Page 1
RapidID Scanner Quick Start Guide
Part Number: RPDSCN
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
RapidID cable identification system requires the following three components:
• Panduit RapidID copper & fiber patch cords
• Panduit barcode scanner (RPDSCN)
• Apple or Android tablet running RapidID software
: Display;
1.
Display scanner’s Working mode, Power,
1.
Time, Barcode content, etc.
: Scan button;
: Boot button;
2.
2.
: Back to home;
3.
4.
: Menu button;
3.
: Long press to enter menu;
PN657
5.
Using the Panduit Barcode Scanner (RPDSCN),
Scan barcode below to enter BLE mode.
: OK button;
When you select the function you want
4.
to set, press this button to confirm.
: Long press for 2 seconds to shut down.
5.
: Indicator light;
Confirm Scanner
in BLE mode
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 7
Page 2
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
IMPORTANT BLUETOOTH BLE SETUP INFORMATION
* Bluetooth BLE mode devices connect in software operates differently than traditional Bluetooth HID
devices which uses the tablet OS Bluetooth settings to configure and pair. BLE devices only require
Bluetooth to be enabled in the tablet OS Bluetooth settings but will pair using the RapidID software
settings.
PN657INSTALLATION INSTRUCTIONS
Home Page
• Starting at the "Home" page, go to "Settings",
Settings Page
• On the Settings page, under "Select Barcode Scanner (BLE)", pressing "<Unspecified>" will bring up the
BLE scanner configuration page.
"BleManagerState" will display "PoweredOn" if the tablet OS’s Bluetooth services are functioning
properly and listening for BLE devices. If not make sure Bluetooth is enabled in tablet OS Bluetooth
ttings.
se
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 7
Page 3
© Panduit Corp. 2021
Connecting BLE Scanner (cont’d)
Confirm the scanner # on the web,
matches the # on the scanner
INSTALLATION INSTRUCTIONS
Scanner Setup Page
PN657INSTALLATION INSTRUCTIONS
Scanner Setup Page
Click “Scan Now” to search for your BLE scanner (Verify your scanner is turned on and in BLE
mode) then select your scanner. The scanner will appear as “Scanner XXX” with XXX being the
number at the top of the Scanners display.
Once connected the RapidID software will display the name of your scanner in the top right corner
and will automatically attempt to connect to the previously used scanner.
You are now ready to scan barcodes in Capture and Match modes.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 7
Page 4
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
PN657INSTALLATION INSTRUCTIONS
Capture Mode
Capture mode can be used to document and verify patch cord installations.
From the Home page press capture to enter capture mode.
Begin by entering the module name of the equipment you will be documenting. Clicking <Unspecified>
in the module field will allow you to enter a new module name.
Set module name
Capture Page
After entering a new module name click back to return to the capture page.
Validate that the port
number is the correct value.
Scan cable barcode for the port location specified.
*It is up to the RapidID user to verify the correct module name and port number are being scanned*
Repeat the capture process for
additional modules.
When both cable ends have been
scanned, RapidID will display
matching connections.
Capture Page
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 4 of 7
Page 5
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
Capture mode verifying previously saved results.
PN657INSTALLATION INSTRUCTIONS
Save and Export:
Results can be saved and shared with other mobile devices by saving and exporting. Results can be
exported to excel spreadsheet, DCIM, or NMS by exporting CSV file.
Save and export page
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 5 of 7
Page 6
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
Match Mode
Match Mode is useful for quickly finding the other end of a RapidID cable without documenting its
location.
Starting at the “Home” page, pressing “Match” will bring up match mode.
Begin by scanning the first RapidID barcode on a RapidID cable (may be either an “A” or “B” RapidID
label).
NOTE: The Patch field is not required to be documented in order to utilize the Match feature.
PN657INSTALLATION INSTRUCTIONS
Before scanning first cable
After scanning first cable
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 6 of 7
Page 7
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
PN657INSTALLATION INSTRUCTIONS
After scanning the first barcode, any following barcode scans will be compared to the reference value
and display a checkmark if it is the same cable, or an X if it is not the same cable.
Match Mode - Correct cable
Match Mode - Incorrect cable
To begin the process again with a different cable press “Restart”
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 7 of 7
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...