SEISMIC™110
Amplifier
Amplifier Features
Bass Driver
Low-Frequency Extension*
Subwoofer Cut-Off Frequency
Sub/Sat Phase Alignment
Line-Level Input
Line-Level Input Sensitivity
Line-Level Input Impedance
Accessory
(sold sep.)
Height, Width, Depth
(Measurements reflect the highest,
widest and deepest points on the subwoofer
and include non-removable feet)
Weight
(unpacked)
Finishes
High-Current Discrete-Output:
1,700 watts Dynamic Peak / 850 watts RMS Sustained
Auto-On/Off; Trigger-On/Off; soft clipping; electrical shorting
protection; thermal protection
254-mm (10 in) high-excursion mineral-filled co-polymer
polypropylene cone with RCR
™
resonance-control ribbing on
underside; FEA-optimized overmolded, inverted Santoprene
®
surround; 38-mm (1-1/2 in) diameter split voice-coil construction
(60-mm coil lengths); dual Nomex
®
spiders; high-temperature
Apical
™
formers; dual 12-mm-thick top plates; 10-lb (4.5 kg)
triple ceramic (hard ferrite) magnet structure; AVS
™
die-cast
heatsink chassis
18 Hz (DIN)
Variable 35 Hz – 150 Hz; Bypass Option
Variable 0˚ – 180˚
RCA (S/E) Left and Right or Sub-Out / LFE or Balanced XLR. From
Sub-Out / LFE-Out of preamp/processor or other line-level source
100 mV mono
RCA: 10k ohms; XLR: 20k ohms
Paradigm Perfect Bass Kit
™
34.3 cm x 29.8 cm x 32.0 cm
13-1/2 in x 11-3/4 in x 12-9/16 in
16.8 kg / 37 lb each
Satin Black
*DIN 45 500. Indicates -3 dB in a typical listening room.
SPECIFICATIONS
A LIFESTYLE SUB FOR LIFESTYLE SPEAKERS!
Input and Control Facilities
Input Facilities
Low-Level Input – RCA:
Allows connection from the RCA (S/E) Left and Right or
Sub/LFE Outputs of your Preamplifier/Processor or other
suitable low-level source.
Low-Level Input – Balanced XLR:
Allows connection from the Balanced XLR Sub/LFE
Output of your Preamplifier/ Processor or other suitable
low-level source. This input provides the lowest noise
and distortion. It is important for long cable runs where
noise and distortion could degrade performance.
Control Facilities
Auto On/Off:
Eliminates the need for a manually operated power
switch. Turns the subwoofer on when there is an input
signal. If no signal is present, after a period of time it
turns off.
Trigger On/Off:
Allows the subwoofer’s power on/off to be controlled by
components that have a trigger output (preamp/
processor, etc.).
Subwoofer Cut-Off with Bypass Option:
(Continuously variable 35 Hz – 150 Hz.) Controls the
subwoofer’s upper frequency cut-off and can be set to
match the low-frequency roll-off characteristics of your
system’s speakers.
Bypass Option allows you to bypass the subwoofer’s
built-in cut-off control to let your preamp/processor’s or
receiver’s internal bass management system provide
the crossover function.
Subwoofer Level Control:
Balances the subwoofer level with that of the other
speakers in your system.
Phase Alignment:
(Continuously variable 0º – 180º.) Accurately synchronizes
your subwoofer and front speakers through their bass
frequency overlap region.
USB Port / PBK Interface:
Allows for:
– Connection of the Paradigm Perfect Bass Kit digital
room correction system, sold separately
– Potential Future upgrades to software installed in
your subwoofer
The fabulous little Seismic™110 sonic bulldog is
designed to provide the deep bass performance in any
Paradigm Reference Home Theater system and in
particular a Millenia™lifestyle system for a blockbuster
movie night at home!
www.paradigm.com
Paradigm
®
, Paradigm®Reference and all associated patented and proprietary designs and technologies are registered trademarks
of Paradigm Electronics Inc. Copyright © Paradigm Electronics Inc. All rights reserved.
Paradigm reserves the right to change specifications and/or features without notice as design improvements are incorporated.