Panduit S7222BDHRSP Installation Manual

V00029EG/01

STOP

READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE

REMOVING CABINET FROM SKID

NET-A

-Phillips screwdriver

-Flatblade screwdriver

-22mm socket wrench

-15mm socket wrench

-13mm socket wrench

-8mm socket wrench

CCESS

S-Type Dynamic Server

TOOL LIST

-7mm socket wrench

-T30 Torx bit

-T25 Torx bit

-6mm Allen key

-2.5mm Allen key

-Wire cutter

© Panduit Corp. 2015

NET-A

(Server Configurations

CCESS

INSTRUCTIONS V00029EG/01

S-Type Dynamic Server Cabinets

)

NOTE - Some views in this document may vary
slightly from your actual cabinet configuration.

Front View

Rear View

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 1 of 16

INSTRUCTIONS V00029EG/01

Table of Contents - Net-Access S-Type Server Cabinets

General Cabinet Operation Page

Packaging Material Removal……………………………………………...…………... 3

Cabinet Removal…………...……………………………………………...…………... 4

Leveling……………………………………………………………………………...... 5

Mounting……………………………………………………………………………..... 6

Ganging………………………………………………………………………………... 7-8

Grounding……………………………………………...…………................................ 9

Overhead Cable Openings…………………………………………………………...... 10

Cable Management Fingers Installation (SN15F, SN25F)………………………….... 11

Single Hinge Door (Removal and Installation)……………………………………...... 12

Rear Split Doors (Removal and Installation)…………………………………….........

Side Panels (Removal/Installation and Adjustment - optional)………………..............

Cabinet Sealing…………………………………….………………………………...... 15

Front and Back Floor Seals (for vertical exhaust ducts)……………………………….

13

14

16

Note: The maximum static weight load of the cabinet is 3000 lbs. [1361 kg]. The maximum
weight load when the cabinet is rolling on casters is 2500 lbs. [1134 kg]. The weight load should
be evenly distributed across the height of the cabinet, with the heaviest components mounted at
the bottom of the cabinet.

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 2 of 16

INSTRUCTIONS V00029EG/01

Packaging Material Removal

Before removal of packaging material:
Check tip indicator on the outside of cabinet to ensure cabinet was shipped in the upright position. If tip indicator shows improper handling,
inspect cabinet for damage before accepting cabinet.
Before handling cabinet:
Small glide strips could be installed at various locations around the cabinet to protect the cabinet’s finish during shipping. These strips are
to be removed prior to handling of cabinet.

“Shipping Hold Down Bracket”

• Remove all stretch wrap and protective cardboard from outside of cabinet

• Remove all Shipping Brackets (if necessary)

IMPORTANT:
Leveling legs must be fully retracted before the cabinet is moved into place. Sliding cabinet on leveling legs may
result in damage to the leveling legs. (Leveling legs ship in retracted position)

Cut stretch wrap/tape and remove cardboard

3/8” bolt (8)
(Use 15mm socket wrench)

Front Door

[2] M14 Hex Nuts
(use 22mm socket wrench)

Front Door
Shipping Bracket

Bracket

3/8 lock washer (4)

3/8 flat washer(4)

(6)
M10 bolt
(Use 15mm
socket wrench)

Repeat steps on rear of cabinet

Note: Doors, Side panels, and other components are removed for clarity.

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 3 of 16

INSTRUCTIONS V00029EG/01

© Panduit Corp. 2015

Ramp Installation/ Cabinet Removal from pallet.

Insert ramp flange into slots located at the rear of the pallet, as shown. Roll off cabinet in direction stated on pallet. NOTE: Removal of
cabinet should be performed with a minimum of three persons, one at each side of the cabinet and one in back of the cabinet. Never
stand in front of the cabinet while being rolled off the pallet, as shown below.

Ramp

CAUTION: Shipping Brackets must be completely
removed before rolling cabinet off of pallet. See page 2
for Shipping Bracket removal instructions.

Slots in pallet

Front of
cabinet

Rear of
cabinet

Note: Roll off direction

IMPORTANT: Do not
stand here while cabinet
is being rolled off the
pallet.

Off ramp only

CAUTION: Minimum of
three persons for safe
cabinet removal.
Ramp is for removing
cabinet from the pallet
only.

Doors must be
closed or removed
prior to removal of
cabinet.

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 4 of 16

INSTRUCTIONS V00029EG/01

Leveling

• Ensure that [4] Leveling Legs are fully retracted

• Slide Cabinet into final position

• Lower the [4] Leveling Legs until the cabinet weight is fully supported

• Adjust the [4] Leveling Legs so that the cabinet is level front-to-back and side-to-side

• Note- If equipment is installed the cabinet can be leveled from the top.

Front-to-Back Cabinet Leveling

[4] Leveling Legs
(use 6mm Allen Key)

Side-to-Side Cabinet Leveling

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 5 of 16

INSTRUCTIONS V00029EG/01

Floor Mounting

• Ensure that [4] leveling legs are fully retracted

• If necessary, secure [2] “Hold Down Brackets” at front and rear of cabinet

• See Floor Mounting View below for floor mounting dimensions

• Attach the anchors to the floor with appropriate hardware for your type of floor

[2] Shipping
Hold Down
Brackets

Floor Mounting View

[6] M10 Hex Head Screws
(use 15mm socket wrench)

DIM A:

-1070mm deep cabinets: 699mm [27.52”]

-1200mm deep cabinets: 1265mm [33.51”]

DIM B:

-600mm wide cabinets: 190mm [7.52”]

-700mm wide cabinets: 240mm [9.48”]

-800mm wide cabinets: 299mm [11.46”]

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 6 of 16

INSTRUCTIONS V00029EG/01

Ganging (front of cabinet)

• Ensure cabinets are level

• Secure ganging brackets to cabinets at [2] front locations shown below

• Do not use ganging brackets to cinch cabinets together

IMPORTANT:
Ensure cabinets are level by following the guidelines on page 5. Leveling the cabinet prior to
ganging is important to ensure proper door operation.

[2] Front Ganging
Brackets

[4] M6 Torx Screws
(use T25 Torx bit)

FRONT OF CABINETS

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 7 of 16

INSTRUCTIONS V00029EG/01

Ganging (rear of cabinet)

• Ensure cabinets are level

• Secure ganging brackets to cabinets at [2] rear locations shown below

• Do not use ganging brackets to cinch cabinets together

IMPORTANT:
Ensure cabinets are level by following the guidelines on page 5. Leveling the cabinet prior to
ganging is important to ensure proper door operation.

[2] Rear Ganging
Brackets

[4] M6 Torx Screws
(use T25 Torx bit)

REAR OF CABINETS

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 8 of 16

INSTRUCTIONS V00029EG/01

Grounding

• Attach grounding lug or grounding bar at any of the [6] location(s) shown below

• Grounding location is indicated by universal ground symbol

• Use M5 bonding screw

[6] Grounding Lug Locations
(Front and Rear of Beams)

Note: top cap removed for clarity.

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 9 of 16

INSTRUCTIONS V00029EG/01

Overhead Cable Openings

• Remove bezel insert to allow for overhead cable entry.

• Remove (8) M5 screws to open 6” x 6” cut-outs, Using T25 torx bit.

• Install M10 threaded rod into [6] tapped holes, if desired for overhead pathway product.

• [2] 152.4mm x 152.4mm [6” x 6”] openings can be used to route power overhead.

• PANDUIT

C

OOL BOOT

TM

products can be used to seal around cables/fiber to prevent hot air recirculation.

Removable Insert

Overhead Cable
Opening Bezel

M5 Screws (8)

Bezel

OPTIONAL

[6] M10 Threaded Holes

[2] 152.4mm x 152.4mm Openings
[6” x 6”]

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 10 of 16

INSTRUCTIONS V00029EG/01

Cable Management Fingers (SN15F, SN25F)

• Insert tabs of cable management finger into mounting slots of cabinet post

• Slide cable management finger inward to lock into place

Cable Managment Finger

-Insert tabs into cabinet post

-Slide inward to lock in place

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 11 of 16

INSTRUCTIONS V00029EG/01

Single Hinge Door (Removal and Installation)

• VIEW 1 Pull down compression sleeve at top door hinge

• VIEW 1 Pull single hinge door away from cabinet so that top hinge screw fits through cutout of door

• VIEW 2 Lift bottom of door off bottom hinge pin

• REVERSE STEPS to install single hinge door

Top Hinge Screw

Compression Sleeve (Pull down)

VIEW 1

VIEW 2

Bottom Hinge Pin

VIEW 3

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 12 of 16

INSTRUCTIONS V00029EG/01

Rear Split Doors (Removal and Installation)

• Open rear split doors to approximately 90º

• Lift rear split doors up pull doors away from cabinet frame

• REVERSE STEPS to install rear split doors

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 13 of 16

INSTRUCTIONS V00029EG/01

Side Panels (Removal/Installation and Adjustment - optional)

• Engage lower tabs of side panel into frame. As shown in Detail View.

• Pivot upper portion of side panel towards the cabinet until horizontal slide latches engage.

• To remove, pull horizontal side latches inward to disengage and remove side panel.

Detail View

Some objects have been removed for clarity.

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 14 of 16

INSTRUCTIONS V00029EG/01

Cabinet Sealing

Install [6] latch plugs [3 upper, and 3 lower] into the door latch cut-outs to the front side of the cabinet only.
Install [2] foam seals to the upper and lower frame. Seal should be pressed up against the equipment rails,
behind the latch plugs.

[3] Latch Plugs

Foam Seal

Foam Seal

[3] Latch Plugs

For Technical Support: http://www.panduit.com/wcs/Satellite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

Page 15 of 16

INSTRUCTIONS V00029EG/01

Front and Rear Floor Seal Installation (Vertical Exhaust Duct ONLY)

• Install floor seal to front or rear of cabinet frame using (2) M10x20mm Bolts. (Flange on floor seal will face outward away from the cab­inet.)

[2] M10x20mm Bolts
(use 15mm socket wrench)

Floor Seal

For Instructions in Local Languages

and Technical Support:

For Technical Support: http://www.panduit.com/wcs/Satel-

lite?pagename=PG_Wrapper&friendlyurl=/en/support/contact-us

www.panduit.com

Page 16 of 16

E-mail:

[e-mail]

Phone:

[phone]