PANJIT UF808F, UF803F, UF802F, UF806F, UF804F Datasheet
...
UF800F THRU UF808F
ISOLATION ULTRAFAST SWITCHING RECTIFIERVOLTAGE - 50 to 800 Volts CURRENT - 8.0 Amperes
FEATURE
S
Exceeds environmental standards of MIL-S-19500/22
8
Low forward voltage, high current capabilit
y
Ultra Fast recovery times high voltag
e
MECHANICAL DATA
Terminals: Lead solderable per MIL-STD-202, Method 20
8
Mounting Position: An
y
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTIC
S
Single phase, half wave, 60Hz, resistive or inductive load.
UF800FUF801FUF802FUF803FUF804FUF806FUF808
F
UNITS
V
V
Maximum DC Blocking Voltage50100200300400600800VMaximum Average Forward Rectified
¢J
8.0APeak Forward Surge Current, 8.3ms single half sinewave superimposed on rated load(JECEC method)12
5
A
A£gA
n
s
P
F
Typical Junction Resistance (Note 2)
R£KJA1
5
/
W
STG
NOTES
:
r
r
2. Measured at 1 MHz and applied reverse voltage of 4.0 VDC
ITO-220AC
l
Plastic package has Underwriters Laboratory
Flammability Classification 94V-O Utilizing
Flame Retardant Epoxy Molding Compound
l
l
Low power loss, high efficiency
l
l
High surge capacity
l
Case: ITO-220AC full molded plastic package
Polarity: As marked
Weight: 0.08 ounce, 2.24 gram
Ratings at 25 ¢J ambient temperature unless otherwise specified.
For capacitive load, derate current by 20%
TYPE NUMBER
Maximum Recurrent Peak Reverse Voltage 50 100 200 300 400 600 800
Maximum RMS Voltage 35 70 140 210 280 420 560
Current .375”(9.5mm) lead length @ TC=100
Maximum Instantaneous Forward Voltage at 8.0A 1.0 1.3 1.7
Maximum DC Reverse Current @TA=25 ¢J
at Rated DC Blocking Voltage @TA=125 ¢J
10. 0
500
Maximum Reverse Recovery Time(Note 1) 50 100
Typical Junction capacitance (Note 2) 80 50
Operating and Storage Temperature Range TJ,T
-50 to +150
V
£g
¢J
¢J
1. Reverse Recovery Test Conditions: IF=0.5A, IR=1A, I
=0.25A
3. Thermal resistance from junction to ambient and from junction to lead length 0.375"(9.5mm) P.C.B.
mounted
RATING AND CHARACTERISTIC CURVE
S
UF800F THRU UF808F
r
r
1000100 10
1.0 0.1
2
0
4
0
6
0
80 100 120 140
PERCENT OF RATED PEAK REVERSE VOLTAGE
Fig. 2-TYPICAL REVERSE CHARACTERISTIC
S
1
25
75
50
2102001601
20
40
0
804020
10
1.0
0.030.010.4
0.6 0.8
1.0 1.2 1.4 1.8
Fig. 4-TYPICAL JUNCTION CAPACITANCEFig. 5-PEAK FORWARD SURGE CURREN
T
I
C
t
+0.5A
0
-0.25
NOTE:1.Rise Time = 7ns max.
Input Impedance = 1 megohm. 22pF
2.Rise Time = 10ns max.
Source Impedance = 50 Ohms
Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
20
16
12
8
AMPERES
4
0
PEAK FORWARD CURRENT,
0 50
CASE TEMPERATURE,
Fig. 1-TYPICAL FORWARD CURRENT DERATING
CURVE
100
TJ = 125
8.3ms SINGLE HALF SINCEWAVE JEDEC METHOD
100 150
¢J
¢J
-1.0
SET TIME
BASE FOR
50 ns/cm
MICROAMPERES
NSTANTANEOUS REVERSE CURRENT,
1cm
TJ = 125 ¢J
¢J
TJ = 25
AMPERES
25
PEAK FORWARD CURRENT
1
2 5
10
20 50 100
NUMBER OF CYCLES AT 60Hz
Fig. 3-MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
80
APACITANCE, (pF)
UF808F
1
2 5
REVERSE VOLTAGE, VOLTS
UF800F
20 50 100 200 500
UF800F
3.0
UF808F
0.3
0.1
INSTANTANEOUS FORWARD CURRENT, (A)
FORWARD VOLTAGE, VOLTS
Loading...