Panduit PZWMC1230W Installation Manual

Download

Page 1

0.8"

Mounting

Holes

4.5"

16.0"

Mounting Holes

Footprint with Cabinet Open

25.0"

Cabinet Width

PANZONE Wall Mount Cabinet

Part Numbers: PZWMC

INSTRUCTIONS CM315E

Parts Included: (1) - Extra Door Spacer (8) - Keys (1) - Roll of Tak-Ty (12) - #12-24 Screws (1) - Removable Top Vent Cover Panel

PZWMC12W

Cabinet with Windowed Door

Location Footprint

CABINET

DEPTH

25.0 45.1

30.0 50.1

RU DIM “B”DIM “C”

12 20.7” 23.8” 18 31.2” 34.3” 26 45.2” 48.3”

DIM “A”

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Page 1 of 11

Page 2

INSTRUCTIONS CM315E

PANZONE Wall Mount Cabinets can be installed in a hinged right or hinged left application. For your installation, determine which side of the cabinet will hinge. The cabinet is shown hinged left. Mounting surface must have sufficient strength to support the cabinet with payload. The mounting surface must also be flat and extend beyond the overall cabinet footprint.

To open cabinet, push latch release button to dis-engage latch.

2” or 2 1/2” Conduit Knockout

Front Door with Lock

Plastic

Step 2:

To reverse rear hinge direction.

Open cabinet, and remove the latch from the rear lock. Remove the rear lock and the lock hole grommet on the opposite side. Close the cabinet and remove decorative covers on hinges. Remove the thread forming screws & lockwashers from the hinges (M5), and latches (M4), and re-install the components on the opposite sides of the cabinet. Open the cabinet and re-install the lock and grommet on the opposite sides. Re-assemble the lock latch, ensuring it locks in the downward rotation (see below).

1/2” or 3/4” Conduit Knockout

Step 1:

Remove door and side panels for ease of handling. Ensure rear latches are closed. Install (4) 3/8” mounting hardware (not provided) as shown in Location Footprint. Hardware should protrude 3/8” from wall. Mount the cabinet to the wall by hooking the keyholes over the protruding 3/8” mounting hardware. Once the cabinet is in place, carefully swing cabinet from wall and tighten the hardware securely. Re-install door and side panels. Door swing direction can be changed by rotating the door 180°. Ensure the plastic spacer is placed at

the bottom of the door hinge.

M5 Thread forming screws & lockwashers

Hinge

Lock Hole Grommet

Lock

Lock in downward

rotation

M4 Thread forming

screwsLatch

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 2 of 11

Page 3

INSTRUCTIONS CM315E

PZWMC18RR Rear Rails

1 For PZMWCGK Cabinet Jumper Grounding Kit Only

2 Recommended for direct 1:1 switch patching only

3 Recommended for direct 1:1 switch patching only

4 Default Rail Location: Recommended for traditional patching with

small gauge patch cord, Use PZBR3 or PZBR3.5 Bend Radius Posts

5 Recommended for traditional patching with standard patch cords. Use

PZBR4 Bend Radius Posts.

Step 3: To adjust the depth of the mounting rail for specific applications, remove the M6 thread forming screws and lockwashers, move the rail to the desired position and re-install mounting hardware.

Mounting Rail Installation (PZWMC12RR)

To install mounting rail use (2) M6 thread forming screws & lockwashers at desired location as shown below

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 3 of 11

Mounting Rail

Mounting Hardware

Page 4

INSTRUCTIONS CM315E

Cable Routing

Cable must be routed with an adequate slack loop to prevent cable damage. Route cable to point 1 secure to tie down with a TAK-TY. Next route cable across the bottom of the enclosure to point 2 secure to tie down with a TAK-TY. Route to the desired patch panel after securing the cables with a T

AK-TY at point 3 or 4.

Point 4

Cables Extend to Patch Panel

Point 2

Point 3

Point 1

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 4 of 11

Page 5

INSTRUCTIONS CM315E

Optional Accessories

PZWMC12W (Shown)

Cabinet with Window Door

PZWMC-CL

Combination

Lock Kit

PZCHSM2

ANZONE Horizontal

Slack Manager

PZWMC12RR PZWMC18RR PZWMC26RR

ANZONE Rear Equipment

PZBR4

ANZONE 4” Bend

Rail Kits

Radius Post Kit

PZBR3

PANZONE 3” Bend

Radius Post Kit

PZWMCFKHF

PANZONE

Fan Kit

High Flow

PZBR3.5

PANZONE 3.5” Bend

Radius Post Kit

For Technical Support: www.panduit.com/resources/install_maintain.asp

PZCFK

ANZONE Fan Kit

PZCFR

ANZONE Fan Media

Replacement Kit

Page 5 of 11

Page 6

INSTRUCTIONS CM315E

PANZONE Fan Kits (PZCFK, PZCFK-E, PZWMCFKHF, PZWMCFKHF-E)

Fan kits are installed using (4) #10-32 screws and lockwashers provided with kit as shown below. If only one fan kit is used, install the provided blank on the opposite wall using (4) #10-32 screws and lockwashers provided. For European Schuko (240V) plugs, use fan kits with ‘-E’ part numbers

Scenario 1: Switches not exceeding 120 watts of total heat output use fan kit as shown.

Scenario 2: POE (Power over Ethernet) or switches totaling over 120 watts of total heat, use two PZCFK fan kits or one PZWMCFKHF. Mount second fan

where blank is shown.

Optional: Remove Top Panel Blank for additional venting. A fan kit can be installed on top vent, but will occupy the top RU space. NOTE: Fan kits draw air into the cabinet.

M5 Thread forming screws

Top Panel Blank

Fan Kit Blank

Note: When using switches with side air intake and opposite side exhaust use one fan without fan blank

Fan Kit

#10-32 Screws and Lockwashers (8 Places)

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 6 of 11

Page 7

INSTRUCTIONS CM315E

PANZONE Horizontal Slack Manager

Install tray using (4) #12-24 x 1/2 screws provided at desired RU as shown in figure 3. Refer to recommended layout section for optimal mounting location(s).

Screw Mounting Locations

Bend Radius Post Installation

Bend radius posts can be installed at any rack location using (1) #12-24 x 2.5" [(1) #12-24 x 1.5” for PZBR3] screw provided as shown in Figure 1. Post can be customized by removing tabs as show in Figure 2. Note: Post may be installed over active equipment mounting locations.

Figure 3

Figure 1

Figure 2

Bend Radius Post

Score Line

#12-24 x 2.5" Screw

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 7 of 11

Page 8

Cam Lock Spacer Rings

Combination locks including Cylinder Nut, Retaining Screw, Lock Washer, Flat Washer and Direction Setting Washer

Figure 1

Cam Lock Spacer Rings

Combination locks including Cylinder Nut, Retaining Screw, Lock Washer, Flat Washer and Direction Setting Washer

Figure 1

.640 .650

.755 .765

DIA.

Figure 2

Cam from lock

Figure 3

Cylinder Nut

Spacer Ring

Combination Lock Head

PZWMC* Cabinet Surface

Lock Cylinder

Cylinder Nut Installed on Back of Cabinet

Figure 4

Figure 5

Spacer RIng

Lock Head

Figure 6

PANZONE Lock Kits (PZWMC-CL)

Kit Contents

• Combination locks (2)

• Spacer rings (2)

• Cylinder nuts (2)

• Retaining screw (2)

• Lock washers (2)

• Flat washers (2)

• Direction setting washers (2)

INSTRUCTIONS CM315E

Mounting Cutout

Installation

• Remove the existing locks from the cabinet and save cams for later use. (Figure 2)

• Remove the Cylinder Nut from the Combination Lock and insert the Spacer Ring over the Lock Cylinder. (Figure 3)

• Install the Combination Lock onto the Cabinet and tighten the Cylinder Nut. The Lock Head should be spaced away from the Cabinet Surface. (Figures 3 &

• Remove the Retaining Screw, Lock Washer, Flat Washer, and Direction Setting Washer.

• Pull the Lock Head from the cylinder and rotate until oriented in the desired direction. (Figures 5-7)

For Technical Support: www.panduit.com/resources/install_maintain.asp

Cam will rotate right

Page 8 of 11

Cam will rotate left

Direction Setting Washer

Figure 7

Page 9

INSTRUCTIONS CM315E

Figure 11

Figure 10

Spacer Ring

Lock Head

Reset Button

Push reset button with pin

Scroll numbers to desired combination

Figure 9

Installation (continued)

• Install the remaining parts in the following order: Direction Setting Washer, Cam (saved from previous lock), Flat Washer, Lock Washer, and Retaining Screw. (Figure 7)

• Set the lock to the factory combination 0-0-0.

• Test lock rotation direction. Adjust cam angle if

necessary

To Change Combination:

• Set the lock to the previous combination or factory combination (0-0-0).

• Push reset button with pin. (Figure 9)

• While reset button is pushed, scroll numbers to the desired combination. (Figure 9)

• Release the reset button to set the combination.

Cam (saved) from previous lock)

Lock Washer

Retaining Screw

Flat Washer

Direction Setting Washer

Figure 8

To Hide the Reset Button:

• Set the lock to the desired combination.

• Remove the direction setting washer, cam. flat washer. lock washer, and retaining screw. (Figure

12)

• Pull out the lock head and rotate 180º. (Figures 10-11)

• Reinstall the direction setting washer, cam, flat washer, lock washer, and retaining screw. (Figure

12)

Cam (saved) from previous lock)

Lock Washer

Retaining Screw

Flat Washer

Direction Setting Washer

Figure 12

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 9 of 11

Page 10

INSTRUCTIONS CM315E

Recommended Layout (18 RU)

Recommended Layout (26 RU)

2 RU of Blanking Panel

2 RU of 24 Port Patch Panels

PZCHSM2

1 RU of Active Equipment

2 RU of 24 Port Patch Panels

PZCHSM2

2 RU of Active Equipment

PZCHSM2

2 RU of 24 Port Patch Panels

2 RU of Blanking Panel

PZCHSM2

Recommended Layout (12 RU)

24 Port Patch Panel

PZCHSM2

24 Port Patch Panel

PZCHSM2

Active Equipment

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 10 of 11

Page 11

INSTRUCTIONS CM315E

Recommended Cable Routing Guide

Place patch cord slack around furthest spool as feasible to provide best possible cable management

Never cross over center line of horizontal slack manager with cable slack

Top View of PZCHSM2

Typical patch cord length is 4 feet minimum Route patch cords as shown to avoid crossover

Recommended Mounting Locations for Bend Radius Posts

Typical patch cord length is 5 feet minimum Route patch cords as shown to avoid crossover

Routed to top Horizontal Slack Manager

For instuctions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp

Lower Horizontal Manager

www.panduit.com

Page 11 of 11

Recommended Mounting Locations for Bend Radius Posts

Route patch cords going to top horizontal slack towards the outside of the cabinet to avoid cross overs with patch cords going to lower slack manager.

E-mail:

techsupport@panduit.com

Phone:

866-405-6654