PANJIT GBU10K, GBU10J, GBU10D, GBU10B, GBU10A Datasheet
DATA SHEET
GBU10A~GBU10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes
GBU
Unit: inch ( mm )
FEATURES
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
• Ideal for printed circuit board
• Reliable low cost construction utilizing molded plastic technique
• Surge overload rating: 200 Amperes peak
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
.100(2.54
.085(2.16)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
GBU10B
50
35
50
100
70
100
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward T
=100°C
C
Rectified Output Current at
I2t Rating for fusing ( t<8.35ms)
Peak Forward Surge Current single sine-wave superimposed on
rated load(JEDEC method)
Maximum Instantaneous Forward Voltage Drop per element at 5.0A
Maximum Reverse Leakage at rated T
CDc Blocking Voltage per element T
=25°
A
=100°C
C
Typical Thermal Resistance per leg(Note 2) RθJA
Typical Thermal Resistance per leg(Note 3) RθJC
Operating and Storage Temperature Range, T
,TSTG
J
GBU10A
)
)
7.40
7.90
(
(
.290
.310
)
)
1.65
2.16
(
(
.065
.085
)
.080(2.03
.065(1.65
.190(4.83
.210(5.33
.880(22.3
.860(21.8
)
)
)
)
GBU10D
200
140
200
)
)
GBU10G
10.0
127
200
1.0
5.0
500
8.6
3.1
-55+150
.160(4.1
.140(3.5
R
)
1.90
(
.075
.050(1.27
.040(1.02
400
280
400
)
2.03
(
.080
)
(
1.52
.060
)
)
)
18.8
(
.740
)
18.0
(
.710
)
)
GBU10J
600
420
600
)
18.3
(
.720
)
17.5
(
.690
.140(3.56
.130(3.30
.040(1.02
.030(0.76
.022(0.56
.018(0.46
GBU10K
800
560
800
)
)
)
)
)
)
UNIT
A
Apk
Vpk
°C / W
°C / W
µA
µA
°C
V
V
V
A
2
sec
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
PAGE . 1DATE : AUG.29.2002
RATING AND CHARACTERISTIC CURVES
HEAT-SINK
MOUNTING, TC
(4X4X0.15) INCH
COPPER PLATE
5.0
AMPERES
60Hz RESISTIVEOR
AVERAGE FORWARD CURRENT
INDUCTIVE LOAD
MOUNTED ON0.5X0.5 INCH
COPPER PCBOARD, TA
0.5"(12.7mm) LEADLENGTH
TEMPERATURE
Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT
MICROAMPERES
INSTANTNEOUS REVERSE CURRENT,
200
160
120
(HALF SINE-WAVE)
FORWARD SURGE CURRENT, AMPERES pk
TJ=25
Pulse Width= 30uS
1% DutyCycle
INSTANTANEOUS FORWARD CURRENT, AMPERES
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
Fig.2 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER ELEMENT
80
40
0
PERCENT OF PEAK REVERSE VOLTAGE
Fig.3 - TYPICAL REVERSE CHARACTERISTICS
TJ=25
f=1MHz
Visg=50mVp-p
CAPACITANCE, pF
REVERSE VOLTAGE, VOLTS
Fig.5 - TYPICAL JUNCTION CAPACITANCE PER ELEMENT
NO.OFCYCLESAT62Hz
Fig.4 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
PAGE . 2DATE : AUG.29.2002
Loading...