Quantum Series
PD60S & PD60SL
Modem Redundancy Switch
OVERVIEW
The Quantum Modem Redundancy Switch
system offers a revolutionary approach to
Modem Redundancy Protection by integrating
the Backup Modem and 1:N Redundancy
Controller into a single unit. The Backup
Modem / Controller becomes a 3RU high 19
inch chassis, which incorporates the traffic and
overhead interface connectors necessary to
support the online Modem group. This low cost
and compact 1:N scheme employs proven
integrated 1:1 Redundancy technology
pioneered by Paradise Datacom.
EASE OF OPERATION
An innovative new menu structure makes
configuration a simple procedure. Advanced
user interfaces support the display of text in
different languages. Unique Web User Interface
offers full remote control and in-depth
performance analysis tools using Internet
Explorer without special Monitor & control
software.
FEATURES
Modular design gives maximum flexibility
Integrated Backup Modem and Redundancy
Controller in 3RU
Low Cost
Scaleable up to 1 for 16 (Traffic protection
only)
Scaleable up to 1 for 8 (Traffic and Overhead
protection)
Backup Modem / Controller can be replaced
without affecting traffic
Supports priority traffic channel protection
Supports mixed traffic interfaces including
Ethernet
Supports Manual and Automatic Redundancy
Protection
Redundant power supplies for maximum
reliability
Web User Interfaces Remote Control via
Ethernet - simple to configure
PD60S Supports an IF Modem group with PD20
and/or PD60 Modems and optional Transponder
Switching
PD60SL supports an L-band Modem group with
PD20L and/or PD60L Modems
Paradise Datacom LLC Paradise Datacom Ltd.
328 Innovation Blvd. 1 Wheaton Road, Witham
State College, PA 16803 USA Essex CM8 3UJ England
Tel: 1 (814) 238-3450 Tel: +44(0) 1376 515636
Fax: 1 (814) 238-3829 Fax: +44(0) 1376 533764
1 OF 4 207822 REV A ECO 15932
www.paradisedata.com
Quantum Series
PD60S & PD60SL Modem Redundancy Switch
Instructions for selection of your Quantum Modem Redundancy Switch Options:
1
Select the Redundancy Switch interface options for
interface positions A, B, C & D in accordance with the traffic
interfaces used on the associated Traffic Modems, and
overhead protection if required. Each Switch interface panel
caters for up to 4 Modems with like physical interfaces.
Rear view of PD60S IF Redundancy Switch
A
C
2
Select whether the system is to be IF (PD60S) or L-band (PD60SL).
3
Select the features needed within the Backup Modem, ensuring
that the Backup Modem includes all the features of every
Traffic Modem within the Redundancy Group.
B
D
Please select your Backup Interface Options to include all modem interfaces within the group.
Interface
Position A
hardware
option
Interface
Position B
hardware
option
Interface
Position C
hardware
option
Interface
Position D
hardware
option
1 Option
Select
1 Option
Select
1 Option
Select
1 Option
Select
4 x LVDS / EIA530 on D25 female supports serial LVDS, RS422, X.21, V.35
4 x G.703 on BNC and RJ45 supports G.703 unbalanced and balanced
4 x HSSI on HD50 50-way SCSI-2 connector
4 x Ethernet on RJ45 supports 10/100BaseT Ethernet
4 x LVDS / EIA530 on D25 female supports serial LVDS, RS422, X.21, V.35
4 x G.703 on BNC and RJ45 supports G.703 unbalanced and balanced
4 x HSSI on HD50 50-way SCSI-2 connector
4 x Ethernet on RJ45 supports 10/100BaseT Ethernet
Blanking Plate (position not used)
4 x LVDS / EIA530 on D25 female supports serial LVDS, RS422, X.21, V.35
4 x G.703 on BNC and RJ45 supports G.703 unbalanced and balanced
4 x HSSI on HD50 50-way SCSI-2 connector
4 x Ethernet on RJ45 supports 10/100BaseT
4 x overhead protection for Modems connected to Interface Position A
Blanking Plate (position not used)
4 x LVDS / EIA530 on D25 female supports serial LVDS, RS422, X.21, V.35
4 x G.703 on BNC and RJ45 supports G.703 unbalanced and balanced
4 x HSSI on HD50 50-way SCSI-2 connector
4 x Ethernet on RJ45 supports 10/100BaseT Ethernet
4 x overhead protection for Modems connected to Interface Position B
S E L E C T Y O U R O P T I O N S H E R E
Blanking Plate (position not used)
2 OF 4 207822 REV A ECO 15932
Quantum Series
PD60S & PD60SL Modem Redundancy Switch
Fully configurable - only pay for what you need!
PD60 Base Switch
Either IF PD60S
or L-band PD60SL
Wideband L-band
Adds Data Rates to 16,896kbps
Adds Data Rates to 25Mbps
Adds Data Rates to 60Mbps
IP Acceleration
Ethernet Brouting
IP Traffic Shaping
Position 2
(must choose 1 option)
hardware option
Position 2
IP Traffic card options
DVB-S2 Modulation & Coding
hardware options
Low Rate TPC
2nd Generation Turbo
10Mbps maximum
subject to prevailing data rate
limits
High Rate TPC
2nd Generation Turbo
All data rates to 20Mbps
subject to prevailing data rate
limits
Sequential FEC
Limited to 2,048kbps maximum
FastLink
Low Latency LDPC
Possible modes
SCPC DVB-S2
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z
z
z
z
z
z
z
z
z
Description
BPSK/QPSK/OQPSK, 4.8kbps to 10Mbps, 1bps variable rate, closed network modem.
Ethernet 10/100BaseT on RJ45 for M&C, unaccelerated Ethernet 10/100BaseT on RJ45 via traffic or overhead (Ethernet Bridging)
Includes: Viterbi FEC, Rates 1/2, 3/4 & 7/8 with k=7.
Intelsat Reed-Solomon Outer Codec to IESS 308
Advanced ESC: Variable rate Async channel for Closed Net plus ESC operation.
AUPC: Automatic Uplink Power Control (operates through ESC channel)
Remote Web Browser based monitoring tools (Spectrum Display, Constellation Monitor and link performance versus time) plus SMTP email client for status notification.
DHCP allowing IP address to be allocated dynamically via external DHCP network server
Ethernet header compression of data rates up to 2Mbps
IEEE 802.1p QoS supporting choice of strict priority queuing or fair weighting queuing, IEEE 802.1q VLAN support.
50kbps to 10Mbps, 1bps variable rate in DVB-S2 mode, requires a DVB-S2 option
z
IF Frequency 50-90 MHz & 100-180MHz in 100Hz steps, Closed Network modem, Closed Network plus ESC modem. (hardware option)
L-band: 950- 1950MHz with 100Hz resolution, includes 4E-8 internal reference (hardware option)
Extends L-band coverage to 950-2050MHz in 100Hz steps - L-band option only
Extends base operation to 16,896kbps
Extends 16,896kbps operation to 25Mbps - requires 16,896kbps option
Extends 25Mbps operation to 60Mbps - requires 16,896kbps & 25Mbps options
TCP/IP Acceleration to 10Mbps on base Ethernet port, subject to prevailing data rate limits - overcomes performance problems associated with TCP over satellite
Ethernet Brouting for Point-to-Multipoint operation when there is a non-satellite return path - can be used with base Ethernet port or IP Traffic card
Supports allocation of CIR and BIR plus priority for IP Streams identified by IP Address, Diffserv Class, IEEE 802.1p priority tag or MPLS EXP field. Available as an option on the base IP port
and the IP Traffic card.
Blank Panel
IP Traffic card providing TCP acceleration to 16,896kbps, subject to prevailing data rate limits, also provides HTTP Acceleration by prefetching webpage inline obj ec ts to reduce webpage
download time
Adds TCP acceleration up to 25Mbps on IP Traffic card, subject to prevailing data rate limits - requires IP Traffic card
Adds TCP acceleration up to 60Mbps on IP Traffic card, subject to prevailing data rate limits - requires IP Traffic card and requires 25Mbps Acceleration option
Adds Robust Header Compression to RFC 3059 (IP/UDP) at throughput rates to 29kpkts/s (1-way), 22kpkts/s (2-way), subject to prevailing data rate limits - requires IP Traffic card
z
Encapsulation of IP packets and Ethernet frames over DVB uses MPE or ULE protocols
Adds Dynamic Routing: supports RIP, OSPF and BGP, plus 64 static routes - requires IP Traffic card
DVB-S2 CCM Tx - includes QPSK, 8PSK & 16APSK for DVB-S2 use only, includes also DVB-S2 LDPC Error Correction for DVB-S2 only. Must specify IP Traffic card if IP Traffic required
z
Includes SmartLink allowing SCPC features to be overlaid on DVB-S2 space segment.
DVB-S2 CCM Rx - includes QPSK, 8PSK & 16APSK for DVB-S2 use only includes also DVB-S2 LDPC Error Correction for DVB-S2 only. Must specify IP Traffic card if IP Traffic required
z
Includes SmartLink allowing SCPC features to be overlaid on DVB-S2 space segment.
Rates 5/16, 21/44, 0.493, 2/3, 3/4, 0.789, 7/8 Paradise (low latency) in BPSK, QPSK, OQPSK
Rate 7/8 in QPSK, OQPSK
Rate 0.93 Paradise in QPSK, OQPSK
Rates 3/4, 7/8, 0.93 Paradise in 8PSK - requires 8PSK option
Rates 3/4, 7/8, 0.93 Paradise in 16QAM - requires 16QAM option
Rates 5/16, 21/44, 0.493, 2/3, 3/4, 0.789, 7/8 Paradise (low latency) in BPSK, QPSK, OQPSK
Rate 7/8 in QPSK, OQPSK
Rate 0.93 Paradise in QPSK, OQPSK
Rates 3/4, 7/8, 0.93 Paradise in 8PSK - requires 8PSK option
Rates 3/4, 7/8, 0.93 Paradise in 16QAM - requires 16QAM option
Rates 1/2, 3/4, 7/8 in BPSK, QPSK, OQPSK
FastLink LDPC up to 1Mbps, supports BPSK and QPSK, also supports 8PSK - requires 8PSK option, FastLink 8QAM - requires FastLink 8QAM option, and 16QAM - requires 16QAM option
(hardware option)
FastLink LDPC extension to 2.5Mbps - requires FastLink LDPC to 1Mbps
FastLink LDPC extension to 5Mbps - requires FastLink LDPC to 1Mbps and extension to 2.5Mbps
FastLink LDPC extension to 10Mbps - requires FastLink LDPC to 1Mbps plus extension to 2.5Mbps and extension to 5Mbps
FastLink LDPC extension to 25Mbps - requires FastLink LDPC to 1Mbps plus extension to 2.5Mbps, extension to 5Mbps and extension to 10Mbps
FastLink LDPC extension to 60Mbps - requires FastLink LDPC to 1Mbps plus extension to 2.5Mbps, extension to 5Mbps, extension to 10Mbps and extension to 25Mbps
Configuration options continue on next page.
3 OF 4 207822 REV A ECO 15932
Quantum Series
PD60S & PD60SL Modem Redundancy Switch
Paired Carrier Operation
Paired Carrier
Disabled
Paired Carrier
Enabled
Can save 50%
on space segment
Paired Carrier
Parameter QUANTUM Series Switch
Paired Carrier Transmit and receive carriers are overlaid on top of
Paired Carrier
data rate options
each other in the same space segment. Echo
cancellation techniques are used in the demodulator
to cancel the transmit carrier and extract the wanted
receive carrier signal .
512kbps, 1024kbps, 2.5Mbps, 5Mbps, 10Mbps,
15Mbps, 20Mbps, 25Mbps, 40Mbps, 50Mbps
and 60Mbps traffic rate
Paired Carrier technology allows both the uplink and
downlink signals to occupy the same space segment.
An adaptive self-interference cancellation technique
removes the uplink signal components generated by
the local terminal from the received signal off satellite,
allowing demodulation of the far end signal.
PAIRED CARRIER MODEM SCHEMATIC
FastLink 8QAM
8PSK
Including TCM
16QAM
IBS / SMS
Audio Channels
Drop / Insert
including Extended D/I
G.703 Clock Extension
Advanced AUX
Custom
EZ BERT - PRBS Tester
OM-73
48V DC Input
Adaptive Signal Predistorter
Tx Only operation
Rx Only operation
Paired Carrier (carrier
re-use) subject to prevailing
modem data rate limits.
Minimum occupied bandwidth limit of 150kHz, and
maximum occupied bandwidth
limit of 36MHz
Possible modes
SCPC DVB-S2
z
z
z
z z
z z
z z
z z
z z
z z
z z
z
z z
z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
z z
Description
FastLink 8QAM requires FastLink LDPC
Rate 2/3 8PSK Pragmatic TCM to IESS 310
8PSK Turbo available - requires 2nd Generation Turbo FEC option
16QAM - requires either 2nd Generation Turbo FEC option or LDPC option
Satellite Framing to IESS 309 with low rate Intelsat ESC (to IESS 403) & High Rate IBS/SMS ESC
P1348 Emulation mode for IBS 64kbps carrier (2xaudio) or 128kbps (2xaudio + 64kbps data) - requires IBS / SMS & IDR options
T1/E1 linear order Drop/Insert, plus independent timeslot re-ordering on Tx & Rx. Signalling (E1 CAS & T1 RBS). Rx Partial Insert for multi-destinational working,
Timeslot ID maintenance for N=1 to 31 with IBS / SMS or Closed Net plus ESC. Drop/Insert can operate with any interface, although G.703 is typically used
(requires G.703 option if used in G.703 mode)
Provides a stable G.703 E1 or T1 reference clock over satellite when traffic is NOT E1 or T1
Variable rate synchronous Aux channel for IBS / SMS - requires IBS / SMS option
IDR 32/64kbps in place of one/both audio ADPCM ESC channels - requires IDR option
Custom RS Outer Codec values of n, k and interleaver depth. Custom IBS / SMS modes, allocation of overhead between ESC and Aux channels in IBS / SMS, custom backward alarms in
IBS / SMS, and Closed Net plus ESC - requires IBS/SMS option. Custom IDR mode - requires IDR option.
Internal Bit Error Rate Tester (BERT) can run through main data channel, or ESC/Aux channels, or output/input via the terrestrial interface
OM-73 Scrambling, symbol mapping and Viterbi compatibility
48V DC Primary power input in place of 100-240V AC input (hardware option)
Use with 16QAM to relax HPA backoff by up to 1.6dB. Compensates for HPA non-linearities in ground segment and/or transponder. Requires 16QAM option.
Transmit functions only
Receive functions only
Paired Carrier Ready, allows carriers to be overlapped thereby reducing the required satellite bandwidth.
(hardware option) - requires additional cumulative software options below depending upon data rate required
Paired Carrier up to 512kbps traffic rate - requires Paired Carrier Ready option
Extends Paired Carrier up to 1024kbps traffic rate - requires 512kbps option
Extends Paired Carrier up to 2.5Mbps traffic rate - requires 1024kbps option
Extends Paired Carrier up to 5Mbps traffic rate - requires 2.5Mbps option
Extends Paired Carrier up to 10Mbps traffic rate - requires 5Mbps option
Extends Paired Carrier up to 15Mbps traffic rate - requires 10Mbps option
Extends Paired Carrier up to 20Mbps traffic rate - requires 15Mbps option
Extends Paired Carrier up to 25Mbps traffic rate - requires 20Mbps option
Extends Paired Carrier up to 40Mbps traffic rate - requires 25Mbps option
Extends Paired Carrier up to 50Mbps traffic rate - requires 40Mbps option
Extends Paired Carrier up to 60Mbps traffic rate - requires 50Mbps option
4 OF 4 207822 REV A ECO 15932
Loading...