Page 1
Figure A
Figure B
Figure C
PR143N-SACS
Part Number: SACS50-T100
Stackable Cable Spacer
INSTALLATION INSTRUCTIONS
©Panduit Corp. 2013
Installation of B or C Lashed Cable Supports When Used With
Panduit Stackable Cable Spacers
Stackable Spacers
The stackable spacer is designed and constructed so that it can be snapped into another spacer by
hand. Adding a spacer increases the height of the assembly by 1/2 inch (12.7mm). Spacers provide
two different size grooves to accommodate a variety of cable diameters. Stackable spacers are
designed to be used with Dura-Ty Cable Ties or Pan-Steel Metal Locking Ties.
On Cables Larger than 1. 0" Diameter
Determine the required spacing and assemble
the necessary spacers. Position the spacer(s)
between the messenger strand and the cable so
the longer length of the spacer is perpendicular
to the cable and the strand, as shown in figure
A. Next, thread the tip of the Dura-Ty Cable Tie
or Pan-Steel Metal Locking Tie through the slot
provided in the side of the spacer(s) so the head
of the cable tie is on the top, adjacent to the
strand. Finish the installation by threading the tip
of the cable tie through the head by hand and
tension with the appropriate installation tool.
On Cables Smaller than 1. 0" Diameter
Position the spacer(s) between the strand and the
cable so the longer length of the spacer is parallel
to the cable and the strand, as shown in figure B.
Follow the same steps outlined for larger cable
diameters.
Spacing Two Cables Apart
Position spacer as shown in figure C and use
either a B or C lashed cable support, as outlined,
for attaching a cable to a strand. Can be used for
either aerial or underground applications.
E-mail:
Phone:
866-405-6654
techsupport@panduit.com
Page 1 of 1 Rev 03
www.panduit.com
and Technical Support:
For instructions in Local Languages
www.panduit.com/resources/install_maintain.asp
PR143N-SACS
Part Number: SACS50-T100
Stackable Cable Spacer
INSTALLATION INSTRUCTIONS
©Panduit Corp. 2013
Installation of B or C Lashed Cable Supports When Used With
Panduit Stackable Cable Spacers
Stackable Spacers
The stackable spacer is designed and constructed so that it can be snapped into another spacer by
hand. Adding a spacer increases the height of the assembly by 1/2 inch (12.7mm). Spacers provide
two different size grooves to accommodate a variety of cable diameters. Stackable spacers are
designed to be used with Dura-Ty Cable Ties or Pan-Steel Metal Locking Ties.
Figure A
On Cables Larger than 1. 0" Diameter
Determine the required spacing and assemble
the necessary spacers. Position the spacer(s)
between the messenger strand and the cable so
the longer length of the spacer is perpendicular
to the cable and the strand, as shown in figure
A. Next, thread the tip of the Dura-Ty Cable Tie
or Pan-Steel Metal Locking Tie through the slot
provided in the side of the spacer(s) so the head
of the cable tie is on the top, adjacent to the
strand. Finish the installation by threading the tip
of the cable tie through the head by hand and
tension with the appropriate installation tool.
Figure B
On Cables Smaller than 1. 0" Diameter
Position the spacer(s) between the strand and the
cable so the longer length of the spacer is parallel
to the cable and the strand, as shown in figure B.
Follow the same steps outlined for larger cable
diameters.
Spacing Two Cables Apart
Position spacer as shown in figure C and use
Figure C
either a B or C lashed cable support, as outlined,
for attaching a cable to a strand. Can be used for
either aerial or underground applications.
E-mail:
Phone:
866-405-6654
techsupport@panduit.com
Page 1 of 1 Rev 03
www.panduit.com
and Technical Support:
For instructions in Local Languages
www.panduit.com/resources/install_maintain.asp
Loading...