Panduit S6522BA Installation Manual

For more information about Cisco Compatible Solutions visit
https://marketplace.cisco.com/catalog and search Panduit.

Cabinet Systems

Energy Efficient Data

Center Cabinet and

Containment Systems

Using the Panduit Energy
Efficient Data Center Cabinet
System, you can greatly
improve the energy efficiency
of your data center while
confidently increasing
your kW per cabinet density
to increase utilization of your
data center space.

Factors Effecting Efficiency

• Inlet temperatures

• ∆T across heat exchanger

• Capacity utilization

Efficiency Influencers

• Inlet temperatures

• Set points

• Hot air/cold air leakage and recirculation

• Server/CRAH fan speeds

• kW per cabinet density

Enabling Improved Efficiency

• Seal every gap for complete separation
of cooling and exhaust air

• Direct cold air to where it needs to go

• Contain cooling and exhaust air for
maximum cooling capacity efciency

• Monitor to maintain operational and
energy efciency

Reduce Operational Costs, Improve
Capacity Utilization, and Lower
Power Usage Effectiveness (PUE)*

Driven by explosive data processing growth, Data Center Managers face multiple, competing

demands: reducing operational costs, improving energy efciency, and optimizing available

capacity, while sustaining a low total cost of ownership.

To meet these demands while minimizing the risk to service levels, the available data center

space is often underutilized while being overprovisioned with excess power and cooling capacity

regardless of actual IT equipment and space utilization. Today, a typical data center consumes

about 3-5kW per cabinet due to power and cooling concerns, while the available cabinet space

can accommodate 15kW or more per cabinet if managed effectively.

As energy and construction costs continue to rise, over-provisioning and under-utilization are no

longer sustainable. Energy costs related to cooling account for approximately 37% of the overall

data center power consumption

Air

Movement

12%

Cooling

25%

1

and are one of the fastest rising data center operational costs2.

Electricity

Transformer

UPS 10%

Lighting

Etc.,

3%

IT

Equipment

50%

2

visit www.panduit.com/Cabinets

Average data center energy usage allocation

*Power Usage Effectiveness – a metric used to measure how effectively input power is used. It is expressed as a ratio of
power available to power used.
1 Average Data Center Energy Usage Allocation , Lawrence Berkeley National Laboratory 2007
2 451 Research has published 'Highly Energy-Efcient Datacenters in Practice,' October 2012

1

Power and cooling capacity remain the top targets for efciency improvement and optimization of

cooling capacity is often the simplest way for data center operators to realize short term savings

and directly impact PUE

Panduit Labs research conrms that raising the supply air temperature in a data center is one of

the most effective means to reduce energy consumption. In addition, higher return temperatures

enable a higher CRAH ∆T across the heat exchangers allowing the cooling system to operate

more efciently.

A key way to realize this energy efciency potential and enable maximum capacity utilization is to

eliminate the mixing of cold and hot air within the cabinet and at the room level delivering higher

return air temperatures to the cooling system and allowing higher room set points.

3

.

1°C rise in chiller water temperature translates into

3-4% cooling system energy savings4.

3 How To Measure Energy Consumption In Your Data Center, Gartner Core RAS Research Note G00205428, 8 September 2010
4 Design Considerations for Datacom Equipment Centers ASHRAE 2005, ISBN 1-931862-94-X. Page 138

visit www.panduit.com/Cabinets

3

Complete Hot Air/Cold Air Separation is Critical

$0

$20,000

$40,000

$60,000

$80,000

$100,000

$120,000

Leading Server

Cabinet Competitor

Panduit

Leading Network

Cabinet Competitor

15kW 20kW 25kW 30kW 33kW

to Energy Efficiency and Capacity Utilization

Panduit’s Energy Efcient Data Center Cabinet System offers containment, in-cabinet ducting, and improved sealing that optimizes air separation and provide

superior energy savings compared to competitive offerings.

Optimized energy efciency and capacity utilization begin with improved sealing. Even small air leaks within a cabinet will impact data center energy efciency,

regardless of the heat load. Leaks allow hot air recirculation forcing IT equipment inlet fans to work harder and consume more energy, limiting per cabinet power

utilization. Panduit

The graphics below illustrate the impact these leaks have on inlet temperatures. By preventing hot air recirculation, a more consistent inlet temperature gradient

can be realized across the entire front of the cabinet allowing the data center set point to be raised. This results in reduced cooling expense leading to the ability

to increase density power usage per cabinet, and increase available capacity.

®

Net-Access™ Cabinets reduce the air leakage typical in competitive cabinets by as much as 80%.

Improved sealing coupled with containment leads to a $500 annual savings in cooling costs

per cabinet for high density applications at $ .10 per kWh at 15kW per cabinet7.

Inlet Air Temperature Gradients at

Front of Cabinets Comparison

15kW 20kW 25kW 30kW 33kW

7

Impact of Net-Access™ Cabinet with
Net-Contain™ Containment System on
Cooling Energy Costs vs. Competition

7

Panduit® Net-Access™ Cabinets

Annual Cooling Energy Costs

Leading Server Cabinet Competitor

Power per Cabinet

Leading Network Cabinet Competitor

With improved cabinet sealing, in-cabinet ducting, containment, and monitoring, the results show you can significantly
increase energy efficiency by raising the set point temperature in the entire data center.

Scan to learn how Panduit delivered

a 27% energy savings with Energy

Efficient Cabinets and Containment.

4

visit www.panduit.com/Cabinets

7 Maximizing Cooling Energy Efciency with Effective Cabinet Sealing, Panduit White Paper RKAT01-WW-ENG, March 2013

Increase Density to Optimize Data Center Capacity

Panduit Net-Access™ PDUs, integrated into thermally optimized Net-Access™ Cabinets, enable data center managers to realize higher capacity utilization and
reduced OpEx and CapEx costs.

Typical cabinets are loaded to 5 to 7kW on average, which is often far less than the physical space available within the cabinet resulting in overprovisioning or
the need to build expensive new whitespace.

15kW

Gartner estimates that data center floor

space costs $4,900 per cabinet annually

in CapEx and OpEx (excluding power

and cooling) regardless of

capacity utilization.*

Impact of Increasing Density

kW

kW

5

5

kW

kW

5kW5

5

5kW5

5

kW

kW

5

kW

100 kW

5

kW

$98,000

kW

kW

5

5

kW

kW

5kW5

5

5kW5

5

kW

kW

5

kW

5

kW

5-7kW

15

kW

15

kW

15

kW

15

kW

$4,900 per Cabinet Space

15kW15

kW

100 kW

15

kW

$34,300

Typical Density

High Density

Increasing the density of a 100kW data center can reduce

floor space costs from $98,000 to $34,300 and yield up to

$63,700 in annual savings versus competitive offerings.

visit www.panduit.com/Cabinets

5

Seal, Direct, Contain, and Monitor
to Improve your PUE

Panduit Energy Efficient Data Center Cabinet System provides
total separation allowing higher data center set points and
reduced cooling system energy consumption by up to 40%.

Seal every gap for complete separation of
cooling and exhaust air

Net-Access™ Cabinets and Sealing Accessories eliminate leakage through
the cabinet structure preventing re-circulation of hot exhaust air back into
equipment inlets.



Direct cold air to where it needs to go

Net-Access™ In-Cabinet Ducting directs cool air directly into the
intake fans preventing recirculation and reducing inlet air temperature
by as much as 14°C, lowering fan energy consumption6.


Contain cooling and exhaust air for maximum
cooling capacity efficiency

Net-Contain™ Vertical Exhaust Duct and Cold Aisle Containment Systems
eliminate hot air recirculation and mixing with cold air allowing room and
chilled water temperature set points to be raised and PUE to be lowered.


Monitor to maintain operational and energy efficiency

Once the physical infrastructure has been optimized for thermal efciency,
Panduit® SmartZone™ Solutions allow continuous monitoring
of highly accurate, granular PUE measurements in real-time to maintain
thermal efciency in dynamic data center environments.

5

5 Impact of Air Containment Systems, Panduit White Paper #WP-20, June 2012
6 The Use of In-Cabinet Ducting to Improve Inlet Air Temperatures, Panduit White Paper RKAT02--WW-ENG, December 2012

6

visit www.panduit.com/Cabinets

Net-Contain™ Vertical

Exhaust Duct

FiberRunner® and

Wyr-Grid® Overhead Cable

Pathway Systems

Sealing

Accessories

Net-Access™

S-Type Cabinets

Panduit® SmartZone™ Solutions

Net-Access™

N-Type Cabinets

The Energy Efcient Data Center Cabinet System can be seamlessly integrated with all elements of the Panduit Converged Infrastructure Solutions, including
Overhead Cable Pathway Systems, High Speed Data Transport (HSDT) Cabling, Grounding and Bonding and Physical Infrastructure Systems.

Software and Hardware

visit www.panduit.com/Cabinets

7

Seal Every Gap for Complete Separation
of Cold Intake and Hot Exhaust Air

Cabinet Top Seal

Net-Access
pre-installed 1.5" x 5" or 3.5" x 5" cabinet top
covers and cable protection bezels to eliminate
air leakage from unused cable entry holes.

™

Cabinets are provided with

Complete Air Seal Features Reduce Air Leakage
Throughout the Cabinet Structure by as much as 25%

Net-Access™ Cabinets have been designed to eliminate every
possible air gap other than those needed to mount equipment.
This minimizes by-pass air and recirculation in the cabinet
providing lower inlet temperatures.

7

Tool-Less Blanking Panels

Snap-In Panels optimize cooling efciency
by eliminating bypass airow and hot air
mixing in cabinets.

Scan to learn more about the

Cool Boot® product overview.

8

visit www.panduit.com/Cabinets

Cool Boot® Cabinet Top Air Sealing Fitting
Eliminate air leakage where data cable bundles enter
the cabinet.

Cool Boot® Raised Floor Grommet

Stop bypass air in new or retrot raised oor applications
where power and data cable pass through a cutout into a
rack or cabinet, saving $46 per oor tile cutout annually8.

7 Maximizing Cooling Energy Efciency with Effective Cabinet Sealing, Panduit White Paper RKAT01-WW-ENG, March 2013
8 The Importance of Air Sealing Grommets to Improving Smart Data Center Cooling Efciency, Panduit White Paper #WW-CPWP-04, August 2008

Direct Cold Air To Where It Is Needed

Net-Direct™ Inlet Ducts enable optimized containment
by effectively directing airflow to improve
network reliability

• Inlet duct solutions deliver cooling air directly from the
cold aisle into the intake fans of switches

• Inlet ducts are completely passive, requiring no energy
to operate and eliminating a point of failure

• Ensures front to back cooling airow which enables
an effective deployment of network switches with
a Net-Contain

• Inlet ducts enable reduced fan power energy consumption
by allowing lower fan speeds, improving the reliability
of the switch

Available for: Cisco^ Nexus, Catalyst and MDS Switches and Juniper EX Series Switches

™

Cold Aisle Containment deployment

Direct Hot Air To Where It Needs To Exhaust

Net-Direct™ Exhaust Ducts direct hot exhaust air out
of a cabinet away from adjacent devices within
non-contained environments

• Exhaust duct solutions channel hot exhaust air directly to
the hot aisle, away from the cold air inlet of adjacent switches

• Exhaust ducts are completely passive, requiring no energy
to operate and eliminating a point of failure

• Ensures switch exhaust airow is directed to the hot aisle
enabling effective deployment of network switches with a
standard hot aisle/cold aisle conguration

• Exhaust ducts enable reduced fan power energy consumption
by allowing lower fan speeds, improving the reliability
of the switch

Patented9 In-Cabinet Ducting optimizes cooling system efciency by establishing front-to-back airow
patterns through the cabinet.

Available for: Cisco^ Nexus and Catalyst Switches

^Cisco is a registered trademark of Cisco Technology, Inc.

9 Patents #8,035,965, #7,855,885 and #7,595,985 - Network Cabinet with Thermal Air Flow Management System

visit www.panduit.com/Cabinets

9

Contain Cold Air or Hot Air to Maximize Cooling
and Space Capacity Utilization

Net-Contain™ Aisle Containment Systems
Deliver Efficient Cooling for High Density Applications

Data Center Managers, challenged to maximize the utilization of available rack-space and cooling capacity, often increase the power density per cabinet.
As cabinet power densities rise, containment architectures are the optimal approach, ensuring uniform cooling air temperature is delivered to equipment in
high density PODs allowing full utilization of available cabinet space and cooling capacity.

Scan to view the Panduit® Net-Contain™ Cold Aisle Containment

Application at EMC’s Durham North Carolina Data Center.

Net-Contain™ Aisle Containment System Benefits

• Data Center Design Versatility – Translucent panels provide built-in provisions for re suppression, environmental monitoring,
security devices and other utilities to accommodate all application requirements

• Complete Application Flexibility – System can be used for slab oor or raised oor applications. Modular design enables varying
aisle widths and accommodates intermixed Net-Access™ Cabinet widths and in-row coolers to support various network architectures
and heat densities

• Reduced Operational Costs – Sliding doors allow easy accessibility for efcient moves, adds and changes and automatically return
to closed position optimizing air containment. Net-Contain™ Components are engineered to seal, minimizing leakage to less than 3%

10

visit www.panduit.com/Cabinets

Net-Contain™ Vertical Exhaust Duct

Above Ceiling Hot Air Return

Raised Floor Cold Air Supply*

Cold
Aisle

Cold
Aisle

Cold
Aisle

Hot

Aisle

Hot

Aisle

Data Center Utilizing Panduit ® Net-Contain™
Vertical Exhaust Duct

•Uniform distribution of cool air reaching the top of the cabinet

•Hot exhaust air is isolated and ducted directly to CRAH units

Passive Cooling for High Density Applications

Net-Contain™ Vertical Exhaust Duct (VED) Systems optimize cooling energy utilization to support high density heat loads to enable 30kw or greater per cabinet.
VEDs passively separate hot exhaust air from cooling air and direct hot exhaust air from active equipment into the Computer Room Air Handler (CRAH)
air return system, allowing higher return air temperature improving CRAH and heat exchanger system efciency up to 40% or more.

Above Ceiling Hot Air Return

Cold
Aisle

Hot

Aisle

Raised Floor Cold Air Supply*

Cold
Aisle

Hot

Aisle

Typical Data Center

•Cool air does not reach the top portions of the cabinets,
making servers in the top rack units vulnerable to overheating

•Hot exhaust air follows complex airow path back to
CRAH units

Above Ceiling Hot Air Return

Cold
Aisle

Cold
Aisle

Hot

Aisle

Raised Floor Cold Air Supply*

Cold
Aisle

Data Center Utilizing Panduit ® Net-Contain™
Vertical Exhaust Duct

•Uniform distribution of cool air reaching the top of the cabinet

Scan to view the Panduit® Net-Contain™ Vertical

•Hot exhaust air is isolated and ducted directly to CRAH units

Exhaust Duct Application at Cisco Allen Data Center.

Net-Contain™ Vertical Exhaust Duct System Benefits

• Flexibility and Versatility – Multiple sizes, heights and adjustable height features allow system to adapt to virtually any data center
structure including slab oors or raised oors and facilities with or without drop ceilings

• Speed Deployment and Reduce Installation Cost – Fast, simple assembly and integral ceiling seal reduce installation time
by 30% compared to competitive offerings

• Enhance Your Data Center Environment – Vertical Exhaust Duct and Net-Access™ Cabinets with sealed, solid rear doors dampen
equipment noise

• Bond Vertical Exhaust Duct with single connection improves system reliability and protection to personnel – Entire VED
is fully electrically bonded to the cabinet requiring no grounding whips for protection of equipment and personnel

visit www.panduit.com/Cabinets

Hot

Aisle

Cold
Aisle

11

Monitor to Maintain Operational
and Energy Efficiency

Data center managers are challenged to maintain and manage energy efciency gains in a highly dynamic, virtualized environment in which power consumption,
environmental and capacity utilization variables are constantly changing. Without the ability to monitor these variables in the data center, efciency gains, PUE
reductions and the ability to maximize capacity utilization while maintaining SLA’s will erode over time leading to a higher total cost of ownership.

PUE

2.0

1.5

1.0

OPEX

increases as

PUE Rises

Time

Energy Efficiency Managed

when Monitored with

Panduit

®

SmartZone™ Solutions

Un-Monitored

PUE

Increased
TCO



Panduit® SmartZone™ Solutions
Enable Real-Time Monitoring, Visualization, and Reporting

Panduit® SmartZone™ Solutions offer software, hardware and services that provide management information by monitoring power and environmental
conditions in real time from the entire facility, down into individual cabinets. This capability enables the data center manager to optimize capacity and reduce
CapEx and OpEx costs.

Power and environmental monitoring is only one component of Panduit’s DCIM offering. SmartZone™ Software also enables the tracking, allocation,
and utilization of critical IT assets within your data center.

12

visit www.panduit.com/Cabinets

Rack Power Distribution Units (PDUs)

Power and Environmental Hardware

As power densities increase, monitoring of power and environmental information using an intelligent rack power distribution unit (PDU) is critical to
preventing power overload and downtime. Panduit supports power and environmental management through two distinct intelligent PDU families:
SmartZone™ Network-Enabled Rack PDUs that connect directly to the network and SmartZone™ Gateway-Enabled Rack PDUs which connect
via a gateway. SmartZone™ Rack PDUs integrate seamlessly into Panduit® SmartZone™ Software, enabling real-time monitoring of physical
infrastructure power consumption, temperature, and humidity levels for enhanced system reliability and operational efciencies. (See pages 34
and 37 for a list of PDU and sensor part numbers).

Panduit’s comprehensive rack PDU offering is available globally in a variety of power congurations to match typical applications, and can be
congured to meet customer specic needs.

Rack Power Distribution Units (PDUs) – Safely and efciently manage and distribute power to multiple devices through a single

power connector to enhance scalability of network build outs.
Through integration with the SmartZone™ Software Suite, rack PDUs send power and temperature readings to allow:

• Automated documentation and visualization of power utilization and environmental conditions

• Recognition and notication of faults or power disruptions

• Identication of available related capacity

Environmental Sensors – Environmental Sensors are available in wired or wireless options, to measure and trend environmental

conditions such as temperature and humidity levels, at the cabinet level. These intelligent sensors transmit real-time environmental information,
providing notication of exceeded thresholds to quickly identify and resolve issues, identify hot and cold spots in the data center and automate
collection of real-time and accurate environmental information.

These sensors send cabinet-level information to the SmartZone™ Software to allow:

• Automated documentation and visualization of temperature and humidity levels

• Recognition and notication of exceeded temperature thresholds and/or other environmental-specic concerns

• Trending analysis to uncover developing thermal issues that may impact optimal performance and efciency

visit www.panduit.com/Cabinets

13

Net-Access™ N-Type Cabinets

Optimum Accessibility and Cable Management for High Density Applications

Net-Access™ N-Type Cabinets are the rst choice for data center managers and systems
integrators specifying high density network, storage and compute applications that
require optimal thermal management and the capacity to manage high cable densities.

Integral cabinet air seal features and integration with passive hot and cold air containment
components drive efcient utilization of cooling capacity and reduce cooling energy
consumption. The Net-Access™ inset frame design efciently manages large quantities of
cables and provides space for unmatched access reducing operational costs. This industry
leading design also maximizes airow and provides easy access to equipment for ongoing
operational efciencies, providing exceptional value in a 800mm (31.5") wide enclosure.

Inset frame provides up to 10%
more space for cable management
and cooling airflow

Industry leading inset cabinet frame posts
create a large area for airow to provide
proper heat dissipation and enable easy
access to equipment, in-cabinet ducting
and cabling, speeding deployments and
reducing operational costs.

Dual hinged doors speed deployments
and moves, adds, and changes up to 30%

IT staff is scarce, downtime is expensive.
For a 120 rack dynamic data center, our
cabinets save you up to an hour a day,
adding up to $18,250 per year savings
for your staff.

Efficiently manage high
cable densities

Modular snap in ngers align with rack
spaces to simplify cable management,
providing proper bend radius control and
organizing cables for faster moves, adds
and changes and installations.

14

visit www.panduit.com/Cabinets

Open rail mounting creates more
cable management space and
equipment positioning flexibility

High strength frame eliminates need for
support members between rails, providing
unobstructed space between the frame
and the side panels.

Vertical split side panels
enable fast access to equipment

Innovative vertical split side panels
and optional vertical split hinged side
panels allow fast easy access to end
of row network equipment and cabling,
eliminating time consuming handling.

Innovative Leveling Feet Design
Reduces Cabinet Installation
Time up to 80%

Heavy duty, M14 thread top drive
leveling feet are easily accessed and
allow cabinets to be leveled in less time
than typical leveling feet.

Bond cabinets to the
telecommunications grounding
infrastructure with single connection,
reducing installation time

Entire cabinet is fully electrically
bonded, requiring no grounding whips
to doors or side panels for protection
of equipment and personnel.

visit www.panduit.com/Cabinets

15

Net-Access™ S-Type Cabinets

Cost Effective and Versatile Cabinets for all Data Center
Applications and Facilities Designs

Net-Access™ S-Type Cabinets provide data center managers and systems integrators an
unprecedented range of features in a cost effective cabinet platform for server, network,
and pre-congured cabinet applications.

Integral cabinet air seal features and seamless integration with passive hot and cold air containment
components provide efcient utilization of cooling capacity, and contribute to reduced cooling energy
consumption. An innovative frame design maximizes RU utilization saving as much as 15% of the oor
space while safely accommodating equipment loads. Offered in a variety of widths, heights,
and depths, they can be specied for a variety of applications in any facility to meet the diverse
application needs of today’s data centers.

700mm (28") W

600mm (24") W

Large selection of standard cabinet widths, heights, and depths offered in:

• 600mm (24"), 700mm (28"), and 800mm (31.5") Widths

• 1070mm (42") and 1200mm (48") Depths

• 42 RU, 45 RU, and 48 RU Heights

• Black and White Color Option

• Static Load Rating 1,364kg (3,000 lb.)

• Rolling Load Rating 1,136kg (2,500 lb.)

800mm (31.5") W

16

visit www.panduit.com/Cabinets

Out-Set Cable Entry Improves
Floor Space Utilization up to 5%

Network cable entry locations are
outside of equipment area, allowing
top 2 RUs to be used, optimizing
cabinet utilization and saving
oor space.

Zero RU E-Rail Vertical Patching Adds
Capacity and Improves Floor Space
Utilization by 10%

Unique Zero RU E-Rail is the industy's
only vertical patching system for 600mm
(24") wide cabinets integrating with
Quick-Net™ Copper and Fiber Cabling
Systems, optimizing cabinet utilization
and saving oor space.

Innovative Leveling Feet Design
Reduces Cabinet Installation
Time by 80%

Heavy duty, M14 thread top drive
leveling feet are easily accessed and
allow cabinets to be leveled in less time
than typical leveling feet.

A 15% savings in floor space means you can build a 420 server POD

with 10 server cabs versus a competitors' cabinet that would require

12 server cabinets to hold equivalent amount of servers.

CapEx savings10 $900/ft2 x 16ft2 = $14,400 capital savings per POD.

10) Cost Model: Dollars per kW plus Dollars per Square Foot of Computer Floor, Uptime 2008

visit www.panduit.com/Cabinets

17

Simplify and Accelerate Data Center Deployments

Net-Access™ Cabinets Enable Convergence of Network Equipment

Converged Infrastructure Solutions Add Value
and Reduce Installation Time and Cost

Dynamic rated Net-Access™ N-Type and S-Type Cabinets allow
pre-installation of IT equipment for faster deployments and time to
production. Panduit Converged Infrastructure Solutions are fully tested and
validated physical infrastructures that ensure best practice installations
and optimal system performance. Each conguration accelerates
deployment and promotes rapid upgrades requiring zero recongurations
and downtime.

Fast, Single Part Number Quoting and Procurement

Simply attach pre-priced, robust Converged Infrastructure Solutions to
active gear quotes:

• Reduce quote time

• Procure complete infrastructures with a single part number

• Ensure accurate delivery of all parts to the job site

Maximize the Speed of Deployment and
Overall Execution

Converged Infrastructure Solutions can save up to 80% in deployment time.

• Solutions arrive pre-assembled, kitted, and ready to rack and roll

• Factory installed cable managers, patch cable kits, and cabling
instructions ensure a precise deployment and
professional appearance

Deployment
Fulllment

Design

Plan

Assess

Time to Production

Typical Panduit Converged

Infrastructure Solutions

Reduced Time to Production
up to 80%

Arrive factory designed, tested,
and validated to improve:

• Assessment time up to 80%

• Planning time up to 80%

• Design time up to 80%

• Fulllment time up to 90%

• Deployment time up to 65%

Refer to Panduit Converged
Infrastructure Solutions For Cisco^
Nexus, UCS, and Catalyst Platforms,
RKCB34--SA-ENG

Converged Infrastructure for
Nexus 7009 "Heavy Copper"

Major Private Cloud Provider

reduced system assembly

time by up to 7 hours per

cabinet, improving cost

and speeding delivery.

^Cisco is a registered trademark of Cisco Technology, Inc.

18

visit www.panduit.com/Cabinets

Net-Access™ Cabinet and Thermal Management
Solution for Cisco^ Nexus 7018 Switch

Panduit offers a Net-Access™ Cabinet solution designed to meet the thermal and
operating requirements of the modular, high density Cisco^ Nexus 7018 Switch.
Based on a standard 800mm (31.5") wide Net-Access™ N-Type Cabinet, an
easy to use expansion module provides space to route and manage high
densities of cables. Internal ducting enables front to back cooling air ow
and improved reliability.

Simple conversion for
Standard 800mm N-Type Cabinet

Extension kit enables 800mm
Net-Access™ N-Type Cabinet to be
extended to 1,000mm (40") wide, reducing
shipping costs and simplifying handling.

Passive inlet and exhaust duct
ensures cooling airflow

Prevents recirculation of exhaust air into
the switch, ensuring lower inlet temperature
and reduced fan energy consumption.

Cable management fingers
route, manage and protect
high cable densities

Fingers align with rack spaces to
ensure proper bend radius and superior
management of high densities of I/O
cables, keeping them clear of cold air
ow while maintaining access to power
supplies and fan modules, reducing
operational costs.

Net-Access™ N-Type Cabinet with Cisco^ Nexus 7018

Extension Kit Installed

^Cisco is a registered trademark of Cisco Technology, Inc.

visit www.panduit.com/Cabinets

19

Net-Access™ Integral Cabinet Top Cable Routing System

Speed deployments and optimize overhead space utilization

Net-Access™ Cabinets are available with an Integral Cabinet Top Cable Routing System that protects, routes, and manages large
quantities of twisted pair data cables into and out of any Net-Access™ Cabinet. This versatile system is integral to the top of the cabinet
and easily integrates with other cable pathways used throughout the data center, providing up to a 30% reduction in installation costs.

Net-Access

20

™

Integral Cabinet Top Cable Routing System deployed on Net-Access™ Cabinets.

visit www.panduit.com/Cabinets

Net-Access™ N-Type Cabinet Specifications

• Welded and assembled steel frame construction

• Easy maintenance powder coat nish

• Adjustable rear equipment rails with continuous positioning,
xed front rails

• Large cable entry/cable access

• Doors include keyed swing handles

• Side panels

• Dual hinge door for maximum accessibility between
adjacent cabinets

• Cabinet supplied with 2 sets of high density cable management
ngers (SN25F)

Net-Access

• Welded and assembled steel frame construction

• Easy maintenance powder coat nish

• Adjustable rear equipment rails with continuous positioning,
xed front rails

• Doors include keyed swing handles

• Side panels include keyed quarter-turn latches

• Large cable entry/cable access

• PDU brackets (SPDUBRK) included

™

S-Type Cabinet Specifications

• Cable entry holes are equipped with plastic sealing plugs

• UL 2416 standard compliant and have been static load tested to
1,360kg (3,000 lb.)

• EIA-310-E compliant

• Rolling Load of 1,136kg (2,500 lb.)

• Cabinet ships assembled, one per pallet

• N-Type Cabinets include hardware kit: #12-24 screws,
or M6 screws and cage nuts

• Casters are supplied separately

• Cable entry holes are equipped with plastic sealing plugs

• UL 2416 standard compliant and have been static load tested to
1,360kg (3,000 lb.)

• EIA-310-E compliant

• Rolling Load of 1,136kg (2,500 lb.)

• Cabinet ships assembled, one per pallet

• S-Type Cabinets include hardware kit: M6 screws, and cage nuts

• Vertical airdams included

• Casters are pre-installed

Net-Access™ Cable Capacity Charts

Top Cap Opening Cable Capacity

Area Cable Capacities

Cat. 6A

Opening Size In.

5" x 3.5"

5" x 1.5"

Cabinet Size

(mm) In.

15.6 100.7 63 82 90 127 227 569 8

6.5 42.2 26 34 37 53 95 239 8

2

Area Cable Capacities

2

Cm.

Cm.

2

2

0.354"

(8.99mm)

Cat. 6A

0.354"

(8.99mm)

N-Type (Front Side)

800x1070 43.8 282.7 178 232 252 357 638 1599

800x1200 43.8 282.7 178 232 252 357 638 1599

S-Type (Rear Side)

600x1070

600x1200

700x1070

700x1200

800x1070 46.3 298.4 187 245 267 376 673 1688

800x1200 76.3 491.9 309 404 440 621 1110 2783

18.5 119.4 75 98 106 150 269 675

30.5 196.8 123 161 176 248 444 1113

32.4 208.9 131 171 186 263 471 1181

53.4 344.4 216 282 308 434 777 1948

Cat. 6A

0.310"

(7.87mm)

Cable Pathways (Per Side)

Cat. 6A

0.310"

(7.87mm)

Cat. 6A

0.297"

(7.54mm)

Cat. 6A

0.297"

(7.54mm)

Cat. 6

0.250"

(6.35mm)

Cat. 6

0.250"

(6.35mm)

Cat. 5e

0.187"

(4.75mm)

Cat. 5e

0.187"

(4.75mm)

visit www.panduit.com/Cabinets

Fiber

(3mm)

Fiber

(3mm)

QuickNet

Cassettes

™

21

™

Net-Access

N-Type and S-Type Cabinet

Offering and Availability Overview

Multiple cabinet solutions to meet your project goals – from standard cabinets for quick turnaround to customer congured cabinet
for specic deployments, Net-Access™ N-Type and S-Type Cabinets provide a complete solution to meet customer requirements.

Quick

Turnaround

Net-Access™ N-Type and S-Type Standard Cabinets

™

N-Type and S-Type Standard Congured Cabinets

Net-Access

™

N-Type and S-Type Customer Congured Cabinets

N-Type and S-Type
Customer Congured Cabinets

• Congured to customer specications

• Multiple widths

• Multiple heights

• Multiple depths

• With or without side panels

• Black, white or gray nish

• Door options

• Thermal options

• Equipment rail options

• Top cap options

• Caster options

• Standard accessories pre-installed
to customer specications

Build to

Order

N-Type and S-Type
Standard Cabinets

• Quick turnaround

• 3 widths – 600mm, 700mm, 800mm

• 2 heights – 42 RU, 45 RU

• 2 depths – 1070mm, 1200mm

• With or without side panels

• Black nish

• Standard doors

Net-Access

Options

N-Type and S-Type
Standard Congured Cabinets

• 3 widths – 600mm, 700mm, 800mm

• 3 heights – 42 RU, 45 RU, 48 RU

• 2 depths – 1070mm, 1200mm

• With or without side panels

• Black or white nish

• Door options

• Thermal options

• Equipment rail options

• Top cap options

• Caster options

Net-Access™ N-Type and S-Type Standard Cabinets

42 RU N8212B S8212B S7212B S6212B

45 RU N8512B S8512B S7512B S6512B

With Side Panels

Without Side

Panels

42 RU N8222B S8222B S7222B S6222B

45 RU N8522B S8522B S7522B S6522B

42 RU N8219B S8219B S7219B S6219B

45 RU N8519B S8519B S7519B S6519B

42 RU N8229B S8229B S7229B S6229B

45 RU N8529B S8529B S7529B S6529B

N-Type Standard Components:

• #12-24 tapped rails

• Dual hinge front door/split rear door

• No PDU brackets

• Two sets of ngers

• Solid side panels

• No casters

22

visit www.panduit.com/Cabinets

N-Type Width S-Type Width

800mm 800mm 700mm 600mm

1070mm depth

1200mm depth

1070mm depth

1200mm depth

S-Type Standard Components:

• Cage nut rails

• Single hinge front door/split rear door

• Caster and PDU brackets included

• Cable management optional

Net-Access™ N-Type Standard Configured Cabinets

Series Width Height Depth Side Panels Color Standard Options (Select Only One)

N 8 = 800mm 2 = 42 RU

5 = 45 RU

8 = 48 RU

*Standard side panel. **Includes #12-24 tapped equipment rails. V, Y and YT - Only available for 1200mm deep cabinets. See page 25.

Standard Congurations have 6 characters with only one standard option sufx.

N 8 2 1 2 B

™

Net-Access

Series Width Height Depth Side Panels Color Standard Options (Select Only One)

S 6 = 600mm

7 = 700mm

8 = 800mm

*Standard side panel. P - Only available for 600mm wide S-Type Cabinets. V and V9 - Only available for 1200mm deep cabinets. See page 25.

S-Type Standard Configured Cabinets

2 = 42 RU

5 = 45 RU

8 = 48 RU

1 = 1070mm

2 = 1200mm

1 = 1070mm

2 = 1200mm

2 = 2 Side Panels*

9 = No Side Panel

2 = 2 Side Panels*

9 = No Side Panel

B = Black

W = White

B = Black

W = White

C = Cage Nut Rails

E = Single Hinge Front Door and Cage Nut Rails

S = No Doors**

T = Integral Cabinet Top Cable Routing System**

TC = Integral Cabinet Top Cable Routing System and
Cage Nut Rails

U = Vertical Blanking and Cage Nut Rails

V = VED Ready**

Y = VED Ready and Cage Nut Rails

YT = VED Ready, Cage Nut Rails, and Integral Cabinet Top
Cable Routing System

A = Switch Congured with Front Cable Management
(PDU bracket not included)

A9 = Switch Congured with Front Cable Management and
No Casters

F = Vertical Cable Management Fingers

P = Vertical Patching Equipment Rails

S = No Doors

T = Integral Cabinet Top Cable Routing System

T9 = Integral Cabinet Top Cable Routing System and
No Casters

V = VED Ready

V9 = VED Ready and No Casters

9 = No Casters

Standard Congurations have 6 characters with only one standard option sufx.

S 6 2 1 2 B

Net-Access™ N-Type and S-Type Customer Configured Cabinets

Cabinets can be congured to customers' specications. Multiple options are listed below, below, but may not be available for all
congurations. For other possible options please contact your sales person or Customer Service.

• Multiple Widths

• Multiple Heights

• Multiple Depths

• Doors – Single Hinge, Dual Hinge,
Split Doors, or None

• Side Panels – 0, 1, or 2

• Black, White or Gray Finish

• #12-24 Tapped or Cage Nut Rails

• Standard, VED, Integral Cabinet Top Cable
Routing System, or VED and Integral Cabinet
Top Cable Routing System

• Vertical Patching

• Vertical Air Dams

• Cable Management

• Casters

• PDU Brackets

• Combination Locks

visit www.panduit.com/Cabinets

23

Net-Access™ N-Type and S-Type Cabinets with
Integral Cabinet Top Cable Routing System

N-Type Width S-Type Width

800mm 800mm 700mm 600mm

42 RU N8212BT S8212BT S7212BT S6212BT

45 RU N8512BT S8512BT S7512BT S6512BT

48 RU N8812BT S8812BT S7812BT S6812BT

With Side Panels

Without Side

Panels

For other colors replace sufx B (Black) with W (White).

42 RU N8222BT S8222BT S7222BT S6222BT

45 RU N8522BT S8522BT S7522BT S6522BT

48 RU N8822BT S8822BT S7822BT S6822BT

42 RU N8219BT S8219BT S7219BT S6219BT

45 RU N8519BT S8519BT S7519BT S6519BT

48 RU N8819BT S8819BT S7819BT S6819BT

42 RU N8229BT S8229BT S7229BT S6229BT

45 RU N8529BT S8529BT S7529BT S6529BT

48 RU N8829BT S8829BT S7829BT S6829BT

1070mm depth

1200mm depth

1070mm depth

1200mm depth

N-Type Integral Top Cabinet Components:

• 12-24 tapped rails

• Dual hinge front door/split rear door

• No PDU brackets

• Two sets of ngers

• No casters

S-Type Integral Top Cabinet Components:

• Cage nut rails

• Single hinge front door/split rear door

• No cable management

• Caster and PDU brackets included

24

visit www.panduit.com/Cabinets

Net-Access™ N-Type and S-Type Vertical Exhaust Duct
(VED) Cabinets (VED Sold Separately)

N-Type Width S-Type Width

800mm 800mm 700mm 600mm

42 RU N8222BV S8222BV S7222BV S6222BV

With Side Panels

Without Side

Panels

* VED cabinets only available in 1200mm depths.
For other colors replace sufx B (Black) with W (White).

45 RU N8522BV S8522BV S7522BV S6522BV

48 RU N8822BV S8822BV S7822BV S6822BV

42 RU N8229BV S8229BV S7229BV S6229BV

45 RU N8529BV S8529BV S7529BV S6529BV

48 RU N8829BV S8829BV S7829BV S6829BV

1200mm depth

1200mm depth

N-Type VED Cabinet Components:

• #12-24 tapped rails

• Dual hinge front door/solid rear door

• No PDU brackets

• 2 sets of ngers

• VED top cap ready

• Vertical blanking panels with pass-throughs

• Rear oor seals

• No casters

S-Type VED Cabinet Components:

• Cage nut rails

• Single hinge front door/solid single hinge rear door

• No cable management

• VED top cap ready

• Vertical blanking panels

• Front and rear oor seals

• Caster and PDU brackets included

Net-Contain™ Vertical Exhaust Ducts (VEDs)

Part Number Description

Net-Contain™ Vertical Exhaust Duct for Net-Access™ N-Type and S-Type Cabinets

C2VED**I1626^^ Net-Contain™ VED **mm width cabinet – 406mm (16") up to 660mm (26") height – ^^ colored.

C2VED**I2638^^ Net-Contain™ VED **mm width cabinet – 660mm (26") up to 965mm (38") height – ^^ colored.

C2VED**I3866^^

** = 08 = 800mm, 07 = 700mm, 06 = 600mm ^^ = B1 = Black, W1 = White.

Net-Contain™ VED **mm width cabinet – 965mm (38") up to 1,676mm (66") height – ^^ colored.

visit www.panduit.com/Cabinets

25

Net-Contain™ Cold and Hot Aisle Containment

Part Number Description

Net-Contain™ Aisle Containment Sliding Doors

C2CACT5F**SD^^ Net-Contain™ Sliding Door CAC for **ft (**mm) aisle- capable of 42 up to 45 RU – ^^ colored.

** = 04 = 4ft (1200mm), 06 = 6ft (1800mm) ^^ = B1 = Black, W1 = White.

Net-Contain™ Integral Low Prole Ceiling Structure for Net-Access™ N-Type and S-Type Cabinets

C2CAC08F**IR^^ Net-Contain™ (CAC) Integral Roof for 800mm width cabinet with **ft (**mm) aisle width – ^^ colored.

™

C2CAC07F**IR^^ Net-Contain

C2CAC06F**IR^^ Net-Contain

** = 04 = 4ft (1200mm), 06 = 6ft (1800mm) ^^ = B1 = Black, W1 = White.

Net-Contain™ Integral Roof Wall Panels

C2CAC**F08WP^^ Net-Contain™ Integral Roof Wall Panel for **mm width cabinet – ^^ colored.

** = 08 = 800mm, 07 = 700mm, 06 = 600mm ^^ = B1 = Black, W1 = White.

Net-Contain™ Row Base Cooling Blanking Panels

C2CAC**ABWPA^^ For cold aisle containment systems using row base cooling equipment.

** = 06 = 600mm, 04 = 400mm, 03 = 300mm ^^ = B1 = Black, W1 = White.

Net-Contain™ Aisle Containment Sliding Doors

C2CACT5F04SD^^ Net-Contain™ Sliding Door CAC for 4 ft. (1200mm) aisle- capable of 42 up to 45 RU – ^^ colored.

^^ = B1 = Black, W1 = White

Sliding Door Frame Adapter for 4' (1200mm) Aisle Containment Sliding Doors

C2HACT8F04DFB1^^ Net-Contain™ Hot Aisle Containment Sliding Door Frame Adapter for 4 ft. (1200mm) aisle, capable of 42 RU

up to 48 RU.

(CAC) Integral Roof for 700mm width cabinet with **ft (**mm) aisle width – ^^ colored.

™

(CAC) Integral Roof for 600mm width cabinet with **ft (**mm) aisle width – ^^ colored.

C2HACT8F04DFB

C2HAC**I1626
C2HAC**I2638
C2HAC**I3866

C2HACERI1626
C2HACERI2638
C2HACERI3866

26

visit www.panduit.com/Cabinets

^^ = B1 = Black, W1 = White

Net-Contain™ Adjustable Vertical Wall for Net-Access™ N-Type and S-Type Cabinets

C2HAC**I1626^^ Net-Contain™ Hot Aisle Containment Adjustable Vertical Wall (16" - 26") for **mm width cabinets.

™

C2HAC**I2638^^ Net-Contain

C2HAC**I3866^^ Net-Contain

** = 06 = 600mm, 04 = 400mm, 03 = 300mm ^^ = B1 = Black, W1 = White.

Hot Aisle Containment Adjustable Vertical Wall (26" - 38") for **mm width cabinets.

™

Hot Aisle Containment Adjustable Vertical Wall (38" - 66") for **mm width cabinets.

Adjustable EOR Vertical Wall

C2HACERI1626^^ Net-Contain™ Adjustable End of Row Vertical Wall (16" - 26") for 900mm/1000mm/1200mm aisle widths.

™

C2HACERI2638^^ Net-Contain

C2HACERI3866^^ Net-Contain

^^ = B1 = Black, W1 = White

Adjustable End of Row Vertical Wall (26" - 38") for 900mm/1000mm/1200mm aisle widths.

™

Adjustable End of Row Vertical Wall (38" - 66") for 900mm/1000mm/1200mm aisle widths.

Net-Contain™ Universal Aisle Containment System

Part Number Description

CUEFRT8F**ST
CUEFRT9F**ST

CUSMPR52ST01B1

CUCMSS**ST01NC

C2CACT5F**SD

CURFS06F**HB
CURFS07F**HB
CURFS08F**HB

C2HACERI1626
C2HACERI2638
C2HACERI3866

CUVWA06S**ST

C2HAC**I1626
C2HAC**I2638
C2HAC**I3866

CUVWB12S12ST

CUWBSS**ST01

CUWBPS**ST02

CUFBPR**06HB

CUTBPR0610HBN1

Net-Contain™ End of Row Frame for Roong

CUEFRT8F**ST^^ Net-Contain™ UAC End of Row Frame for Roong - 42/45 RU high.

™

CUEFRT9F**ST^^ Net-Contain

** 04 = 4' (1200mm) aisle width, 06 = 6' (1800mm aisle width) ^^ = B1 = Black, W1 = White.

UAC End of Row Frame for Roong - 48/52 RU high.

Net-Contain™ Mid-Span Post

CUSMPR52ST01B1 Net- Contain™ Mid-Span Post 42 RU to 52 RU high.

Net-Contain™ Mid-Span Cabinet Support

CUCMSS**ST01NC Net-Contain™ Mid-Span Cabinet Support

**03 = 300mm, 06 = 600mm

Net-Contain™ Aisle Containment Sliding Doors

C2CACT5F**SD^^ Net-Contain™ Sliding Door CAC for **ft (**mm) aisle- capable of 42 up to 45 RU – ^^ colored.

** = 04 = 4ft (1200mm), 06 = 6ft (1800mm) ^^ = B1 = Black, W1 = White.

Net-Contain™ Integral Ceiling Structures

CURFS06F**HB^^ Net-Contain™ 600mm Roong Section.

™

CURFS07F**HB^^ Net-Contain

CURFS08F**HB^^ Net-Contain

** 04 = 4' (1200mm) aisle width, 06 = 6' (1800mm aisle width) ^^ = B1 = Black, W1 = White.

700mm Roong Section.

™

800mm Roong Section.

Net-Contain™ End of Row Frame for Vertical Walls 42/45 RU High

CUEFVT8F04ST^^ Net-Contain™ End of Row Frame for Vertical Walls - 42/45RU - 4ft. (1200mm) aisle width.

^^ = B1 = Black, W1 = White.

Adjustable EOR Vertical Wall

C2HACERI1626^^ Net-Contain™ Adjustable End of Row Vertical Wall (16" - 26") for 900mm/1000mm/1200mm aisle widths.

™

C2HACERI2638^^ Net-Contain

C2HACERI3866^^ Net-Contain

^^ = B1 = Black, W1 = White

Adjustable End of Row Vertical Wall (26" - 38") for 900mm/1000mm/1200mm aisle widths

™

Adjustable End of Row Vertical Wall (38" - 66") for 900mm/1000mm/1200mm aisle widths.

Net-Contain™ Vertical Wall Adapter

CUVWA06S**ST^^ Net-Contain™ Vertical Wall Adapter

**06 = 600mm, 07 = 700mm, 08 = 800mm ^^ = B1 = Black, W1 = White.

Net-Contain™ Adjustable Height Vertical Walls

C2HAC**I1626^^ Net-Contain™ Adjustable Vertical Wall (16" - 26").

™

C2HAC**I2638^^ Net-Contain

C2HAC**I3866^^ Net-Contain

**06 = 600mm, 07 = 700mm, 08 = 800mm ^^ = B1 = Black, W1 = White.

Adjustable Vertical Wall (26" - 38").

™

Adjustable Vertical Wall (38" - 66").

Net-Contain™ Vertical Wall Brace

CUVWB12S12ST^^ Net-Contain™ Vertical Wall Brace, 4 ft. (1200mm) aisle width.

^^ = B1 = Black, W1 = White.

Net-Contain™ Wall Beam

CUWBSS**ST01^^ Net-Contain™ Wall Beam, 1 piece.

™

CUWBPS**ST02^^ Net-Contain

**06 = 600mm, 07 = 700mm, 08 = 800mm, 24 = 2400mm ^^ = B1 = Black, W1 = White.

Wall Beam, 2 pieces.

Net-Contain™ Full Blanking Panel

CUFBPR**06HB^^ Net-Contain™ Full Blanking Panel 600mm wide.

**42 = 42 RU, 45 = 45 RU, 48 = 48 RU, 52 = 52 RU ^^ = B1 = Black, W1 = White.

Net-Contain™ Top of Cabinet Blanking Panel

CUTBPR0610HBN1 Net-Contain™ Top of Cabinet Blanking Panel 600mm high x 1000mm wide.

visit www.panduit.com/Cabinets

27

Net-Access™ Cabinet Accessories

SN15F SN25F

S7VPPB

NERSS

S2BRK6

S1DR

SN8VPPB

NACSS

NVPDUB

SPDUBRK

S2BRK12

S2DR

Part Number

N-Type

Compatible

S-Type

Compatible Description

POU Brackets and Cable Management

SN15F x x Finger Kit, 100mm (3.9") depth that attaches to posts on 42 RU through 48 RU cabinets.

SN25F x x Finger Kit, 150mm (5.9") depth that attaches to posts on 42 RU through 48 RU cabinets.

S7VPPB x Vertical patching bracket for 700mm wide cabinets.

SN8VPPB x x Vertical patching bracket for 800mm wide cabinets.

NERSS x End of row slack spool.

NACSS x Center slack spool for between cabinets, adjustable 210mm (8.3") to 267mm (10.5") .

NVPDUB x PDU brackets, sold in pairs.

SPDUBRK x PDU brackets, sold in pairs.

S2BRK6 x Combination PDU/cable management bracket, 152mm (6") wide full length for

S2BRK12 x Combination PDU/cable management bracket, 305mm (12") wide full length for

S1DR x 1 RU D-ring cable retainer, 80mm (3.1" ) x 40mm (1.5"), bag of 8pcs, attaches

S2DR x 2 RU D-ring cable retainer, 80mm (3.1") x 80mm (3.1"), bag of 8 pcs, attaches

S1LR x 1 RU L-ring cable retainer, 60mm (2.2") x 100mm (3.8"), bag of 8pcs, attaches

S2LR x 2 RU L-ring cable retainer, 85mm (3.4") x 100mm (3.8"), bag of 8pcs, attaches

42 RU through 48 RU cabinet.

42 RU through 48 RU cabinet.

to S2BRK6/S2BRK12.

to S2BRK6/S2BRK12.

to S2BRK6/S2BRK12.

to S2BRK6/S2BRK12.

Casters and Locks

NCSTR4 x Caster Kit. 2 xed casters for front of cabinet, 2 swivel casters for rear of cabinet,

SCSTR4 x Caster Kit. 2 xed casters for front of cabinet, 2 swivel casters for rear of cabinet,

CCL3 x x Three digit combination lock with key over ride for single hinge or split doors.

4 mounting plates and 24 screws. Casters add 24mm (1") to height of cabinet.

and 16 screws. Casters add 24mm (1") to height of cabinet.

S1LR

NCSTR4

SCSTR4

28

visit www.panduit.com/Cabinets

S2LR

CCL3

Net-Access™ Cabinet Accessories (continued)

NVBP

S**SHDB

SN**SDB

Part Number

N-Type

Compatible

S-Type

Compatible Description

Vertical Blanking Panels

NVBP x Vertical blanking panels with pass-through holes for 42 RU through 48 RU cabinets.

S6VBPN x* Vertical blanking panel for 600mm cabinets.

S7VBPN x* Vertical blanking panel for 700mm cabinets.

S8VBPN x* Vertical blanking panel for 800mm cabinets with 25mm (1") x 127mm (5") knock-outs.

Single and Dual Hinge Doors

N82SHDB x Single hinge door for 42 RU 800mm wide cabinet.

N85SHDB x Single hinge door for 45 RU 800mm wide cabinet.

N82DHDB x Dual hinge door for 42 RU 800mm wide cabinet.

N85DHDB x Dual hinge door for 45 RU 800mm wide cabinet.

S62SHDB x Single hinge door for 42 RU 600mm wide cabinet.

S65SHDB x Single hinge door for 45 RU 600mm wide cabinet.

S72SHDB x Single hinge door for 42 RU 700mm wide cabinet.

S75SHDB x Single hinge door for 45 RU 700mm wide cabinet.

S82SHDB x Single hinge door for 42 RU 800mm wide cabinet.

S85SHDB x Single hinge door for 45 RU 800mm wide cabinet.

Split Doors

S62SDB x Split doors for 42 RU 600mm wide cabinet.

S65SDB x Split doors for 45 RU 600mm wide cabinet.

S72SDB x Split doors for 42 RU 700mm wide cabinet.

S75SDB x Split doors for 45 RU 700mm wide cabinet.

SN82SDB x x Split doors for 42 RU 800mm wide cabinet.

SN85SDB x x Split doors for 45 RU 800mm wide cabinet.

* For use with S-Type switch congured cabinets.

visit www.panduit.com/Cabinets

29

Net-Access™ Cabinet Accessories (continued)

N**SPS

N**SPH

S**SPSE

Part Number

N-Type

Compatible

S-Type

Compatible Description

Side Panels

N21SPS x Split side panel for 42 RU 1070mm depth cabinet.

N51SPS x Split side panel for 45 RU 1070mm depth cabinet.

N81SPS x Split side panel for 48 RU 1070mm depth cabinet.

N22SPS x Split side panel for 42 RU 1200mm depth cabinet.

N52SPS x Split side panel for 45 RU 1200mm depth cabinet.

N82SPS x Split side panel for 48 RU 1200mm depth cabinet.

N21SPH x Split hinged side panel for end of row application for 42 RU 1070mm depth cabinet.

N51SPH x Split hinged side panel for end of row application for 45 RU 1070mm depth cabinet.

N81SPH x Split hinged side panel for end of row application for 48 RU 1070mm depth cabinet.

N22SPH x Split hinged side panel for end of row application for 42 RU 1200mm depth cabinet.

N52SPH x Split hinged side panel for end of row application for 45 RU 1200mm depth cabinet.

N82SPH x Split hinged side panel for end of row application for 48 RU 1200mm depth cabinet.

S21SPSE x Split side panel for 42 RU 1070mm depth cabinet.

S51SPSE x Split side panel for 45 RU 1070mm depth cabinet.

S81SPSE x Split side panel for 48 RU 1070mm depth cabinet.

S22SPSE x Split side panel for 42 RU 1200mm depth cabinet.

S52SPSE x Split side panel for 45 RU 1200mm depth cabinet.

S82SPSE x Split side panel for 48 RU 1200mm depth cabinet.

* For use with S-Type switch congured cabinets.

30

visit www.panduit.com/Cabinets

Net-Access™ Cabinet Accessories (continued)

SN7TCDW
SN8TCDW

SN1070CREC
SN1200CREC

SN1200VCREC

RSHLF23

RSHLF

SN*RC

Part Number

N-Type

Compatible

S-Type

Compatible Description

Integral Cabinet Top Cable Routing System

SN8TCDW x x Divider wall with screws for integral cabinet top cable routing system to enhance

SN7TCDW x Divider wall with screws for integral cabinet top cable routing system to enhance

SN1070CREC x x End of row cap kit for integral cabinet top cable routing system. Includes brackets

SN1200CREC x x End of row cap kit for integral cabinet top cable routing system. Includes brackets

SN1200VCREC x x End of row cap kit for integral cabinet top cable routing system. Includes brackets

cable management. For 800mm wide cabinet.

cable management. For 600mm and 700 mm wide cabinets.

and screws for 1070mm deep cabinet.

and screws for 1200mm deep cabinet.

and screws for 1200mm deep VED cabinet.

Shelves

RSHLF23 x x Shelf kit includes mounting bracket and screws. Shelf dimensions:

RSHLF x x Shelf kit includes mounting bracket and screws. Shelf dimensions:

44mm (1.7")H x 483mm (19")W x 584mm (23")D. Load rating 275 lbs. (124kg).

44mm (1.7")H x 483mm (19")W x 762mm (30")D. Load rating 275 lbs. (124kg).

Equipment Rail Sets

SN2RC x x Cage nut rear rails for 42 RU cabinet, sold in pairs.

SN5RC x x Cage nut rear rails for 45 RU cabinet, sold in pairs.

N2RT x Tapped (#12-24 ) rear rails for 42 RU cabinet, sold in pairs.

N5RT x Tapped (#12-24 ) rear rails for 45 RU cabinet, sold in pairs.

™

S2RP x Vertical patching cage nut rails for 42 RU 600mm wide (0 RU QuickNet

S5RP x Vertical patching cage nut rails for 45 RU 600mm wide (0 RU QuickNet

) cabinet.

™

) cabinet.

Floor Seals

N2EOR1BA1070B1 x End of row oor seal for 1070mm deep cabinet.

N2EOR1CA1200B1 x End of row oor seal for 1200mm deep cabinet.

S2EOR1BA1070B1 x End of row oor seal for 1070mm deep cabinet.

S2EOR1CA1200B1 x End of row oor seal for 1200mm deep cabinet.

C2FAB06A1200B1 x Front or back oor seal for 600mm wide cabinet.

C2FAB07A1200B1 x Front or back oor seal for 700mm wide cabinet.

C2FAB08A1200B1 x x Front or back oor seal for 800mm wide cabinet.

N*RT

S*RP

visit www.panduit.com/Cabinets

31

Net-Direct™ In-Cabinet Ducting

CDE1

CDE2

CNLTD21B2

CNLTD52A2

CNLTD142A3

CNLTD72A3

DIBBC2314S21W

Part Number Description

Inlet Ducts

CDE1 Net-Direct™ Air Inlet Duct, 1 RU that resides below the switch provides cold aisle airow to Cisco^ 4948,

CDE2 Net-Direct

CNLTD21B2 Net-Direct

CNLTD52A2 Net-Direct

CNLTD142A3 Net-Direct

CNLTD72A3 Net-Direct

DIBBC2314S21W Net-Direct

DIRLC2214M21W Net-Direct

DIRBB2007S21W Net-Direct

4928, and 4924. Optimized for use in server cabinet applications.

™

Air Inlet Duct, 1 RU that resides in-line and below switch provides cold aisle airow to
Cisco^ Nexus N2K-C2148T-1GE, N2K-C2248TP-1GE, and N2K-C2232PP-10GE fabric extenders and
Cisco^ WS-C4948E-F, WS-C4948E-F-S, and WS-C4948E-F-E. Optimized for use in server
cabinet applications.

™

Air Inlet Duct designed for Cisco^ Catalyst 4900M switch. Consists of one 2 RU inlet duct
and a side duct.

™

Air Inlet Duct designed for Cisco^ Catalyst 6504-E switch. Consists of 2 RU top and 2 RU
bottom inlet ducts and a side duct.

™

Air Inlet Duct designed for Cisco^ Nexus 7009 switch. Consists of 3 RU top and 3 RU bottom
inlet ducts and a side duct.

™

Air Inlet Duct designed for Cisco^ MDS 9506 switch. Consists of 3 RU top and 3 RU bottom
inlet ducts and a side duct.

™

Air Inlet Duct designed for Cisco^ MDS 9513 switch. Consists of 2 RU top and 3 RU bottom
inlet ducts and a side duct.

™

Air Inlet Duct designed for Cisco^ Catalyst 6509-E switch. Consists of 2 RU top and 2 RU
bottom inlet ducts and a side duct.

™

Air Inlet Duct designed for Cisco^ Nexus 7004 switch. Consists of one 2 RU inlet duct and
a side duct.

Exhaust Ducts

DERLCC6509A Net-Direct™ Air Exhaust Duct for Net-Access™ N-Type 1070mm Depth Cabinets.

DERLCC9513A Net-Direct

DERLCC7009A Net-Direct

Designed for Cisco^ 6509 switch.

™

Air Exhaust Duct for Net-Access™ N-Type 1070mm Depth Cabinets.
Designed for Cisco^ 9513 switch.

™

Air Exhaust Duct for Net-Access™ N-Type 1070mm Depth Cabinets.
Designed for Cisco^ 7009 switch.

DERLCC6513A Net-Direct

DIRLC2214M21W

^Cisco is a registered trademark of Cisco Technologies, Inc.

DIRBB2007S21W

Exhaust Ducts

32

visit www.panduit.com/Cabinets

™

Air Exhaust Duct for Net-Access™ N-Type 1070mm Depth Cabinets.
Designed for Cisco^ 6513 switch.

Net-Direct™ In-Cabinet 7018 Ducting and 7018 Accessories

Part Number Description

7018 Ducting Solution

DIEBCC7018B

DIRLD0425S27W

DIEBCC7018B Net-Direct™ Air Inlet and Exhaust Ducting (blanking panels not included) designed for Cisco^ Nexus

DIRLD0425S27W Net-Direct

DIRLC7018VP51 Net-Direct

DIRLC7018VP4248 Net-Direct

7018 switch in a 1000mm wide Net-Access™ N-Type Cabinet.

™

Cisco^ Nexus 7018 switch in a 1000mm wide Net-Access

Cisco^ Nexus 7018 switch in a 1000mm wide Net-Access™ N-Type Cabinet.

Cisco^ Nexus 7018 switch in a 1000mm wide Net-Access™ N-Type Cabinet .

Air Inlet Ducting with left and right side blanking panels for 42/48 RU cabinet designed for

™

Air Inlet Ducting with left and right side blanking panels for 51 RU cabinet designed for

™

Air Inlet Ducting with right side only blanking panel for 42/48RU cabinet designed for

™

N-Type Cabinet .

7018 Cabinet Kits

N1000EXT Extension kit to expand 800mm wide x 1200mm deep Net-Access™ N-Type Cabinet to 1000mm.

For use with cabinets N8229BS, N8529BS, and N8829BS.

7018 Vertical Blanking Panels

DIRLC7018VP51

NVBPA7018B Vertical blanking panels with pass-through holes for 42 RU through 48 RU 1000mm wide cabinet.

N-Type Cabinet Split Doors

N2SD1000 One set of split doors (used front or back) for 1000mm wide Net-Access™ N-Type Cabinet 42 RU.

™

N-Type Cabinet 45 RU.

DIRLC7018VP4248

N5SD1000 One set of split doors (used front or back) for 1000mm wide Net-Access

N8SD1000 One set of split doors (used front or back) for 1000mm wide Net-Access™ N-Type Cabinet 48 RU.

NVPDUB7018 Net-Access® N-Type PDU Bracket for 1000mm wide cabinets.

N1000EXT

NVBPA7018B

NVPDUB7018

^Cisco is a registered trademark of Cisco Technologies, Inc.

visit www.panduit.com/Cabinets

33

SmartZone™ Network-Enabled Rack PDUs North America

Part Number Description
P1L2B1L2N16BQA0 For aggregate and per outlet power monitoring with switching, 30 A Single Phase, Horizontal Rack PDU, 208V, 12

P1T2B1L2N08ATA0 For aggregate and per outlet power monitoring, 30 A Single Phase Horizontal Rack PDU, 208V, 6 IEC C-13 and 2

Q1L1B1F0A24AFA0 For aggregate and per outlet power monitoring with switching, 20 A Single Phase Vertical Rack PDU, 208V, 18 IEC

Q1L2B1L2N24AFA0 For aggregate and per outlet power monitoring with switching, 30 A Single Phase Vertical Rack PDU, 208V, 18 IEC

Q1L2B1P3N24AFA0 For aggregate and per outlet power monitoring with switching, 30 A Three Phase Vertical Rack PDU, 208V, WYE,

Q1L2B2G6N24AFA0 For aggregate and per outlet power monitoring with switching, 60 A Three Phase Vertical Rack PDU, 208V, Delta,

Q1N2B1L2N30AHA0 For aggregate power monitoring, 30 A Single Phase, Vertical Rack PDU, 208V, 24 IEC C-13 and 6 IEC C-19

Q1N2B1N3N30AHA0 For aggregate power monitoring, 30 A Three Phase Vertical Rack PDU, 208 V, Delta, 24 IEC C-13 and 6 IEC C-19

Q1N2B2W6N30AHA0 For aggregate power monitoring, 60 A Three Phase Vertical Rack PDU, 208V, Delta, 24 IEC C-13, 6 IEC C-19

Q1S2B2C3N24AFA0 For aggregate power monitoring with switching, 60 A Single Phase Vertical Rack PDU, 208V, 18 IEC C-13 and 6

Q1S2B2G6N24AFA0 For aggregate power monitoring with switching, 60 A Three Phase Vertical Rack PDU, 208V, Delta, 18 IEC C-13

Q1S2B2T6N24AFA0 For aggregate power monitoring with switching, 50 A Three Phase Vertical Rack PDU, 208V, Delta, 18 IEC C-13

Q1T2B2C3N24AFA0 For aggregate and per outlet power monitoring, 60 A Single Phase Vertical Rack PDU, 208V, 18 IEC C-13 and 6

IEC C-13 and 4 IEC C-19 locking receptacles, and NEMA L6-30P plug

IEC C-19 locking receptacles, and NEMA L6-30P plug.

C-13 and 6 IEC C-19 receptacles, and NEMA L6-20P plug.

C-13 and 6 IEC C-19 locking, and NEMA L6-30P plug.

18 IEC C-13 and 6 IEC C-19 locking receptacles, and NEMA L21-30P plug.

18 IEC C-13 and 6 IEC C-19 locking receptacles, and IEC 60309 - 9H 3P+E blue splash proof plug.

locking receptacles, and NEMA L6-30P plug.

receptacles, and NEMA L15-30P twist lock plug.

receptacles, and IEC 60309-9H 3P+E plug.

IEC C-19 locking receptacles, and IEC 60309 - 9H blue splash proof plug.

and 6 IEC C-19 locking receptacles, and IEC 60309 - 9H 3P+E blue splash proof plug.

and 6 IEC C-19 locking receptacles, and NEMA CS-8365c plug.

IEC C-19 locking receptacles, and IEC 60309 -6H 2P+E plug.

34

visit www.panduit.com/Cabinets

SmartZone™ Network-Enabled Rack PDUs Global

Part Number Description
P1T1B3H0A08ATA0 For aggregate and per outlet power monitoring, 16 A Single Phase Horizontal Rack PDU, 230V 6 IEC C-13 and 2

Q1L2B2P6M24AFA0 For aggregate and per outlet power monitoring with switching, 32 A Three Phase Vertical Rack PDU, 230V/400V,

Q1L2B3J2M24AFA0 For aggregate and per outlet power monitoring with switching, 32 A Single Phase Vertical Rack PDU, 230V, 18 IEC

Q1N1B3H0A30AHA0 For aggregate power monitoring, 16 A Single Phase Vertical Rack PDU, 230V, 24 IEC C-13 and 6 IEC C-19

Q1N2B2P6M30AHA0 For aggregate power monitoring, 32 A Three Phase Vertical Rack PDU, 230/400V, WYE, 24 IEC C-13 and 6 IEC

Q1N2B2Q0A30AHA0 For aggregate power monitoring, 16 A Three Phase Vertical Rack PDU, 230/400V, WYE, 24 IEC C-13 and 6 IEC

Q1N2B3J2M30AHA0 For aggregate power monitoring, 32 A Single Phase Vertical Rack PDU, 230V, 24 IEC C-13 and 6 IEC C-19

Q1S2B2P6M24AFA0 For aggregate power monitoring with switching, 32 A Three Phase Vertical Rack PDU, 230V/400, WYE, 18 IEC

Q1S2B2Q0A24AFA0 For aggregate power monitoring with switching, 16 A Three Phase Vertical Rack PDU, 230V/400V, WYE, 18 IEC

Q1S2B3J2M24AFA0 For aggregate power monitoring with switching, 32 A Single Phase Vertical Rack PDU, 230V, WYE, 18 IEC C-13

Q1T1B3H0A24AFA0 For aggregate and per outlet power monitoring, 16 A Single Phase Vertical Rack PDU, 230V, WYE, 18 IEC C-13

IEC C-19 locking receptacles, and IEC 60309-6H 2P+E plug.

WYE 18 IEC C-13 and 6 IEC C-19 locking receptacles, and IEC-60309-6H 3P+N+E plug.

C-13 and 6 IEC C-19 locking receptacles, and IEC-60309-6H 2P+E plug.

receptacles, and IEC 60309-6H 2P+E plug.

C-19 receptacles, and IEC 60309-6H 3P+N+E plug.

C-19 receptacles, and IEC 60309-6H 3P+N+E plug.

receptacles, and IEC 60309-6H 2P+E plug.

C-13 and 6 IEC C-19 locking receptacles, and IEC 60309 -6H 3P+N+E plug.

C-13 and 6 IEC C-19 locking receptacles, and IEC-60309-6H 3P+N+E plug.

and 6 IEC C-19 locking receptacles, and IEC 60309 -6H 2P+E plug.

and 6 IEC C-19 locking receptacles, and IEC 60309-6H 2P+E plug.

visit www.panduit.com/Cabinets

35

SmartZone™ Gateway-Enabled Rack PDUs North America

Part Number Description
GM-A0252BL For aggregate power monitoring, vertical, 30 A, single phase, 208V, 24 IEC C-13 and 6 IEC C-19 receptacles,

GM-A0255BL For aggregate power monitoring, vertical, 30 A, three phase, 208V, delta, 24 IEC C-13 and 6 IEC C-19 receptacles,

GM-A0257BL For aggregate power monitoring, vertical, 60 A, single phase, 208V, 24 IEC C-13 and 6 IEC C-19 receptacles, IEC

GMPO-A0276BL For aggregate and per outlet power monitoring, horizontal 1 RU, 30 A, single phase, 208V, 6 IEC C-13 and 2 IEC

GMPO-A0277BL For aggregate and per outlet power monitoring, vertical, 60 A, single phase, 208V, 18 IEC C-13 and 6 IEC C-19

GMS-A0280BL For aggregate power monitoring with switching, vertical, 60 A, three phase, 208V, delta, 18 IEC C-13 and 6 IEC

GMS-A0283BL For aggregate power monitoring with switching, vertical, 60 A, single phase, 208V, 18 IEC C-13 and 6 IEC C-19

GMS-A0284BL For aggregate power monitoring with switching, vertical, 50 A, three phase, 208V, delta, 18 IEC C-13 and 6 IEC

GMSPO-A0286BL For aggregate and per outlet power monitoring with switching, horizontal 1 RU, 30 A, single phase, 208V, 12 IEC

GMSPO-A0288BL For aggregate and per outlet power monitoring with switching, vertical, 60 A three phase, 208V, delta, 18 IEC C-13

GMSPO-A0289BL For aggregate and per outlet power monitoring with switching, vertical, 30 A, three phase, 208V, WYE, 18 IEC C-13

GMSPO-A0291BL For aggregate and per outlet power monitoring with switching, vertical, 30 A, single phase, 208V, 18 IEC C-13 and

GMSPO-A0292BL For aggregate and per outlet power monitoring with switching, vertical, 20 A single phase, 208V, 18 IEC C-13 and

NEMA L6-30P plug, LCD display, with serial port for connection to Gateway.

NEMA L15-30P plug, LCD display, with serial port for connection to Gateway.

60309 - 6H 2P+E, LCD display, with serial port for connection to Gateway.

C-19 locking receptacles, NEMA L6-30P plug, LCD display, with serial port for connection to Gateway.

receptacles, IEC 60309-6H 2P+E plug, LCD display, with serial port for connection to Gateway.

C-19 locking receptacles, IEC 60309 - 6H 3P+E, LCD display, with serial port for connection to Gateway.

receptacles, IEC 60309-6H 2P+E plug, LCD display, with serial port for connection to Gateway.

C-19 locking receptacles, NEMA CS-8365C plug, LCD display, with serial port for connection to Gateway.

C-13 and 4 IEC C-19 locking receptacles, NEMA L6-30P plug, LCD display, with serial port for connection
to Gateway.

and 6 IEC C-19 locking receptacles, IEC-60309-9H 3P+E plug, with serial port for connection to Gateway.

and 6 IEC C-19 locking receptacles, NEMA L21-30P plug, with serial port for connection to Gateway.

6 IEC C-19 locking, NEMA L6-30P plug, with serial port for connection to Gateway.

6 IEC C-19 receptacles, NEMA L6-20P plug, LCD display, with serial port for connection to Gateway.

36

visit www.panduit.com/Cabinets

SmartZone™ Gateway-Enabled Rack PDUs Global

Part Number Description
GM-A0258BL For aggregate power monitoring, vertical, 32 A, three phase, 230V/400V, WYE, 24 IEC C-13 and 6 IEC C-19 recep-

GM-A0259BL For aggregate power monitoring, vertical, 16 A, three phase, 230/400V, WYE 24 IEC C-13 and 6 IEC C-19

GM-A0263BL For aggregate power monitoring, vertical, 16 A, single phase, 230V, 24 IEC C-13 and 6 IEC C-19 receptacles, IEC

GM-A0265BL For aggregate power monitoring, vertical, 32 A, single phase, 230V, 24 IEC C-13 and 6 IEC C-19 receptacles, IEC

GMPO-A0275BL For aggregate and per outlet power monitoring, horizontal 1 RU, 16 A, single phase, 230V, 6 IEC C-13 and 2 IEC

GMPO-A0278BL For aggregate and per outlet power monitoring, vertical, 16 A, three phase, 230V, 18 IEC C-13 and 6 IEC C-19

GMS-A0281BL For aggregate power monitoring with switching, vertical, 32 A, single phase, 230V, 18 IEC C-13 and 6 IEC C-19

GMS-A0282BL For aggregate power monitoring with switching, vertical, 16 A, three phase, 230V/400V, WYE 18 IEC C-13 and 6

GMS-A0285BL For aggregate power monitoring with switching, vertical, 32 A, three phase, 230V/400, WYE 18 IEC C-13 and 6 IEC

GMSPO-A0287BL For aggregate and per outlet power monitoring with switching, vertical, 32 A, three phase, 230V/400V, WYE 18 IEC

GMSPO-A0290BL For aggregate and per outlet power monitoring with switching, vertical, 32 A, single phase, 230V, 18 IEC C-13 and

tacles, IEC 60309 - 6H 3P+N+E plug, LCD display, with serial port for connection to Gateway.

receptacles, IEC 60309-6H 3P+N+E plug, LCD display, with Serial port for connection to Gateway.

60309-6H 2P+E plug, LCD display, with Serial port for connection to Gateway.

60309 - 6H 2P+E plug, LCD display, with Serial port for connection to Gateway.

C-19 locking receptacles, IEC 60309 - 6H 2P+E plug, LCD display, with serial port for connection to Gateway.

locking receptacles, IEC 60309-6H 2P+E plug, LCD display, with serial port for connection to Gateway.

locking receptacles, IEC 60309-6H 2P+E plug, LCD display, with serial port for connection to Gateway.

IEC C-19 locking receptacles, IEC-60309-6H 3P+N+E plug, LCD display, with serial port for connection to Gate­way.

C-19 locking receptacles, IEC 60309-6H 3P+N+E plug, LCD display, with serial port for connection to Gateway.

C-13 and 6 IEC C-19 locking receptacles, IEC-60309-6H 3P+N+E plug, with serial port for connection to Gateway.

6 IEC C-19 locking receptacles, IEC-60309-6H 2P+E plug, with serial port for connection to Gateway.

visit www.panduit.com/Cabinets

37

SmartZone™ Sensors

ZEAIR-02

ZETHL-15

ZEWS-03-03

Part Number Description
ZEAIR-02 Airow Sensor

ZETHL-15 Humidity Sensor

ZEDIFFPRESS 01, 02, 03, 05 Differential Pressure Transducer

ZETHL-14 Temperature Sensor

ZEWS-03-03 Water Rope Sensor

38

visit www.panduit.com/Cabinets

SmartZone™ Sensors

ZEDIC05-01

ZESMA05-01

Part Number Description
ZEDIC05-01 Digital input sensor for use with voltage-free contacts

ZEDL05-01 Door sensor (micro switch type)

ZEDL05-02 Door contact sensor (magnetic type)

ZEDL05-01

ZEDL05-02

ZETHL-13

ZETHL-11

ZEPIR-04

ZEPIR-04 PIR sensor

ZESMA05-01 Smoke detector

ZETHL-11 Combined temperature and humidity sensor

ZETHL-13 External temperature sensor

visit www.panduit.com/Cabinets

39

Blanking Panels and Blanking Shade

Part Number Description

TLBP1

Tool-Less Blanking Panels

TLBP1S-V 19" (483mm) width for 3/8" cage nut holes (may be used with or without cage nuts installed). 1 RU.

TLBP2

TLBPBPT1S

FLBSIMS

TLBP2S-V 19" (483mm) width for 3/8" cage nut holes (may be used with or without cage nuts installed). 2 RU.

TLBP1R-V 19" (483mm) width for tapped rails. 1 RU.

TLBP2R-V 19" (483mm) width for tapped rails. 2 RU.

Pass-Through Blanking Panels

TLBPBPT1S 19" (483mm) width for 3/8" cage nut holes (may be used with or without cage nuts installed).

1 RU, with pass-through areas.

Blanking Shade

FLBSIMS Full-length blanking shade blanks out 1-51 consecutive rack units on standard 19.00" (482.6mm) wide

vertical mounting rails; black.

40

visit www.panduit.com/Cabinets

Sealing Accessories

Part Number Description

CTGN1X5

CTGN3X5

CTGN6X6

CTCN1X5

CTCN3X5

CTNBZL6X6

Cool Boot ® Cabinet Top Air Sealing Fitting

CTGN1X5 Used to seal off 1" x 5" cabinet top openings when cables are routed through the top of a cabinet. Airtight

CTGN3X5 Used to seal off 3" x 5" cabinet top openings when cables are routed through the top of a cabinet. Airtight

CTGN6X6 Used to seal off 6.5" x 6.5" cabinet top openings when cables are routed through the top of a cabinet.

Cabinet Top Cover and Cable Protection Bezel

CTCN1X5

CTCN3X5

CTNBZL6X6 Used to provide a protective edge for cables routed through the 6.5" x 6.5" cabinet top openings after

Blanking Foam Strips

BFS100X2000 Adhesive-backed blanking foam strips conform to minimize gaps and prevent bypass air within network

Cool Boot® Raised Floor Air Sealing Grommet

™

fabric and Ultra-Cinch
of network equipment and reduce energy costs. For use with 600mm wide Net-Access

fabric and Ultra-Cinch
of network equipment and reduce energy costs. For use with 700mm, 800mm, and 1000mm wide
Net-Access™ Cabinets.

Airtight fabric and Ultra-Cinch
cooling of network equipment and reduce energy costs. For use with 600mm, 700mm, 800mm, and
1000mm wide Net-Access™ Cabinets.

Used to seal off 1.5" x 5" cabinet top openings. Can also be used to add the CTGN1X5 to openings where the
snap-on cover has been removed. For use with Net-Access™ Cabinets.

Used to seal off 3.5" x 5" cabinet top openings. Can also be used to add the CTGN3X5 to openings where the
snap-on cover has been removed. For use with Net-Access™ Cabinets.

knock-outs are removed. Can also be used to add the CTGN6X6 to openings where knock-out has been
removed. For use with Net-Access

cabinets. Removable and repositionable acrylic-based adhesive is aggressive to provide suitable strength,
however, will not leave residue on equipment. 4.0" x 100" roll perforated 1.0" in width and 20.0" in length.

Tie close top of fabric, minimizing hot air bypass around cables to improve cooling

™

Tie close top of fabric, minimizing hot air bypass around cables to improve cooling

™

Tie close top of fabric, minimizing hot air bypass around cables to improve

™

Cabinets.

™

Cabinets.

BFS100X2000

RFG12X

RFG12X4SMY Overall size of 12" x 4" (304.8mm x 101.6mm) allows for 10.2" x 2.2" (259.1mm x 55.9mm) maximum capac-

ity. Surface mount product can be installed over any opening less than 10.2” x 2.2” (259.1mm x 55.9mm).

RFG12X4Y Overall size of 12" x 4" (304.8mm x 101.6mm) allows for 10.2" x 2.2" (259.1mm x 55.9mm) capacity.

Includes exible sub-grommet to prevent damage to cable from sharp edges of cut oor tile.

visit www.panduit.com/Cabinets

41

Telecommunications Grounding Accessories

Part Number Description

CNBK

RGCBNJ660P22

RGS134-1Y

CNBK Green bonding cage nut, includes 50 #12-24 bonding cage nuts (.06 – .11 thick panel) and

RGCBNJ660P22 Mesh common bonding network (MCBN) jumper kit; #6 AWG (16mm

RGS1341Y Rack grounding stip kit; 78.65" (2m) length; .67" (17mm) width; .05" (1.27mm) thickness; provided

RGS134B-1 Cage nut grounding strip kit; 78.65" (2m) length; .67" (17mm) width; .05" (1.27mm) thickness;

RGS134B42-1

50 #12-24 x 1/2" bonding screws with #2 Phillips/slotted combo hex head (use 5/16" or 8mm socket).

lug on grounding strip stide; provided with .16oz. (5cc) of antioxidant, two each #12-24 x 1/2", M6 x
12mm, #10-32 x 1/2" and M5 x 12mm thread-forming screws and a copper compression HTAP for
connecting to the SBG (MCBN) in sizes ranging from #6-#2 AWG (16 – 25mm2).

with .16oz (5cc) of antioxidant, one grounding sticker, three each #12-24 x 1/2", M6 x 12mm,
#10-32 x 1/2" and M5 x 12mm thread-forming screws.

provided with .16oz (5cc) of antioxidant, one grounding sticker, three cage nut bonding studs,
eight #12-24 bonding nuts and three stip clips.

Equipment grounding strip kit, 42 RU, for cage nut mounting rails.

2

); 60" (1.52m) length; 45° bent

Std.

Pkg.

Qty.

1

1

1

1

RGESD2B-1

RGS134B42-1

RGS134B-1

RGS134B48-1

RGESDWS

RGRB19Y

RGRB19CN

RGS134B48-1

RGESD2B-1 ESD port kit for cage nut rail fasteners: two-hole ESD port with 5/8" hole spacing, provided with an

RGESDWS Adjustable fabric ESD wrist strap with 6' coil cord, banana plug, 1 megohm resistor and 4mm snap. 1

RGRB19Y Grounding busbar; 19" (483mm) length; tin-plated; fourteen holes arranged for exibility in mounting;

RGRB19CN Grounding busbar; 19" (483mm) length; tin-plated; twenty holes arranged for exibility in mounting

Refer to www.panduit.com/grounding for detailed information on the complete line of StructureGround™ Grounding Sytem products.

Equipment grounding strip kit, 48 RU, for cage nut mounting rails.

ESD protection sticker, 16oz. (5cc) of antioxidant, two cage nut bonding studs and two #12-24
bonding nuts.

provided with two each #12-24 x 1/2" and M6 x 12mm thread-forming screws.

with twenty #12-24 x 1/2" hex head screws installed; mounting hole sets have 5/8" (15.9mm) spacing;
provided with two cage nut bonding studs and four #12-24 bonding nuts.

1

1

1

42

visit www.panduit.com/Cabinets

Energy Efficient Data Center Cabinet System

A Part of Panduit’s Converged Infrastructure Solutions

Panduit Converged Infrastructure Solutions embody the next wave of systems integration and risk management by aligning and harmonizing
critical systems to support the delivery of secure, energy-efcient, always-on, real-time data and services. Energy Efcient Cabinet Systems
are one of the key pillars of the Panduit Converged Infrastructure Solutions portfolio that include:

®

Data Center Infrastructure Management (DCIM) — Panduit
end-to-end physical to logical view of your data center and extended enterprise. SmartZone
data center’s space, power, and capacity planning through 10% OpEx savings in energy costs, 75% faster moves, adds, and changes (MACs),
and 80% faster mean time to repair (MTTR).

SmartZone™ Solutions including hardware, software, and services that provide

™

Solutions enable effective optimization of your

Data Center Advisory Services — Panduit Data Center Advisory Services provide a full range of physical infrastructure layer services
to help you assess, design, and maintain resilient, sustainable solutions that deliver operational exibility to reduce costs by up to 20%,
and meet future requirements.

High Speed Data Transport (HSDT) Copper and Fiber Cabling Systems — Panduit HSDT Solutions are both protocol and media
agnostic, delivering maximum exibility during planning, designing, commissioning, and operation of the data center. Our HSDT
Solutions enable advanced network architectures such as 10/40/100 Gig Ethernet LANs and 8/16/32 Gig Fibre Channel SANs and
can provide a 10% improvement in network throughput.

Converged Infrastructures — Panduit helps reduce deployment times up to 65% and mitigates the risk of adopting
new technologies with reliable and robust Converged Infrastructures. Panduit utilizes optimized reference designs collaboratively
engineered with our partners, to enhance the physical infrastructure of their technology platforms and seamlessly integrate physical
and logical systems.

Physical Infrastructure Foundation — Critical to the deployment of our Data Center solution is the physical infrastructure
foundation in the data center, which includes such items as:

Pathways: Provide the best method to route and manage the growing amount of data and power cabling while
ensuring high levels of network performance

Zone Cabling: Serves as a main distribution point for a particular zone, increasing network exibility, manageability,
accessibility, and efciency

Bonding and Grounding: Provides a high quality, visually veriable and dedicated grounding path to maintain
system performance, improve network reliability, and protect network equipment and personnel

Identication and Labeling: Enhance the appearance of installations by presenting a clear and efcient way
to label according to TIA/EIA-606-A standards

visit www.panduit.com/Cabinets

43

Transform Your

Physical Infrastructure

Call or visit us online,

we can show you how.

Panduit Corp.

World Headquarters

Tinley Park, IL 60487

[e-mail]

US and Canada: 800.777.3300

Europe, Middle East, and Africa:

44.20.8601.7200

Latin America: 52.33.3777.6000

Asia Pacific: 65.6305.7575

©2016 Panduit Corp. ALL RIGHTS RESERVED. Printed in the U.S.A. RKCB37--SA-ENG Replaces RKCB30--SA-ENG
2/2016

www.panduit.com