Page 1
8-Zone Expansion Modules
ZX8
V6.0
Instructions / Instrucciones
PARADOX.COM
Printed in Canada - 05/2014
Figure 1: ZX8 Connections
The 8-zone Expansion Module (ZX8) is an interface between t he control
panels and any hardwired detection devices. The ZX8 conne cts to the
control panel's combus to provide eight additional hardw ired inputs
and one 50mA on-board PGM output.
Specifications
Installation
Connect the module as shown in Figure 1.
Table 1: Jumper Setting
Table 2: Illustration
Digiplex +Digiplex EVO
A “Locate” request coming from the contro l panel can be disabled by pressing the “Disable Locate”.
MG/SP Series
Press the “Disable Locate” for 3 seconds. Fast flash of the green LED occurs. Jumper settings can be changed.
Green “LOC” LED
Digiplex and Digiplex EVO
Remains Illuminated during power up
Flashes fast to indicate it is receiving a “Locate” request from the control panel. To disable a “Locate” request, press the “Disable Locate” switch.
SP Series and MG5050
Flashes fast to indicate a change in jumper setting.
Red “WDG” LED
All panels
Flashes to indicate proper operation
If both “LOC” and the “WDG” LED are flashing alternately, the module is
experiencing a communication failure with the control panel.
Connect the detection devices to the ZX8 input terminals exactly as shown in the appropriate control panel’s Programming Guide.
Digiplex y Digiplex EVO
Z8: Input terminal Z8 can be used as an anti-tamper switch input. Enable
section [001] option [1]
MG/SP Series
Z1: Input terminal Z1 can be used as an anti-tamper switch input. Enable
section [706] option [4] for panel+1, option [5] for panel+9 and option [6] for panel+17
Input voltage: Typically 12 to 16 Vdc
Current cons.: 28mA
Max.# of ZX8: max.3: MG/SP Series
No. of outputs: One 50mA PGM
No. of inputs: 8 inputs
No. of zones: 8 standard zone inputs
Oper. temperature: -20ºC to 50ºC (-4ºF to 122ºF)*
Compatibility: Any Digiplex or Digiplex EVO series control panel
Any SP Series control panel (V2.0 or higher)
MG5000/MG5050 control panels (V2.0 or higher)
WinLoad Software V2.03 or higher
NOTE: For 1728/1738 compatibility, refer to the
SP-ZX8 instructions.
MG5000
(2 on-board zones)
MG5050
(5 on-board zones)
SP4000
(4 on-board zones)
SP5500
(5 on-board zones)
SP6000
(8 on-board zones)
SP65
(9 on-board zones)
SP7000
(16 on-board zones)
No/
ATZ
ZTA
With/
ATZ
ZTA
No/
ATZ
ZTA
With/
ATZ
ZTA
No/
ATZ
ZTA
With/
ATZ
ZTA
No/
ATZ
ZTA
With/
ATZ
ZTA
No/
Sin/Sans
ATZ
ZTA
With/
Con/Avec
ATZ
ZTA
No/
Sin/Sans
ATZ
ZTA
With/
Con/Avec
ATZ
ZTA
No/
Sin/Sans
ATZ
ZTA
With/
Con/Avec
ATZ
ZTA
zones/ zones/ zones/ zones/ zones/ zones/ zones/z
A / Panel+1*
3-10 5-12 6-13 11-18 5-12 9-16 6-13 11-18 9-16 17-24 10-17 19-26 17-24 -
B / Panel+9*
11-18 13-20 14-21 19-26 13-20 17-24 14-21 19-26 17-24 25-32 18-25 27-32 25-32 -
C / Panel+17*
19-26 21-28 22-29 27-32 21-28 25-32 22-29 27-32 25-32 - 26-32 - - -
*Press “Disable Locate” for 3 seconds to change jumper setting
A
B
C
D
External
Anti-Tamper
Switch (N.C.)
ZX8-TI03
Page 2
Table 3: Options
[1] Tam pe r R eco gn it io n OFF† = Disabled ON = Enabled (Z8)
[2] PGM Deactivation OFF† = Deact. Event ON = PGM timer
[3] PGM Normal State OFF† = N.O. ON = N.C.
[4] PGM Base time OFF† = 1 sec. ON = 1 min.
(Default = all inputs @ 600ms)
Even numbered sections represent inpu ts terminals Z1 to Z8. Using [] and [] keys. Select a Base Time value from 000 to 002. Press [ENTER].
000= Input Speed is X by 15 milliseconds.
001= Input Speed is X by 1 second.
002= Input Speed is X by 1 minute.
Odd numbered sections represent inputs Z1 to Z8. Enter a 3-digit decimal time value (000 to 255). Multiply by the Input Speed.
Enter a 3-digit decimal value (001-255). Multiply by the PGM Base Time Selection.
__/__/__ Event Group
__/__/__ Feature Group
__/__/__ Start# Set the range within the Feature Group
__/__/__ End# Set the range within the Feature Group
__/__/__ Event Group
__/__/__ Feature Group
__/__/__ Start# Set the range within the Feature Group
__/__/__ End# Set the range within the Feature Group
Activate PGM for 8 seconds to verify if the PGM is functioning properly.
By default, all options are configured as “0”. This means that all zone inputs will follow the global setting at panel section [3033], options 7 and 8. However, if
you change the value from 1 to 4, the inputs will follow the desired settings as shown below.:
†Default Setting / *Only Event Groups 000 to 055 can be used. See PGM Table in the panel’s Programming Guide.
Programming Method
[1] EOL Zones OFF = No EOL ON = With EOL
[2] Tam pe r R eco gn it io n OFF = Disabled ON = Enabled (Z1)
[3] PGM Follows Global PGM OFF = Disabled ON = Enabled
Enable zone inputs. Options [1] to [8], represent inputs Z1 to Z8.
__/__/__ 000 - 255 sec. 000 = Follow Deactivation Event.
__/__ Event Group [60] T
amper zone opened
[61] Tamper zone closed
__/__ Sub-Group [1] to [8] Zone input Z1 to Z8
__/__ Partition Not Used: Enter [00]
__/__ Event Group [60] Tamper zone opened
[61] Tamper zone closed
__/__ Sub-Group [1] to [8] Zone input Z1 to Z8
__/__ Partition Not Used: Enter [00]
Warranty
For complete warranty information on this product please refer to the Limited Warranty Statement found on the website www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all warranty terms and conditions.
Magellan, Spectra SP, Digiplex and Digiplex EVO are trademarks or registered trademarks of Paradox Security Systems Ltd. or its affiliates in Canada, the United States and/or other countries. For the latest information on products approvals, such as UL and CE, please visit www.paradox.com. © 2010 Paradox Security Systems Ltd. All rights reserved. Specifications
may change without prior notice. One or more of the following US patents may apply: 7046142, 6215399, 6111256, 6104319, 5920259, 5886632, 5721542, 5287111, 5119069, 5077549 and RE39406 and other pending patents may apply. Canadian and international patents may also apply.
Programming Method
1. Hold [0] key+ [INSTALLER CODE]
2. Enter section [953] (DGP-848) [4003] (EVO)
3. Enter module’s 8-digit [SERIAL NUMBER]
4. Enter [SECTION] and turn desired option ON/OFF or enter the required data
Sections
[001]
Options
[002]-[016]
Even Numbered
Input Speed (Base Time Selection)
[003]-[017]
Odd Numbered
Input Speed (Time Value)
[018]
PGM Timer
[019]
[020]
[021]
[022]
Activation Event*
[023]
[024]
[025]
[026]
Deactivation Event*
[030]
PGM Test Mode
[401]
EOL/ATZ Options per Zone Input
Zone Input Option Individual Settings
[402]
Selectable Input Resistor for EOL and Contact
Zone Input Option Individual Settings
1. [ENTER] + [INSTALLER CODE]
2. Enter [SECTION] and turn desired option ON/OFF or enter the required data
[650]
Tamper Recognition
[651]
Zone Assignment
[655]
PGM Timer
[656]
PGM Activation Event
[657]
PGM Deactivation Event
Loading...