Panduit R4P36CN, PR2VD08 Installation Manual

Download

Page 1

PATCHRUNNERTM 2 Vertical Managers and Racks

Part Number(s): See Sheet 2

INSTALLATION INSTRUCTIONS

V00029MX_REV01

Table of Contents

Description Page

Part Numbers and Part Contents.....................................................................................................2

Door Removal..................................................................................................................................3

Installation of Vertical Managers to Racks.......................................................................................4

Door Installation...............................................................................................................................5

Finger Removal and Replacement..................................................................................................7

End Panel Installation......................................................................................................................8

Waterfall Installation.......................................................................................................................10

Other Compatible Accessories.......................................................................................................12

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 1 of 13

Page 2

INSTALLATION INSTRUCTIONS

PART CONTENTS

(1) PATCHRUNNER

2 Vertical Cable Manager with (1) door per side (8) M10 Serrated Flange Bolts (8) M10 Serrated Flange Nuts

V00029MX_REV01

PATC HRUNNERTM 2 Vertical Cable Managers may be installed with either side facing forward.

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 2 of 13

Page 3

Door(s)

Vertical Cable Manager

To remove door(s), turn both knobs outward.

Note: If the installer does not wish to fully remove the door while finishing the Vertical Cable Manager installation then he/she may opt to open the side of the door closest to the rack. Door opening is illustrated on page 7 of this document.

Door Removal

INSTALLATION INSTRUCTIONS

V00029MX_REV01

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 3 of 13

Page 4

Vertical Cable Manager

Rack

Vertical Cable Manager

Installation view with larger capacity side of Vertical Cable Manager facing forward

Installation view with smaller capacity side of Vertical Cable Manager facing forward

Top two Positions (Use front rack holes)

Middle Position (Use rear rack hole)

Bottom Position (Use front rack hole)

Top two Positions (Use front rack holes)

Middle Position (Use rear rack hole)

Bottom Position (Use front rack hole)

Detail Views for Larger Capacity Side Facing Forward

Detail Views for Smaller Capacity Side Facing Forward

M10 Serrated Flange Bolt & M10 Serrated Flange Nut

INSTALLATION INSTRUCTIONS

V00029MX_REV01

Installation of Vertical Cable Managers to Racks

Regardless of the height of the part, and regardless of whether the rack is 2-Post or 4-Post, the Vertical Cable Manager will mount to the rack in 4 places using (4) M10 Serrated Flange Bolts and (4) M10 Serrated Flange Nuts.

The racks have pairs of mounting holes where the Vertical Cable Manager can be mounted, but the Vertical Cable Manager is designed to use only one mounting hole per pair.

If mounting with the larger capacity side facing forward, the bottom will use the front rack hole, the middle will use the rear rack hole, and the top will use the front rack hole.

If mounting with the smaller capacity side facing forward, the bottom will use the rear rack hole, the middle will use the front rack hole, and the top will use the rear rack hole.

Install Vertical Cable Manager to Rack using (4) M10 Serrated Flange Bolts and (4) M10 Serrated Flange Nuts.

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 4 of 13

Page 5

Slots

Hinge Pins

Door Knobs in locked position

Slots (1) not shown

Hinge Pins

Door Installation

INSTALLATION INSTRUCTIONS

V00029MX_REV01

Align Door Hinge Pins on 4 sides to slots on door supports and simply push closed. The door knobs will be in locked position as shown.

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 5 of 13

Page 6

Left knob shown in engaged position

Door open to right

Right knob shown in engaged position

Door open to left

INSTALLATION INSTRUCTIONS

To remove door, follow instructions given on page 3. To open door to the right, turn left knob counterclockwise until engaged. To open door to the left, turn right knob clockwise until engaged.

V00029MX_REV01

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 6 of 13

Page 7

Finger Removal and Replacement

To Remove Fingers:

Step 1:

Using a flathead screwdriver, gently pry up plastic latches in (4) places indicated while at the same time applying forward pressure to the finger section.

Latch location

Fingers removed for clarity

Step 2:

Push out the finger section toward the inside of the manager.

Fingers removed for clarity

To Replace Fingers:

Align finger mounting tabs with mounting slots on manager.

Place the finger mounting tabs under the steel flange on the manager, aligning them with the mounting slots,then push the finger section toward outside of the manager until an audible “click” is heard. Note: Because the part is long, the installer may have to push the finger section out in several spots before it is secured.

INSTALLATION INSTRUCTIONS

V00029MX_REV01

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 7 of 13

Page 8

8 foot rack

M10 X 16 Serrated Hex Head Bolt & M10 Serrated Hex Head Nut

7 foot rack

M10 X 16 Serrated Hex Head Bolt & M10 Serrated Hex Head Nut

8 foot rack

integrated hook

square on manager

bottom panel

diamond indicates bottom of panel

integrated hook

bottom panel

7 foot rack

square on manager

INSTALLATION INSTRUCTIONS

End Panel Installation to PATCHRUNNERTM 2 Vertical Managers

Part Number(s): PR2VEP, PR2VEPWH, PR2VEP96

Installing Bottom Panel:

V00029MX_REV01

Step 1: Use integrated hook at top of bottom panel to attach to square located on manager as shown.

Step 2: Fasten using (2) M10 x 16 serrated hex head bolts and (2) M10 serrated hex head nuts.

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 8 of 13

Page 9

align mounting holes

top of cable manager

integrated hooks

7 foot rack

align mounting holes

top panel

8 foot rack

top of cable manager

integrated hooks

align mounting holes

top panel

(2) M6 x 16mm serrated hex head bolts and (2) M6 serrated hex head nuts

(1) M10 x 16mm serrated hex head bolt and (1) M10 serrated hex head nut

7 foot rack

(2) M6 x 16mm serrated hex head bolts and (2) M6 serrated hex head nuts

(1) M10 x 16mm serrated hex head bolt and (1) M10 serrated hex head nut

8 foot rack

Installing Top Panel:

INSTALLATION INSTRUCTIONS

V00029MX_REV01

Step 1: Use integrated hooks at top of panel to attach over the top of the manager, aligning mounting as shown.

Step 2: Fasten using (2) M6 x 16mm serrated hex head bolts and (2) M6 serrated hex head nuts. Step 3: Fasten (1) additional M10 x 16mm serrated hex head bolt and (1) M10 serrated hex head nut.

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 9 of 13

Page 10

INSTALLATION INSTRUCTIONS

Waterfall Installation for PATCHRUNNERTM 2 Vertical Managers and Open Racks

Part number: PR2VWF, PR2VWFWH

Width adjustment of PR2VWF.

1) Adjust the width of the waterfall to fit your rack by loosening the (4) Phillips head screws (do not remove) and align them with the corresponding markers for your specific rack.

2) Tighten the (4) Phillips head screws.

INSIDE

MARKERS

OUTSIDE MARKERS

V00029MX_REV01

Waterfall slots

(4) M6 x 8mm Screws

Waterfall mounting bracket

(4) M6 x 8mm Screws

Waterfall mounting bracket

Backbone

For R2P: INSIDE MARKERS

1) Align waterfall slots around the backbone part of the manager as shown.

2) Place waterfall mounting bracket under rack between the top angles so that flanges will stop the bracket. Align holes in bracket with holes in waterfall.

3) Fasten components together using (4) M6 x 8mm screws.

For R2P6S: INSIDE MARKERS

1) Align waterfall slots around the backbone part of the manager as shown.

2) Place waterfall mounting bracket under rack between the top angles so that the flanges will stop the bracket. Align holes in bracket with holes in waterfall.

3) Fasten components together using (4) M6 x 8mm screws.

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 10 of 13

Page 11

INSTALLATION INSTRUCTIONS

V00029MX_REV01

Waterfall Installation for PATCHRUNNERTM 2 Vertical Managers and Open Racks (Cont.)

Waterfall slots (4) M6 x 8mm

Screws

Backbone

Waterfall mounting bracket

Waterfall slots

(2) M6 x 12mm Screws

Backbone

For ER4P: INSIDE MARKERS

1) Align waterfall slots around the backbone part of the manager as shown.

2) Place waterfall mounting bracket under rack between the top angles so that flanges will stop the bracket. Align holes in bracket with holes in waterfall.

3) Fasten components together using (4) M6 x 8mm screws.

For R4P: OUTSIDE MARKERS

1) Align waterfall slots around the backbone part of the manager as shown.

2) Align holes in waterfall with holes in rack.

3) Fasten components together using (2) M6 x 12mm screws & (2) M6 serrated nuts.

(2) M6 serrated nuts

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 11 of 13

Page 12

Wire retainer clips

WR5E-X-Wire Retainer clips

To install Wire Retainer clips, place open end of clip around the leg of a finger on the vertical cable manager.

Spool Removal/Replacement Step 4: Pull back on angled flange

while applying upward pressure.

Step 5: Repeat steps 1-3.

Step 2: Push buttons through back- bone until mounting face is flush with backbone.

Installation of Hole Blanking Plugs (PR2VBPK)

Press disks over pass through holes and press into place.

Angled flange

Step 3: Apply downward pressure until plastic spool clicks into place.

Mounting face

Mounting Leg Slots

Fingers removed for clarity

Step 1: Align buttons with mounting leg slot

Installation of Spools (PRSP5 or PRSP7)

INSTALLATION INSTRUCTIONS

Other Compatible Accessories (sold separately)

V00029MX_REV01

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 12 of 13

Page 13

Top Panel

Bottom Panel

Waterfall

Vertical Cable Manager

Doors

Vertical Cable Manager and Accessories on a 2-Post Rack

Vertical Cable Manager and Accessories on a 4-Post Rack

Rack

INSTALLATION INSTRUCTIONS

V000029MX_REV01

For Instructions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp

www.panduit.com

Page 13 of 13

E-mail:

techsupport@panduit.com

Phone:

866-405-6654