Griddle
G1 Operating Manual
Introduction
Model:
G1
Voltage (V)
220
-
240V 50Hz
Power (W)
3000
Weight (Kg)
23
Cooking Area (mm)
545w x 350d
Dimensions (mm)
555w x 500d x 240h
Thank you for purchasing a Pantheon Catering Equipment product. In this
booklet you will find instructions for safe operation so please read carefully
and retain for future reference.
Warnings and Precautions
The following warnings and precautions are important and must be observed:
• Ensure voltage and frequency power requirements for the griddle match
that of the supply.
• The machine must be earthed when used. There is a danger of electric
shock if it is not earthed.
• In case of emergency, please turn off the power switch and unplug the
machine.
• If the electric wire becomes damaged, a qualified engineer or the
manufacturer must replace it.
Pantheon Catering Equipment is not responsible for any accidents or faults
caused by amendments made to the machine or improper use by the user.
Technical Data
Specifications:
Installation
The installation of the unit must be performed by a qualified technician only.
Place the device on top of a solid, even, safe and stable surface that tolerates
the weight of the unit.
Ensure no flammable products are placed near the unit, as it will get hot.
Position the device appropriately so that the plug is always accessible. Also
ensure the unit isn’t placed close to any water.
Operating Instructions
1. When the griddle is plugged in to the power supply, the green indicator
illuminates.
2. Rotate the temperature controller clockwise.
3. The yellow indicator illuminates and the electric element heats up. When
the temperature reaches the set temperature, the thermostat switches off
the heat and the yellow indicator goes out.
4. When the temperature drops below the temperature that has been set, the
thermostat switches the heat on again.
5. This process repeats in order to maintain the required temperature.
6. Adjust the temperature control dependent on the type of food being
cooked in order to get the best results.
7. When the griddle isn’t being used it is best to turn the machine off at the
mains and ensure the temperature is set on zero.
Maintenance
Cleaning:
Please ensure the unit is turned off and unplugged prior to cleaning. Also
ensure that the unit has sufficiently cooled down if cleaning shortly after use.
Then simply use a damp cloth to wipe all grease and food from the griddle.
Regularly cleaning the griddle will help prolong its life.
Troubleshooting
HL1
－
POWER INDICATOR (GREE
N)
Problem Possible Cause Solution
The girdle is plugged in
and turned on,
however the green
light doesn’t
illuminate
The yellow indicator
stays on and the
temperature cannot
be adjusted.
The yellow indicator is
not illuminated, but
temperature control
functions normally.
1. The fuse has blown
2. The power cord is
not correctly
connected.
1. The connection of
the yellow indicator
is damaged.
2. The thermostat is
broken.
1. The contact for the
indicator is not
functioning.
2. The indicator is
burned out.
1. Replace the fuse
2. Confirm the power
cord is correctly
connected.
1. Check the wiring
for the yellow
indicator
2. Replace the
thermostat
1. Check the
connection.
2. Replace the
indicator.
Circuit Diagram
ST－TEMPERATURE CONTROL HL2－HEATING INDICATOR (YELLOW)
EH－HEATING ELEMENT E－GROUND PROTECTION
Parts Diagram
No. Description
1 Bolt (foot)
2 Rubber (foot)
3 Screw (base)
4 Bottom Plate
5 Nut
6 Outer Plate
7
8 Inner Plate
9 Nut
10 Element Support
11 Element
12 Body Shell
13 Plug & Mains Cable
14 Cable Gland
15 Thermostat
16 Front Cover
17 Bezzel for Temperature Knob
18 Screws
19 Indicator
20 Indicator
21 Control Knob
22 Bottom Panel for Electric Box
23 Screws
24 Drip Tray
25 Drip Tray Housing
Loading...