PANJIT GBJ6A, GBJ6K, GBJ6J, GBJ6G, GBJ6D Datasheet

Approve Sheet

DATA SHEET

GBJ6A~GBJ6K

GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOL TAGE - 50 to 800 Volts CURRENT - 6.0 Amperes

FEA TURES

• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O

• Ideal for printed circuit board

• Reliable low cost construction utilizing molded plastic technique

• Surge overload rating: 175 Amperes peak

• High temperature soldering guaranteed:

260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension

MECHANICAL DATA

Case: Reliable low cost construction utilizing
molded plastic technique
T erminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.

Weight: 0.15 ounce, 4.0 grams

0.146(3.7)

0.087(2.2

0.070(1.8

0.044(1.1

0.035(0.9)

0.304(7.7)

0.288(7.3)

C 0.118 (3.0)

0.129(3.3)

)
)

)

Part Number: GBJ6A~GBJ6K

)

14.7

(

0.578

)

17.0

(

0.669

0.122(3.1)

)

15.3

(

0.603

)

18.0

(

0.709

Unit: inch ( mm )

0.142(3.6)

GBJ

0.996(25.3)

0.972(24.7)

0.304(7.7)

0.288(7.3)

0.304(7.7)

0.288(7.3)

0.189(4.8

0.173(4.4

0.150(3.8

0.133(3.4

)

9.7

(

0.382

0.115(2.9)

0.098(2.5)

0.032(0.8

0.024(0.6

)

9.3

(

0.366

)

)

)
)

)
)

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.

GBJ6B

50
35
50

100

70

100

Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward T

Rectified Output Current

2

I

t Rating for fusing ( t<8.3ms)

Peak Forward Surge Current single sine-wave superimposed on rated load
(JEDEC method)

Maximum Instantaneous Forward Voltage Drop per element at 6.0A
Maximum Reverse Leakage at rated T

CDc Blocking Voltage per element T
Typical Thermal Resistance per leg(Note 2) RθJA
Typical Thermal Resistance per leg(Note 3) RθJC
Operating and Storage Temperature Range, T

=100°C

C

=25°

A

=100°C

C

,TSTG

J

GBJ6A

GBJ6D

200
140
200

-55 to +150

6.0

127

175

1.0
5

500

8.6

3.1

GBJ6G

400
280
400

GBJ6J

600
420
600

GBJ6K

800
560
800

UNIT

V

V
V

A

2

A

sec

Apk
Vpk

µA
µA

°C / W
°C / W

°C

NOTES:

1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.

2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.

3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.

PAGE . 1

Approve Sheet

Part Number: GBJ6A~GBJ6K

RATING AND CHARACTERISTIC CURVES

6.0

HEAT-SINK
MOUNTING,TC

4.0

2.0

AMPERES

AVERAGE FORWARD CURRENT

(4* 4* 0.15) INCH
COPPER PLATE

MOUNTEDONPCBOARD.
TA 0.5"(12.7mm) LEAD LENGTH
60Hz RESISTIVE OR INDUCTIVE LOAD

0

0 50 100 150

TEMPERATURE C

O

Fig. 1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT

10

O

T =100 C

C

1.0

100

40

20

10

4.0

2.0

1.0

0.4

0.2

INSTANTANEOUS FORWARD CURRENT, AMPERES

0.1

0.7 0.8

0.9

TJ=25OC
Pulse Width=300 S
1% DULY Cycle

1.0

1.1

1.2

1.3 1.4

INSTANTANEOUS FORWARD VOLTAGE, VOLTS

Fig. 2- TYPICAL INSTANTANEOUS FORWARD

CHARACTERISITCS PER ELEMENT

150

120

90

0.1

MICROAMPERES

INSTANTANEOUS REVERSE CURRENT,

0.01
0 20 40 60 80 100 120 140

O

T=25C

A

PERCENT OF PEAK REVERSE VOLTAGE

Fig. 3- TYPICAL REAK REVERSE CHARACTERISTICS

400

100

O

Tj=25 C

50

f=1.0MHz

Vsig=50mVp-p

CAPACITANCE, pF

10

1

5

REVERSE VOLTAGE, VOLTS

Fig. 5- TYPICL JUNCTION CAPACITANCE PER ELEMENT

60

O

T =105 C

A

FPRWARD SURGE CURRENT, AMPERES pk

(HALF SINE-WAVE)

30

0

1

2

6

10 20 40 60 100

NO.OFCYCLESAT62Hz

Fig. 4- MAXIMUM NON-REPETITEVE PEAK

FORWARD SURGE CURRENT

10

50

100

PAGE . 2