ParaBody 965101, Serious Steel 965101 Assembly Manual

Serious Steel

965101

FLAT & INCLINE BENCH

.ASSEMBLY INSTRUCTIONS

ParaBody, Incorporated

14150 Sunfish Lake Boulevard

Ramsey, MN 55303

1-800-328-9714

Part# 6653501

Revision: 11/26/96

965101

FLAT & INCLINE BENCH ASSEMBLY PARTS LIST

SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBI,Y

HARDWARE."
ITEM NAME/DESCRIPTION Q’IT

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

1/2 X 9-I/2 I"N BOLT .........................................................................................................

1

1/2 X 6-1/21l"i’4 BOLT .........................................................................................................

1

1/2 X 3 IN BOLT ...............................................................................................................

2

1/2 X 1-1/4 IN BOLT .........................................................................................................

2

3/8 X 1 IN BOLT ...............................................................................................................

6

1/2 IN W~SHER. ................................................................................................................

6

3/8 IN WASHER. ................................................................................................................

6

1/2 IN LOCK NUT .............................................................................................................

3

1/2 IN LOW HEIGHT LOCK NUT ....................................................................................

3

HINGE TAB ......................................................................................................................

2

6-1/8 X 3-7/8 IN U-PIN ......................................................................................................

1

1/2 113 X 5/g IN SPACER. ...................................................................................................

1

SPRING PIN ASSEMBLY .................................................................................................

1

1/2 IN ID CAPNUT ............................................................................................................

1

3 X 2 IN INSERT GUIDE ..................................................................................................

2

3 X 2 IN EI’ID CAP ............................................................................................................

3

7/16 ID X 4 IN VINYL CAP ..............................................................................................

1

WELDMENTS/PARTS:
ITEM NAME/DESCRIPTION

QTY

2.

3.

4.

5.

6.

7.

8.

REAR UPRIGHT WELDMENT ...............................

(6651703) .....................................

1

BENCH FRAME WELDMENT ................................

(6652103) .....................................

1

ADJ SLEEVE WELDM]gNT .....................................

(6~;52803) ...................

: .................

1

BACK PAD ANGLE ’WELDMENT LEFT ...............

(6624202) .....................................

1

BACK PAD ANGLE WELDMENT RIGHT ............

(6624302) .....................................

1

1/2 X 2 X 15-1/2 IN PLATE .......................................

(6(,51602) .....................................

2

SEAT PAD ....................................

.~..~..~.:.~....~....X..~.... (~ ..................................... 1

BACK PAD ...............................................................

(66529XX) .....................................

NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE ~3OLT.

BOLT LENGTH,

BOLT LENGTH RUL]gR:

1/2 I 1/2 [ 1/2 I 1/2 , [ 1/2 [ I/2

3

4 5 6

Part # 6653501

2 Revision: 11/26/96

965101 FLAT & INCLINE BENCH ASSEMBLY INSTRUCTIONS

1.

Slide one (1) 7/]L6 ~ X 4 ~ ~ C~ onto ~e 6-1/8 X 3-7/8 ~ U-P~ ~d proceed to am;emble it
~e BENC~ FR~ ~LD~NT ~ sho~ on ~w~g.

Insert two (2) 3 X 2 INSERT GUIDES into each end of the ADJ SLEEVE WELDMENT as .,;hoxvn
drawing. (NOTE: MAKE SURE THE INSERT GUIDES S NAP INTO THE HOLES OF THE
WELDMENT).. SECURELY assemble the SPRING PIN ASSEMBLY to the ADJ SLEEVE
WELDMENT as shown in (DETAIL A).

Pull back the SPR.ING PIN on the ADJ SLEEVE WELDMENT and slide it over the end of ~ae BENCH
FRAME WELDMENT ,as shown on drawing. Slide WELDMENT up to the f’ast adjustmenl

~.

hole

underneath.

o

Insert three (3)’3 X 2 IN END CAPS into the ends of the REAR UPRIGHT WELDMENT a:; shown
drawing.

SECURELY a.~;semble the REAR UPRIGHT WELDMENT to the BENCH FRAME WELDMENT as
shown on drawing.

Assemble the LEFT and RIGHT BACK PAD ANGLE WELDMENTS, along with two (2) HINGE
TABS to the BENCH FRAME WELDMENT as shown on drawing. (NOTE: TIGHTEN
CONNECTION ENOUGH TO REMOVE TIlE PLAY YET ALLOWING THE PARTS TO
ROTATE FREELY).

7° Assemble t~vo (2) 1/2 X 2 X 15-1/2 IN PLATES to the inside of the LEFT and RIGHT BACK PAD

ANGLE WEL’I)MENTS as shown on drawing. (’NOTE: TIGHTEN CONNECTION ENOUGH
REMOVE "lille PLAY ~rET ALLOWING THE PARTS TO ROTATE FREELY).

Rotate the LEFT and RIGHT BACK PAD ANGLE WELDMENTS up and assemble the 1/2 X 2 X 15­1/2 IN PLATES to the ADJ SLEEVE WELDMENT as shown on drawing. (NOTE: DO NOT OVER

TIGHTEN TI]~S CONNECTION).

Part # 6653501

3

Revision: 11/26/96