EN_Soundtrack_2_Set-Up_Guide.indd 1 13-11-04 5:18 PM
according to mode
to listening experience
* Sonic enhancements
MODE
Music Mode*
Next Track Previous Track
Play/Pause
Mute
Volume Down
Volume Up
Bluetooth
Enable
Source
not apply to this model
Greyed out buttons do
Movie Mode*
Power On/O
power cord
Subwoofer
D
#2 Phillips (not supplied)
Subwoofer feet and screws
with cradle
Subwoofer
wired connection only)
is in horizontal position,
protective end caps
ATTENTION: remove
Soundbar on-wall brackets
using for other sources. See manual for details.
learning codes from remote controls you are
Remote
Your Soundtrack 2 System is capable of
(digital)
Optical cable
C
(analog)
Dual RCA cable
Soundbar feet
Removable grille
‘AAA’ batteries for remote
-+-
+
MODE
B
cord (2 pieces)
Soundbar power
(Adaptor for use when sub
Soundbar
Remote ControlWhat’s in the box . . .
Functions and LED Indication
FUNCTION AND OPERATION
System OFF: Press POWER
System ON: Press POWER
Auxiliary 3.5 mm Stereo Source:
Press SOURCE once
Analog RCA Source: Press SOURCE a second time
Digital Optical Source: Press SOURCE a third time
Bluetooth Wireless Connection: Press SOURCE
a fourth time (see Bluetooth connection for details)
Wireless Soundbar / Subwoofer Connection: Press SYNC.
LED ashes and stops ashing once there is a connection
Volume Up/Down: Press UP ARROW or DOWN ARROW
Max Volume: When volume is set to maximum level
the LED brightness increases and ashes rapidly
Min Volume: When volume is set to minimum level
the LED brightness increases and ashes rapidly
LED
x1
x2
x3
rapid
rapid
rapid
Bluetooth Connection
1. FIRST TIME CONNECTION: To connect a phone/tablet that HAS NEVER
been connected to the Soundtrack 2, press the Enable Bluetooth
button on your remote or press the Source button (multiple times if
necessary) on the top-panel of the soundbar until the soundbar LED
rapidly ashes RED then BLUE ( ). The connection
process will take approximately 1 minute. See Step 2.
PREVIOUSLY CONNECTED: If your phone/tablet HAS previously
been connected to Soundtrack 2, the LED will ash RED then
BLUE ONCE ( ). Select Bluetooth as your playback
option and skip step 2.
2. While the LED on the soundbar alternates between RED and BLUE
( ), enable Bluetooth on your phone/tablet and search for
“Soundtrack 2” on your Bluetooth device list. Select “Soundtrack 2” to
establish a connection. Once a connection is established, the LED
illuminates Solid Blue ( ). Depending on phone/tablet you may
need to change the playback device to “Soundtrack 2” or it may
change automatically.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks
of Dolby Laboratories.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and
any use of such marks by Paradigm Electronics Inc. is under license.
The “aptX® software is copyright CSR plc or its group companies. All rights reserved. The aptX®
mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be
registered in one or more jurisdictions.”
x1 x1
For more information visit paradigm.com/shift
A
The Ocial Sound of YOU
™
™
Set-Up Guide
110413
OPTIONAL: For wall mounting instructions, refer to Owners Manual.
WARNING! THE SET-UP AND SYNCING STEPS MUST BE DONE IN THE FOLLOWING ORDER. DO NOT PLUG IN SUBWOOFER UNTIL STEP 7.
Choose subwoofer orientation Setting up the soundbar
EN_Soundtrack_2_Set-Up_Guide.indd 2 13-11-04 5:18 PM
Horizontal
1
2
When subwoofer is in horizontal
position feet must be attached
for heat dissipation.
#2 Phillips (not supplied)
Vertical
Attaching soundbar feet
1
Lay your soundbar face down on a soft
surface. Insert feet as shown, press rmly
until you hear a 'click'.
Power connection
2
Connect soundbar to wall outlet.
A
Connecting to source
3
NOTE: Choose analog
OR digital connections
3.5-mm to mobile
audio device
(not included)
Analog connection to
TV (use for good audio)
TV
CB
Digital connection to TV
(use for best audio)
If desired, establish Bluetooth connection at this point (see rear for details)
B
C
Power on, then initiate audio
4
Using the Remote or Top Panel Controls, turn Power
ON. Then repeatedly press the Source button until
you hear audio from your device (TV, iPhone, etc).
Top Panel Controls
Wireless
Sync
Source Power Volume
Down
Volume
Up
OR
E
D
O
M
Wireless subwoofer pairing
Wireless setting Syncing Adjust subwoofer loudnessPower connection
5 76 8
DO NOT connect subwoofer
to wall outlet until step 7.
Move switch to ‘wireless’ setting
on subwoofer.
Wireless Range
ATTENTION: From the moment you
press the soundbar’s ‘Sync’ button
you have 30 seconds to connect the
subwoofer to the wall outlet.
Press the Sync button to initiate pairing with
subwoofer. The LED on the soundbar should
ash blue ( ) for 30 seconds. Once a connection
is established the LED switches to solid blue ( ).
Connect subwoofer to wall outlet.
D
ATTENTION: If the soundbar’s
LED ashes red and blue,
pairing has failed. Repeat
the Subwoofer Pairing process.
50’
or 15 Meters
Your subwoofer’s LEVEL knob is set to 12 o’clock to
suit average preferences. If desired, adjust up or
down to match sound level of your speakers.
–
BASS
+
BASS
Loading...