ParaBody 832101 User Manual
832101
HOME GYM LEG PRESS OPTION
ASSEMBLY INSTRUCTIONS
SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY
HARDWARE:
ITEM NAME/DESCRIPTION
GRIP, 1 X 8 CLOSED END ............... ~ ...........................................................................................................................2
2.
3.
4.
5.
6.
7.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
PULLEY, 3-I/20D X 3/8 ID X 1 ..................................................
STRIP, NON-SKID 2-i/2 X 5-1/2 .................................................................................................................................. 8
CAP, END2 SQ 10-14 GA ........................................... ; ................................................................................................14
GLIDE, I-I/2 X 3/4 UHMWPE QTY 8 ......................................................................................................................... 1
CAP, cOVER 2 SQ PARABODY LOGO ..................................................................................................................... 2
WHEEL, 20D X 3/8 ID X 1 ........................................................................................................................................... 2
WASHER, FLAT 3/8 ID ......................................... i .......................................................................................................8
WASHER, LOCK 3/8 ID ................................................................................................................................................ 4
NUT, NYLOCK 1/2-13 ..................................... : ............................................................................................................2
NUT, NYLOCK 3/8:16 ........................................................................... .. ......................................................................2
NUT, NYLOCK 112-13 LOW HT .................................................................................................................................. 2
NUT, NYLOCK 3/8-16 LOW HT .................................................................................................................................. l
BOLT, HHG2 3/8-16 X 3 ............................................... ; ...............................................................................................2
BOLT, HHG2 112-13 X 3-I/4 ........................................................................................................................................
BOLT, HHG2 3/8-16 X 2-3/4 ........................................................................................................................................ 2
BOLT, HHG2 1/2-13 X 6-1/2 ...................................................................... ; .................................................................
BOLT, HHG2 3/8-16 X 4-1/2 ....................................................................................................................................... ;1
BOLT,
BEARING, FLANGE 3/4 ID X 10D ............................................................................................................................
SET SCREW, C PT 5/16-18 X 3/8 .................................................................................................................................
BEARING, FLANGE 1/2 ID X 5)80D ............... i .........................................................................................................8
SPACER, 3/8 ID X 5/80D X 3/8 .............................................................................................
ASSY, SPRING PIN 3/8 DIA ........................................................................................................................................ l
SHAFT, .3/4 DIA X 8-1/8 ............................................................................................................................................... 2
HHG2 3/8-16 X 1-I/2 ................................... .....................................................................................................
~ ...............................................................................
QTY
, .....................................
I
2
2
2
4
4
2
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
1iiiiiiii
BOLT LENGTH 1
I
12/08/95
BOLT LENGTH RULER:
1/2 I
1
Attach two (2) 2 SQ. IN, COVER CAPS onto the REAR BASE TUBE as shown on drawing.
2.
3.
4.
Insert all 2 SQ. IN. END CAPS into end of tubes as shown in drawing.
SECURELY assemble the REAR BASE TUBE to the FRAME.
Attach four (4) PARAGLIDE STRIPS to the outside of the ADJUSTMENT TUBE and tour (4) PARAGLIDE STRIPS
the inside of the SEAT WELDMENT as shown in (DETAIL A), and using the following steps:
¯ Thoroughly clean all surfaces where the PARAGLIDE STRIPS are to be attached.
¯ kemove the PARAGLIDE STRIPS from the paper backing and firmly apply them to all shown surfaces.
SECURELY assemble one (1) 3/8 IN. SPRING PIN.ASSEMBLY to the SPRING PIN HOUSING of tl~e SEAT
WELDMENT as shown in (DETAIL B). (IMPORTANT !!! TIGHTEN THE NUT OF THE SPRING
ASSEMBLY SECURELY)
Assemble one (1) ,-I/_ X I IN. PULLEY, t~vo (2) 2 IN. WHEELS, two (2) 3/8 IN. WASHERS, ,nnd two (2)
SPACERS to the ADJUSTMENT TUBE using one (1) 3/8 X 4-1/2 IN. BOLT and one (1) 3/8 IN. LOW HT LOCK
Carefully slide the ADJUSTMENT TUBE into the SEAT WELDMENT and engage SPRING PIN into one of the
adjustment holes.
1/2 I 1/2
I
1/2
I
2 3 4
I , , I . 1 I , , ..I , , ,
1/2
I 1/2 ~
5
I , I ..... , __1
Assemble two (2) LEVER TUBES to the FRAME, using two (2) SHAFTS and secure in place with four (4) SET SCREWS.
(NOTE: A TIGHT FIT IS NECESSARY TO ENSURE PROPER FUNCTION. THE FRAME MAY HAVE TO BE
SLIGHTLY PRIED APART USING THE HANDLE OF A HAMMER OR A SIMILAR INSTRUMENT.) (NOTE:
ONLY TWO LEVER TUBES ARE INCLUDED, THE OTHER TWO LEVER TUBES SHO’WN IN DRAWING ARE
FOR VISUALIZATION ONLY.)
Assemble FOOT PLATE to the LEVER TUBES as shown in drawing. (DO NOT OVER TIGHTEN BOLTS!)
10.
I1.
12.
13.
14.
NOTE: TO ATTACH THE ASSEMBLED 832 LEG PRESS OPTION TO YOUR HOME GYM, SEE INSTRUCTIONS
Carefully attach eight (8) NON-SKID STRIPS to the FOOT PLATE as shown in drawing.
Attach the SEAT WELDMENT to the LEVER TUBES as shown in drawing. (NOTE: DO NOT OVER TIGHTEN
NUTS, THE SEAT WELDMENT AND FOOT PLATE SHOULD BE ABLE TO ROTATE FREELY.)
Assemble the BACK PAD to the SEAT WELDMENT.
Assemble the SEAT PAD and the HANDLE to the SEAT WELDMENT.
Attach two (2) I X 8 IN. GRIPS to the HANDLE as shown in drawing.
INCLUDED IN THE ADAPTER KIT.
12/08/95
2
Loading...