PANJIT GBJ10K, GBJ10J, GBJ10G, GBJ10D, GBJ10B Datasheet

DATA SHEET

GBJ10A~GBJ10K

GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER

VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes

FEATURES

• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O

• Ideal for printed circuit board

• Reliable low cost construction utilizing molded plastic technique

• Surge overload rating: 200 Amperes peak

• High temperature soldering guaranteed:

260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension

MECHANICAL DATA

Case: Reliable low cost construction utilizing

molded plastic technique

Terminals: Leads solderable per MIL-STD-202,

Method 208

Mounting position: Any

Mounting torque: 5 in. lb. Max.

Weight: 0.15 ounce, 4.0 grams

C 0.118 (3.0)

0.146(3.7)

0.087(2.2

0.070(1.8

0.044(1.1

0.035(0.9)

0.304(7.7)

0.288(7.3)

0.129(3.3)

)
)

)

GBJ

0.996(25.3)

0.972(24.7)

0.304(7.7)

0.288(7.3)

)

)

15.3

14.7

(

(

0.603

0.578

)

)

17.0

18.0

(

(

0.669

0.709

0.304(7.7)

0.288(7.3)

Unit: inch ( mm )

0.122(3.1)

0.142(3.6)

0.115(2.9)

0.098(2.5)

0.032(0.8

0.024(0.6

0.189(4.8

0.173(4.4

0.150(3.8

0.133(3.4

)

)

9.7

9.3

(

(

0.382

0.366

)

)
)

)
)

)

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.

For Capacitive load derate current by 20%.

Maximum Recurrent Peak Reverse Voltage

Maximum RMS Input Voltage

Maximum DC Blocking Voltage

Maximum Average Forward T

Rectified Output Current T

2

I

t Rating for fusing ( t<8.3ms)

Peak Forward Surge Current single sine-wave superimposed on rated load

(JEDEC method)

Maximum Instantaneous Forward Voltage Drop per element at 5.0A

Maximum Reverse Leakage at rated T

CDc Blocking Voltage per element T

Typical Thermal Resistance per leg(Note 2) RθJA

Typical Thermal Resistance per leg(Note 3) RθJC

Operating and Storage Temperature Range, T

=100°C

C

= 45°C

A

=25°

A

=100°C

C

,TSTG

J

GBJ10A

GBJ10B

50

35

50

100

70

100

GBJ10D

200

140

200

-55 to +150

GBJ10G

10.0

8.0

166

200

1.0

5

500

18.0

3.0

400

280

400

GBJ10J

600

420

600

GBJ10K

800

560

800

UNIT

V

V

V

A

2

A

sec

Apk

Vpk

µA
µA

°C / W

°C / W

°C

NOTES:

1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.

2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.

3. Units Mounted on a 3.0 x 3.0" x 0.11" thick ( 7.5 x 7.5 x 0.3cm) AL plate.

DATE : AUG.29.2002

PAGE . 1

D

GO CU

HEAT-SINK

MOUNTING, TC

(4X4X0.15) INCH

COPPER PLATE

5.0

AMPERES

60Hz RESISTIVEOR

INDUCTIVE LOAD

MOUNTED ON0.5X0.5 INCH

COPPER PCBOARD, TA

0.5"(12.7mm) LEADLENGTH

TEMPERATURE

Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT

MICROAMPERES

INSTANTNEOUS REVERSE CURRENT,

200

160

120

(HALF SINE-WAVE)

FORWARD SURGE CURRENT, AMPERES pk

TJ=25

Pulse Width= 30uS

1% DutyCycle

INSTANTANEOUS FORWARD CURRENT, AMPERES

INSTANTANEOUS FORWARD VOLTAGE, VOLT

Fig.2 - TYPICAL INSTANTANEOUS FORWAR

CHARACTERISTICS PER ELEMENT

80

40

0

PERCENT OF PEAK REVERSE VOLTAGE

Fig.3 - TYPICAL REVERSE CHARACTERISTICS

TJ=25

f=1MHz

Visg = 50m Vp-p

CAPACITANCE, pF

REVERSE VOLTAGE, VOLTS

NO. OF CYCLES AT 62Hz

Fig.4 - MAXIMUM NON-REPETITIVE PEAK

FORWARD SURGE CURRENT

DATE : AUG.29.2002

PAGE . 2