Page 1
PANVIEW iQ (PViQ) Patch Panel
Part Numbers: PVQ-MIQPU24, PVQ-MIQPS24
© Panduit Corp. 2009
1.
PANVIEW iQ Patch Panel
INSTALLATION INSTRUCTIONS
Hardware Components
Rack Mounting and Grounding
2.
Install screws
in 4 places
PM Installation
EM Installation
Cable
Management
EM Installation
EM Installation
Use ONLY
LTIMATE ID
Label Covers
supplied grounding screws
(6) #12-24 x 0.5"
Grounded Bonding
PN465B
(6) M6 x 1.0 x 16(4) U
Grounded Bonding
Screws*
* Only 4 screws are needed for installation.
provide appropriate
grounding, the following
screws are recommended:
• Thread Forming Screw,
M5 x 12mm
(Part # RGTSM5-C)
• Thread Forming Screw,
#10-32 x 1/2"
(Part # RGTS1032-C)
Screws*
If supplied screws
do not fit or work
with your rack or
rack cabinet to
While PViQ Patch Panels work interchangeably with either
the Panel Manager (PM) or the Expansion Module (EM), it is
recommended that PViQ Patch Panels be placed in a manner
that will efficiently accommodate one (1) PM for every three
(3) EMs, with appropriate cable management installed for
proper cable routing. NOTE: PM can be arranged at either
the top or bottom of order depending on need or preference.
Mount the PViQ Patch Panel onto the face of
the rack or rack cabinet using four (4) of the
supplied grounding screws as shown. Use
either the #12-24 x 0.5" or M6 x 1.0 x 16
screws depending on the rack or cabinet.
PViQ Patch Panels MUST
grounded to ensure accurate system
operation.
MINI-COM Module Installation (Recommended) Cable Routing
3.
With the PViQ Patch Panel secured to the rack or cabinet, proceed to
install terminated jack modules into the patch panel (as shown above).
NOTE: The PViQ Patch Panel accepts all M
Modules and LC Fiber Adapters.
INI-COM Copper Jack
be properly
Leave room for
Mounting Bracket
It is advisable to prepare cable management by routing cables into a
left/right and upper/lower separation as you install the terminated jack
modules (as shown above) to reserve appropriate space for the
addition of mounting bracket later.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 2
Page 2
© Panduit Corp. 2009
INSTALLATION INSTRUCTIONS
Label / Label Cover Installation
PN465B
4.
Label*
Label Cover
Suggested Label Solutions for TIA/EIA-606-A Compliance
Patch Panel
Part Number
All
PViQ
Patch Panels
Laser/Ink Jet Desktop
Printer Label
UILJ6
PANT
HER
LS8E Hand-
Held Printer Label
UILS8BW
C
OUGAR
LS9 Hand-
Held Printer Label
UILS8BW
To label PViQ Panel according to TIA/EIA-606-A standard, ULTIMATE ID
labels (not included) should be created and installed (as shown). Label
covers (included) should be installed to protect the label.
* Write on labels are not included with this patch panel per TIA-EIA-606-A
standard which states: “To maximize legibility, all labels shall be printed or
generated by a mechanical device, and shall not be written by hand.”
(Refer to table above for label products)
WARNINGS:
If a non-PANDUIT power source is used, it must:
• Provide over current protection appropriate to the size of the power wiring connected to the PViQ System.
• Provide an isolated (SELV) source per National requirements.
• Be certified for use with ITE equipment per National requirements.
• Provide a nominal 12VDC source to the PM (min. 11.4VDC and max 12.6VDC).
• Provide a 12VDC output which is electrically isolated from earth ground (minimum 1500 V isolation).
• Have an output power rating of minimum 30W, which is sufficient for powering PViQ System and associated loads.
PViQ European Emissions Warning:
Product is not intended for use in a residential environment. Use of this product in residential areas may cause electromagnetic interference.
Notes:
1. Never touch un-insulated communications wiring or terminals unless the communication line has been disconnected at the network interface.
2. Only trained and qualified service personnel should install or service PViQ Systems.
3. Before installing or servicing PViQ or communication wiring, be aware of the potential for electrostatic discharge (ESD).
ATTENTION:
Observe precautions for handling electrostatic sensitive electronic devices when installing this product. Ensure that you are properly grounded with a wrist
strap or equivalent while installing PM or EM modules.
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 2 of 2
E-mail:
cs@panduit.com
Fax:
(708) 444-6993
Loading...