarting your PC, double-click on the Network and Dial-up Connections
icon in the Control Panel.
10. In Network and Dial-up Connections window, right-click on the Network icon,
and then select Properties.
11. In the Network Properties dialog box, select TCP/IP, and then click on
Properties.
12. In the TCP/IP Settings dialog box, click on the radio button labeled Use the
following IP address. Type an address between 192.168.1.3 and
192.168.1.254 in the IP Address field and 255.255.255.0 in the Subnet Mask
field.
13. Click on OK twice to confirm and save your changes, and then close the
Control Panel.
Windows 95 and Windows 98 PCs
1. In the Windows task bar, click on the Start button, point to Settings, and then
click on Control Panel.
2. Double-click on the Network icon.
The Network dialog box displays a list of currently installed network
components. If the list includes TCP/IP, the protocol has already been
enabled. Skip to step 9.
3. If TCP/IP does not appear as an installed component, click on Add. The Select
Network Component Type dialog box appears.
4. Select Protocol, and then click on Add.
The Select Network Protocol dialog box appears.
5. Click on Microsoft in the Manufacturers list box, and then click on TCP/IP in
the Network Protocols list box.
6. Click on OK to return to the Network dialog box, and then click on OK again.
You may be prompted to install files from your Windows 95/98 installation CD.
Follow the instructions to install the files.
7. Click on OK to restart the PC and complete the TCP/IP installation.
2-10 August 2005 6211-A2-GB21-30
Windows NT 4.0
2. Hardware Installation and PC Setup
8. After restarting your PC, open the Control Panel window, and then click on the
Network icon.
9. Select the network component labeled TCP/IP, and then click on Properties.
If you have multiple TCP/IP listings, select the listing associated with your
network card or adapter.
10. In the TCP/IP Properties dialog box, click on the IP Address tab.
11. Click in the radio button labeled Use the following IP address. Type an address
between 192.168.1.3 and 192.168.1.254 in the IP Address field and
255.255.255.0 in the Subnet Mask field.
12. Click on OK twice to confirm and save your changes. You will be prompted to
restart Windows. Click on Yes.
1. In the Windows NT task bar, click on the Start button, point to Settings, and
then click on Control Panel.
2. In the Control Panel window, double click on the Network icon.
3. In the Network dialog box, click on the Protocols tab.
The Protocols tab displays a list of currently installed network protocols. If the
list includes TCP/IP, the protocol has already been enabled. Skip to Step 9.
4. If TCP/IP does not appear as an installed component, click on Add.
5. In the Select Network Protocol dialog box, select TCP/IP, and then click on
OK.
You may be prompted to install files from your Windows NT installation CD or
other medium. Follow the instructions to install the files.
After all files are installed, a window appears to inform you that a TCP/IP
service called DHCP can be set up to dynamically assign IP information.
6. Click on Yes to continue, and then click on OK, if prompted, to restart your
computer.
7. After restarting your PC, open the Control Panel window, and then double-click
on the Network icon.
8. In the Network dialog box, click on the Protocols tab.
9. In the Protocols tab, select TCP/IP, and then click on Properties.
10. In the Microsoft TCP/IP Properties dialog box, click on the radio button labeled
Use the following IP address. Type an address between 192.168.1.3 and
192.168.1.254 in the IP Address field and 255.255.255.0 in the Subnet Mask
field.
11. Click on OK twice to confirm and save your changes, and then close the
Control Panel.
6211-A2-GB21-30 August 2005
2-11
2. Hardware Installation and PC Setup
Logging in to Your Router
This section shows how to connect to the router's web interface, configure
settings, and observe some statistics of your Internet connection.
1. Open your Web browser, and type the following URL in the address/location
box, and press Enter:
http://192.168.1.1
This is the default IP address for the LAN port on the router.
A login screen appears.
Figure 2-10. Login Screen
If you have problem connecting to the router, verify that your PC is properly
configured within the subnet of the router's default IP address 192.168.1.1.
Setup is described in Configuring Your Computer on page 2-7.
2. Enter your user name and password, and then click on OK to display the home
page of the router's web interface. There are two default user name and
password combinations:
Table 2-2. Default User Names and Passwords
User Name Password Capability
user user Can display device status, but cannot change or save
configuration options.
admin admin Can perform all functions.
You can change the passwords at any time.
The home page is shown in Figure 2-11.
2-12 August 2005 6211-A2-GB21-30
2. Hardware Installation and PC Setup
Figure 2-11. Web Interface Home Page
6211-A2-GB21-30 August 2005
2-13
2. Hardware Installation and PC Setup
2-14 August 2005 6211-A2-GB21-30
Loading...