Page 1
© Panduit Corp. 2013
NOTE - Some views in this document may vary
slightly from your actual cabinet configuration.
NET-A
(S**SHD* - Single Hinge Door Installation
CCESS
INSTRUCTIONS CM618A
S-Type Server Cabinets
)
Tool List:
-8mm socket wrench
-T30 Torx bit
-T25 Torx bit
-2.5mm Allen Key
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Page 1 of 4
Page 2
INSTRUCTIONS CM618A
Single Hinge Door (Bracket Installation)
• VIEW 1 Install Top Hinge Bracket on cabinet frame (remove and re-install top hinge screw, if necessary)
• VIEW 2 Install Door catch on cabinet frame*
• VIEW 3 Install Bottom Hinge Bracket and Hinge Pin on cabinet frame
[2] M4 Flat Head Screws
(use 2.5mm Allen Key)
VIEW 1
[2] M5 or M6 Round Head Screws
(use T25 Torx Bit)
Top Hinge Bracket
*NOTE - Hardware kit includes [2] M5 Torx screws and
[2] M6 Torx screws for Door Catch installation. Use M6
screws if M5 screws do not hold Door Catch tight
against cabinet frame. Holes on newer cabinet frames
are designed to accept M6 screws.
VIEW 2
VIEW 3
M6 Torx Screw
(use T30 Torx bit)
Door Catch
Bottom Hinge Pin
Bottom Hinge Bracket
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 4
Page 3
INSTRUCTIONS CM618A
Single Hinge Door (Installation and Removal)
• VIEW 2 Lift bottom of door onto Bottom Hinge Pin
• VIEW 1 Pull down Compression Sleeve at top door hinge
• VIEW 1 Push Single Hinge Door towards cabinet so that Top Hinge Screw fits through cutout of door
• VIEW 1 Release Compression Sleeve
• REVERSE STEPS to remove Single Hinge Door
Top Hinge Screw
Compression Sleeve (Pull down)
VIEW 1
VIEW 2
VIEW 3
Bottom Hinge Pin
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 4
Page 4
INSTRUCTIONS CM618A
Single Hinge Door (Door Handle Direction Reversal)
• VIEW 1, 2 Remove Top and Bottom Hinge Brackets from current location (remove top hinge screw, if necessary)
• VIEW 1, 2 Install Top and Bottom Hinge Brackets on opposite side of cabinet (re-install top hinge screw, if necessary)
• VIEW 3 Move Door catch to opposite side of cabinet frame
Door Handle Reversal (Lay door on a flat surface) - VIEW 4, 5
• Remove Door Handle Backing Plate and rotate position of Door Handle 180º
• Loosen Cam Screw to reposition Door Cam and Cam Stop to outside of door. Tighten Cam Screw
• With Door Handle repositioned, secure Door Handle Backing Plate to Door Handle
• Remove PANDUIT label and re-attach in correct orientation near top of door
• Reinstall Single Hinge Door per instructions on Page 3
VIEW 1
VIEW 2
VIEW 3
[2] M4 Screws
(use 2.5mm Allen Key)
[2] Hex Nuts
(use 8mm socket wrench)
Top Hinge Bracket
M6 Torx Screw
(use T30 Torx bit)
Bottom Hinge Bracket
Door Cam
(reposition to
outside edge
of door)
Door Handle
(rotate 180º)
Door
Handle
Backing
Plate
Door Catch
VIEW 5
PANDUIT Label
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 4 of 4
VIEW 4
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...