Page 1
PRINT UNSCALED AT 100%
Table Top Box, Cable Nook
Part Number(s): PND100
© Panduit Corp. 2018
INSTALLATION INSTRUCTIONS
Installation precautions
• For best results, place the Table Top Box, Cable Nook
in a dry area away from dust and moisture.
• To prevent fire or shock, do not expose this unit to
water or moisture. Do not place the Table Top Box,
Cable Nook in direct sunlight, near heaters or heatradiating appliances, or near any liquid. Exposure to
direct sunlight, smoke, or steam can harm internal
components.
• Handle carefully and never lay the Table Top Box on
the thin bezel. Dropping, jarring or striking may
damage the bezel.
• Never place fingers inside the openings in the sides of
the unit or along the bezel edges. The sharp edges
may cause serious injury.
PN625
Parts Included:
(1) Table Top Box
(1) Plate
(4) Plate Mounting Screws
(2) Mini-Com Faceplate
(2) NetKey Faceplate
(4) Faceplate Mounting Brackets
(4) Faceplate Mounting Screws
(8) Bracket Screws
(4) Table Mounting Brackets w/
Screws
(2) Cable Clamps & Screws
(1) Fastener Tool
Cleaning
• Surfaces should be cleaned with a dry cloth. Never use
strong detergents or solvents, like alcohol or thinner. Do
not use a wet cloth or water to clean the unit.
Operation
• The access door opens to a 90-degree angle and then
slides into the unit. The door remains open
until all the cables are connected. The access door should
be closed with the cables routed through the curved
opening to prevent damage to the unit and to prevent
liquids from entering the opening.
• • Additionally, the cover should be closed when
not in use to prevent liquids or other debris from
damaging the unit.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 5
Page 2
PRINT UNSCALED AT 100%
© Panduit Corp. 2018
Mounting
Brackets
w/ Screws
4x
6-32 Screw
Plate to Housing
4x per Plate
INSTALLATION INSTRUCTIONS
Bezel
PN625
Access
Door
Housing
NetKey or Mini-Com
Modules
(not included)
Faceplate
(NetKey or
Mini-com)
6-32 screw
Bracket to Module
Faceplate 2x per
Faceplate
Plate
Brackets 2x per
Faceplate
4-40 screw
Bracket to Plate
4x per Faceplate
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 5
Page 3
PRINT UNSCALED AT 100%
© Panduit Corp. 2018
INSTALLATION INSTRUCTIONS
PN625
Use cut-out
template on
(page 5)
Tabletop
Housing
Min. thickness 0.5" [1.27cm]
Max. thickness 3.5" [8.89cm]
Mounting
Brackets and
screws (4)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 5
Page 4
PRINT UNSCALED AT 100%
© Panduit Corp. 2018
PND400
Cord Pass-Through
Faceplate
Mounting Bracket
& Screws
HDMI Retractor
Cable Box
INSTALLATION INSTRUCTIONS
Accessories
PN625
Parts Included:
(1) Cord Pass-Through Faceplate
(1) HDMI Retractor Cable Box
(1) Mounting Bracket & Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 4 of 5
Page 5
6.66”
[16.916cm]
7.46”
[18.948cm]
0
1
23
0123
4
5
cm
Inch
R 0.5”
[1.27cm]
PRINT UNSCALED AT 100%
© Panduit Corp. 2018
INSTALLATION INSTRUCTIONS
Table Top Box, Cable Nook cut-out template
PN625
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 5 of 5
techsupport@panduit.com
E-mail:
Phone:
866-405-6654
Loading...