PANJIT S2J, S2B, S2D, S2G, S2K Datasheet

S2A THRU S2M

FEATURE

S

MECHANICAL DATA

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTIC

S

SYMBOLSS2AS2BS2DS2GS2JS2KS2MUNITS

RRM

Volts

RMS

Volts

D

C

Volts

(AV

)

s

FSM

s

F

R

R

R

J

P

W

STG

SMB/DO-214A

A

SURFACE MOUNT RECTIFIER

VOLTAGE - 50 to 1000 Volts CURRENT - 2.0 Amperes

l

For surface mounted applications

l

High temperature metallurgically bonded-no
compression contacts as found in other
diode-constructed rectifiers

l

Glass passivated junction

l

Built-in strain relief

l

Easy pick and place

l

Plastic package has Underwriters Laboratory
Flammability Classification 94V-O

l

Complete device submersible temperature of
260 ¢J for 10 seconds in solder bath

Case: JEDEC DO-214AA molded plastic
Terminals: Solder plated, solderable per MIL-STD-750,
Method 2026
Polarity: Indicated by cathode band
Standard packaging: 12mm tape (EIA-481)
Weight: 0.003 ounce, 0.093 gram

Ratings at 25¢J ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.

For capacitive load, derate current by 20%.

Maximum Recurrent Peak Reverse Voltage V
Maximum RMS Voltage V
Maximum DC Blocking Voltage V
Maximum Average Forward Rectified Current,
at TL=110

¢J

Peak Forward Surge Current 8.3ms single half sine-

I

I
wave superimposed on rated load(JEDEC method)
Maximum Instantaneous Forward Voltage at 2.0A V
Maximum DC Reverse Current TA=25¢J

At Rated DC Blocking Voltage TA=125

¢J

I

Maximum Reverse Recovery Time (Note 1) T
Typical Junction capacitance (Note 2) C

Typical Thermal Resistance (Note 3)

R£KJL

Operating and Storage Temperature Range TJ,T
NOTES:

1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A

2. Measured at 1 MHz and Applied Vr=4.0 volts

3. 8.0mm2 (.013mm thick) land areas

50 100 200 400 600 800 1000
35 70 140 280 420 560 700
50 100 200 400 600 800 1000

2.0 Amp

60.0 Amp

1.10 Volts

5.0

125

2.5 £g

30.0
16 ¢J

-55 to +150 ¢J

£g A

S

F
/

RATING AND CHARACTERISTIC CURVES

0.3×0.3"(8.0×8.0mm) COPPERPAD AREAS

LEAD TEMPERATURE,

TA = 55

NUMBER OF CYCLES AT 60h

z

PERCENT OF PEAK REVERSE VOLTAGE, %

INSTANTANEOUS FORWARD VOLTAGE, VOLT

S

UNITS MOUNTED O

N

THICK COPPER LAND AREAS

REVERSE VOLTAGE, VOLT

S

1

T

NS

S2A THRU S2M

60

2.4

2.0

1.6

SINGLE PHASE HALF WAVE

1.2

60Hz RESISTIVE OR
INDUCTIVE LOAD P.C.B

0.8

AMPERES

MOUNTED ON

AVERAGE FORWARD

0.4

RECTIFIED CURRENT,

0

0 20

40

60

80 100

120

140

160

50

40

30

20

10

CURRENT, AMPERES

PEAK FORWARD SURGE

0

1.0 2.0 4.0 6.0 10 20 40 60 100

¢J

SINGLE SINE-WAVE
(JEDEC METHOD)

¢J

Fig. 1-FORWARD CURRENT DERATING CURVE Fig. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD

SURGE CURRENT

1,00

10

1

0.1

TJ = 125

¢J

TJ = 75 ¢J

TJ = 25 ¢J

100
50

20
10

5.0

2.0

1.0

0.5

MICROAMPERES

0.01

INSTANTANEOUS REVERSE CURRENT,

0.001
0 20 40

60 80 100 120 140

0.2

0.1
.05

.02
.01

TANTANEOUS FORWARD CURRENT, AMPERES

0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0

Fig. 3-TYPICAL REVERSE CHARACTERISTICS Fig. 4-TYPICAL INSTANTANEOUS FORWARD

CHARACTERISTICS

1000

500

200

20in2 (5.4mm2) + 0.5mil in (0.013mm)

100

50

20
10

5

HERMAL IMPEDANCE(¢J/W)

2
1

0.01

0.1

1 10

100

100
70

10

JUNCTION CAPACITANCE, pF

0.1 1 10 100

REVERSE VOLTAGE, VOLTS

Fig. 5-TRANSIENT THERMAL IMPEDANCE Fig. 6-TYPICAL JUNCTION CAPACITANCE