Panduit VS-ACK-CPWR, VS-ACK-EXT, VS-ACK-KEY, VS-ACK-BATTERY User manual

VeriSafe Access

Control Kit

1003190

© Panduit Corp. 2019

Original Instructions

The VeriSafe Access Control Kit, inst alled with the VeriSafe Abse nce of Volta ge Te ster, provide s an added layer

to the equipment.

VS-ACK-CPWR

VS-ACK-EXT

VS-ACK-BATTERY

VS-ACK-KEY

Instruction Manual

Models: VS-ACK-CPWR, VS-ACK-EXT, VS-ACK-KEY & VS-ACK-BATTERY

Rev: 01; 1-2020

of protection by preventing enclo sure doors from being opened until absence o f voltage is confirmed. Before
entering the electrical cabinet, personnel will use the VeriSafe Absence of Volt ag e T este r to test for absence of
voltage. The VeriSafe Access Control Kit will receive a signal from the VeriSafe Absence of Voltage Tester when
the absence of voltage is confirmed. The rotary latch will unlock, releasing the enclosure door and allow access

TO REDUCE THE RISK OF INJURY, USER
MUST READ INSTRUCTION MANUAL

NOTE: In the interest of higher quality and value, Panduit products are
continually being improved and updated. Consequently, pictures may vary
from the enclosed product.

North America Tech Support:

[e-mail]

Tel: [phone]

EU Tech Support :

emeatoolservicecenter

@panduit.com

Tel: [phone]

Fax: [phone]

NOTE: Updates to this Instruction Manual may be available. Check
www.panduit.com for the latest version of this manual.

Asia Pacific Tech Support:

TechSupportAP@ panduit.com

Telephone:

Korea: 02-21827300

www.panduit.com

Singapore: 1-800-Panduit (7263848)

Australia: 1-800-Panduit (7263848)

© Panduit Corp. 2019

Warning: Do not use this product outside of the specified performance and environmental limits.

Failure to comply with these specifications could result in product failure, personal injury, or death.

Standards

Applications

Degree of Protection*

For Flat Surface Mounting in a TYPE (UL, NEMA and CSA) 1, 12, 4, IP65 Enclosure

Environment

Operating Temperature

-25°C to 60°C (-13°F to 140°F)

Storage Temperature

-45°C to 85°C (-50°F to 185°F)

Humidity

5 to 90% non-condensing; Rated 80% at 40°C, decreasing linearly to 50% at 60°C

VS-ACK-BATTERY

Type

Industrial 9V Metal Lithium (qty: 2)

INSTRUCTION MANUAL VeriSafe ACK

Safety Information

This manual contains information and warnings which must be follow ed to ensure safe operation of the Access Control Kit. If the
Access Control Kit is not used as described in this manual, the safety features of the Access Control Kit might be imp aire d. The
Access Control Kit is designed for use with the VeriSafe AVT. Reference the VeriSafe AVT instruction manual for critical safety
information, installation and operating instructions. Failure to comply with the warnings and information in this manual

could result in product failure, electrical shock, severe injury or death.

Warning:

•

Always de-energize power before accessing an electrical enclosure.

•

Always follow safety and lockout/tagout procedures when working on or near electrical systems and equipment.

•

Use of the Access Control Kit does not replace lockout/tagout procedures. The Access Contr ol Kit is intended to be used in
conjuncti on with the VeriSafe AVT and the lockout/tagout processes.

•

Use proper personal protective equipment (PPE) when working around sources of hazardous electrical energy.

•

Do not use this product outside of the specified performance and environmental lim its. Failure to comply with these
specifications could result in product failure, personal injury or death.

•

This product must be installed by a qualified electrical worker familiar with local and national electrical codes.

•

Always comply with local installation codes and standards.

•

The VS-ACK-BATTERY product uses a lithi um battery that is a fire, explosion and s evere bur n hazard. Do not crush, rechar ge,
disassemble or heat above 85° C, incinerate, or expose contents to water.

•

Use only the included Wire Harness or approved replacement harness to connect the Rotary Latch and VeriSafe AVT.

Technical Specifications

RoHS Restriction of hazardous substances

Electrical System For use in 1 and 3-phase AC or DC systems

*Degree of protection specified is related to the Latch Cam only. To meet the TYPE (UL, NEMA and CSA) 1, 12, 4, IP65 requirements, mount on
a flat surface of an enclosure meeting the appropriate TYPE rating. Verify that the Sealing Washer is clean and properly seated onto the Latch
Cam to ensure proper sealing.

Classification Non-Rechargeable
Designation ANSI-1604LC
Operating Temperature -20°C to 60°C (-4°F to 140°F)
Mounting Type DIN Rail or Surface Mount
Estimated Capacity 1 cycle per week for 10 years

1003190 R00 Page: 1 of 7 10-2019

© Panduit Corp. 2019

INSTRUCTION MANUAL VeriSafe ACK

VS-ACK-CPWR Install Instructions

Figure 1 - Componen ts of the VeriSaf e A cces s C ontr ol Kit – Control Power (VS-ACK-CPWR)

Figure 2 – Quick Assembly Guide 1 – Contr ol Powe r (VS-ACK-CPWR)

1003190 R00 Page: 2 of 7 10-2019