Page 1
PANZ
ONE
Building Automation System Enclosure (Economy)
PANZ
© Panduit Corp. 2013
ONE
Active Wall Mount Enclosure (Economy)
INSTRUCTIONS CM698
PZAEWM6E
List of Components:
(1) PZASEWM6E Enclosure
(1) Panel Door
(1) Installation Instruction
(4) 3RU Equipment Mounting Brackets
(2) M5 Button Head Torx Screws
(10) M6 Hex Head Screws
(6) Pack of [4] #12-24 Screws
(1) Pack of [25] #12-24 Cage Nuts
THIS PRODUCT HAS A MAXIMUM LOAD RATING OF 100 LBS.
NOTE - Some views in this document may vary
slightly from your actual enclosure.
PZBASE3E
List of Components:
(1) PZBASE3E Enclosure
(1) Panel Door
(1) Installation Instruction
(2) 3RU Equipment Mounting Brackets
(2) M5 Button Head Torx Screws
(4) M6 Hex Head Screws
(3) Pack of [4] #12-24 Screws
(1) Pack of [12] #12-24 Cage Nuts
THIS PRODUCT HAS A MAXIMUM LOAD RATING OF 60 LBS.
Knockout for.50” and.75”
Conduit (4 plcs.)
Knockout for 1.75" and 2"
Conduit (8 plcs.)
Louvered Vents
Adjustable 3RU Equipment
Mounting Brackets
(4 plcs. - PZAEWM6E)
(2 plcs. - PZBASE3E)
Knockouts for
T70 Raceway
(4 plcs.)
Venting for a 4" Fan
(2 plcs.)
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
(view shown with door removed)
Page 1 of 4
Page 2
INSTRUCTIONS CM698
Step 1: Mounting Enclosure to Wall / Electrical Box Installation
1.1 Locate the wall studs (16" on center in most U.S.
cases). PANDUIT recommends mounting the top
of the enclosure at 6’ from the floor.
1.2 Determine if you will be mounting the electrical box
in the wall.
If Mounting Electrical Box in the Wall: Remove
desired breakout from back of enclosure. After
electrical box is completely installed, mount enclosure to wall using 4 screws. Enclosure designed to
use #14 screws or M6 screws. (See figure 1.3)
Top
Mounting eyelets
Cable
Breakout
6’
Electrical
Breakout
36”
Floor
2 X 4 Stud
16"
24"
Bottom
Mounting eyelets
1.2
Electrical Box
(2 plcs.)
For Technical Support: www.panduit.com/resources/install_maintain.asp
1.3
Page 2 of 4
Page 3
INSTRUCTIONS CM698
Step 2: Door Removal and Installation
2.1 Use key to turn lock 1/4 turn
2.2 Pull top of door away from enclosure
3.3 Lift door up and away from enclosure
3.4 Reverse steps to install door
1/4 Turn Lock
Step 3: Optional Fan Installation (if required, sold separately)
3.1 Break out vent space on bottom of enclosure.
3.2 Place fan over opening. Line up the bottom fan
cover to the outside of enclosure and screw
into place.
3.3 Line up top fan cover and screw into place.
3.4 Determine the length of the power cord that is
desired. Strip back the insulation on the cord
and terminate to the plug.
3.5 Attach the power cord. The fan can be plugged
Break out
vent space
into an the electrical box inside the enclosure.
Step 4: Optional Back Plate Installation (PZBASE3E ONLY, sold separately)
4.1 Position Back Plate (p/n PZBASE3EBP -orPZBASE3EPBP) inside PZBASE3E enclosure.
4.2 Secure Back Plate to enclosure with [4] M5
Serrated Hex Nuts (use 8mm socket wrench).
[4] M5 Serrated Hex Nuts
(use 8mm socket wrench)
PZBASE3EBP
-or-
PZBASE3EPBP
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 4
PZBASE3E ONLY
Page 4
INSTRUCTIONS CM698
Step 5: 3RU Equipment Mounting Bracket Installation
5.1 Locate and install 3RU Equipment Mounting Brackets. Either Cage Nut cutouts or #12-24 tapped mounting holes
can be used; brackets are reversible. Brackets mount in vertical, horizontal, or 45º diagonal positions.
5.2 Depending on bracket orientation, use number of M6 hex head screws listed below (use 10mm socket wrench).
5.3 Install brackets in pairs in mirrored locations on left and right sides of enclosure.
3RU Equipment
3RU Equipment
Mounting Bracket
VERTICAL ORIENTATION
[2] - M6 Hex Head Screws
Mounting Brackets
INSTALL IN PAIRS
3RU Equipment
Mounting Bracket
HORIZONTAL ORIENTATION
[3] - M6 Hex Head Screws
M6 Hex Head Screws
(use 10mm socket wrench)
3RU Equipment
Mounting Bracket
45º DIAGONAL ORIENTATION
[2] - M6 Hex Head Screws
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 4 of 4
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...