Page 1
UNIVERSAL GROUND BAR SYSTEM
UGB2/0-414-6, UGB2/0-414-12, UGB2/0-414-18,
UGB-IN-SO, UGB-B-SO, CLMAR2/0-14-Q
© Panduit Corp. 2011
MOUNT DIRECTLY TO PANEL
#10-32
FLAT HEAD SCREW
36 lbf-in [4 N
.
m]
DRILL
11/ 64
[4.4mm] HOLE
INSTALLATION INSTRUCTIONS
MOUNTING UNIVERSAL GROUND BAR
MOUNT USING BONDING
STAND-0FF UGB-B-SO
#10-32
MOUNTING SCREW
36 lbf-in [4 N
.
m]
DRILL
11/ 64
[4.4mm] HOLE
T-PMPI-301-PC
MOUNT USING
ISOLATION STAND-OFF UGB-IN-SO
#10-32
MOUNTING SCREW
36 lbf-in [4 N
.
m]
DRILL
11/ 64
[4.4mm] HOLE
* ATTACHING “MAIN” EQUIPMENT GROUNDING CONDUCTOR TO UGB
USING ANTI-ROTATIONAL
CONNECTOR**
CLMAR2/0-14-Q
1/4-28
MOUNTING SCREWS
36 lbf-in [4 N
.
m]
CLMAR2/0-14-Q
* “MAIN” EQUIPMENT GROUNDING CONDUCTOR MAXIMUM OF 2/0 AWG COPPER CONDUCTOR
** SEE PAGE 2 FOR CONNECTOR OPTIONS
*** WIRE PORT CANNOT BE USED WHEN CONNECTOR IS MOUNTED ABOVE WIRE PORT
For Technical Support: www.panduit.com/resources/install_maintain.asp
USING 2 HOLE COPPER
COMPRESSION CONNECTOR**, ***
1/4-28
MOUNTING SCREWS
36 lbf-in [4 N
Page 1 of 2
.
m]
*** SEE NOTE
USING 1 HOLE COPPER
COMPRESSION CONNECTOR**
1/4-28
MOUNTING SCREWS
36 lbf-in [4 N
.
m]
Page 2
© Panduit Corp. 2011
INSTALLATION INSTRUCTIONS
ATTACHING WIRES TO “PORT” CONNECTIONS*
* EQUIPMENT GROUNDING CONDUCTOR MAXIMUM #4 AWG COPPER
RING TERMINALS WITH 1/4” STUD HOLE
& MAX. TONGUE WIDTH OF .55” [14.0]
COMPRESSION CONNECTORS
WITH 1/4” STUD HOLE & MAX.
TONGUE WIDTH OF .55” [14.0]
T-PMPI-301-PC
BARE COPPER WIRE FROM
#14 AWG TO #4 AWG
FERRULES FROM
#14 AWG TO #6 AWG
AFFIX INCLUDED GROUNDING STICKER
IN CLOSE PROXIMITY TO GROUND BAR
CONNECTOR OPTIONS FOR BOTH CODE AND FLEX WIRE
2 HOLE COPPER COMPRESSION CONNECTORS**, 1/4” STUD HOLE WITH 5/8” SPACING:
PANDUIT PART SERIES: LCD, LCC, LCC-W, LCDX, LCCF, LCCX
1 HOLE COPPER COMPRESSION CONNECTORS**, 1/4” STUD HOLE:
PANDUIT PART SERIES: LCAS, LCA, LCB, LCB-W, LCAX, LCAF, LCBX
PANDUIT ANTI-ROTATIONAL COPPER MECHANICAL CONNECTOR:
PART # CLMAR2/0-14-Q (#14 AWG-2/0 AWG)
TERMINALS - RING PART SERIES:
PN-R, PN-RX, PNF-R, PV-R, PV-RX, PK-R, PH-R, PN-HDR, PV-HDR, PV-R, PV-RX, P-R, S-R,
PMNF-R, PMV-R
FERRULES TYPE:
FSD, F (12mm PIN LENGTH RECOMMENDED)
TIGHTENING TORQUE: IN-LBS [N.m]
CONDUCTOR
SIZE
14 AWG - 10 AWG 35 [4.0]
8 AWG 40 [4.5]
6 AWG - 4 AWG 50 [5.6]
ATTACHMENT METHOD
BARE WIRE / TERMINAL /
LUG / FERRULE
** 2 HOLE AND 1 HOLE COPPER COMPRESSION CONNECTORS AVAILABLE WITH SHORT, STANDARD, AND LONG BARREL LENGTHS.
BENT TONGUE AND NARROW TONGUE OPTIONS ARE ALSO AVAILABLE.
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 2 of 2
E-mail:
cs@panduit.com
Fax:
(708) 444-6993
REV 00
Loading...