Panduit PE2VFD10 Installation Manual

Download

Page 1

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 1 of 13

V00029RB

INSTALLATION INSTRUCTIONS

PATCHRUNNERTM 2 Enhanced Vertical Managers

Table of Contents

Description Page

Part Configurations and Contents ...................................................................................................2

Door Support Installation …………..................................................................................................3

Orientation of Vertical Manager to Rack .......................................................................................4

Installation of Vertical Manager to Rack .......................................................................................5

End of Row Bracket Condition (Optional) ……………………...........................................................6

Finger Installation..............................................................................................................................7

Door Installation ...…………………...................................................................................................8

EIA 19” Equipment Vertical Mounting ……………………………………………………….……………9

End Panel Installation......................................................................................................................11

Other Compatible Accessories........................................................................................................12

Part Numbers

Style

Front/Rear Two doors

Front Only

Single Door

Front/Rear

Single door

7ft

Tall

PE2VD06

PE2VFD06

PE2VSD06

PE2VD08

PE2VFD08

PE2VSD08

PE2VD10

PE2VFD10

PE2VSD10

PE2VD12

PE2VFD12

PE2VSD12

8ft

Tall

PE2VD0696

PE2VFD0696

PE2VSD0696

PE2VD0896

PE2VFD0896

PE2VSD0896

PE2VD1096

PE2VFD1096

PE2VSD1096

PE2VD1296

PE2VFD1296

PE2VSD1296

Add "WH" as a suffix to the part numbers listed above to identify a white part, such as PE2VD06WH

Tools required:

3mm Allen Wrench (Door Support installation) 17mm Wrench (Rack installation) 18mm Wrench (Rack installation) 5mm Allen Wrench (Optional End of Row Bracket installation)

Page 2

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 2 of 13

INSTALLATION INSTRUCTIONS

V00029RB

Front / Rear Assembly Contents

(1) PATCHRUNNER

2 Enhanced Vertical Cable

Manager (2) Door Support assemblies – Qty 2 (3) PATCHRUNNER

2 door – Qty 2

(4) Molded cable management left finger kits

7ft – Qty 6 8ft – Qty 8 (5) Molded cable management right finger kits

7ft – Qty 6 8ft – Qty 8 (6) Hardware Kit (not shown)

Includes:

M12 Serrated Flange Bolts and Hex Nuts – Qty 6

End of Row Bracket with (2) M6 Socket Head Cap

Screws

M5 Flat Head hex drive screws – Qty 12

Front Only Assembly Contents

(1) PATCHRUNNER

2 Enhanced Vertical Cable

Manager

(2) Door Support assemblies – Qty 2 (3) PATCHRUNNER

2 door – Qty 1

(4) Molded cable management left finger kits

7ft – Qty 3 8ft – Qty 4

(5) Molded cable management right finger kits

7ft – Qty 3 8ft – Qty 4

(6) Hardware Kit (not shown)

Includes:

M12 Serrated Flange Bolts and Hex Nuts – Qty 6

M5 Flat Head hex drive screws – Qty 12

Page 3

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 3 of 13

INSTALLATION INSTRUCTIONS

V00029RB

Door Support Installation

Cable manager frame assembly

Door Support assembly (2 per cable manager)

M5 flat head screws, use a 3mm hex allen wrench to secure in place at the top and bottom of the manager frame.

Bottom of the assembly is indicated by the diamond shaped cutouts on the cable manager side panels.

NOTE:

The Door Support assembly slides vertically into place in the cable manager. Orientate so that the 40/60 open areas match as shown on the next page and align mount holes. The bottom of the vertical cable manager assembly is identified by the diamond shaped cutouts at the lower edge of the side panels.

Page 4

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 4 of 13

INSTALLATION INSTRUCTIONS

V00029RB

LARGER SIDE FACING FORWARD

APPROX. 40% OF CAPACITY

APPROX. 60% OF CAPACITY

SMALLER SIDE FACING FORWARD

Determine Cable Manager Mount Orientation to the Rack

APPROX. 40% OF CAPACITY

PATCHRUNNER

2 Enhanced Vertical Cable Managers may be installed with either side facing forward.

Page 5

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 5 of 13

INSTALLATION INSTRUCTIONS

V00029RB

Installation of Vertical Cable Managers to Racks

The Vertical Cable Manager will mount to the rack in 3 locations using (3) M12 Serrated Flange Bolts and (3) M12 Serrated Flange Nuts on 2 Post and 4 Post racks regardless of size.

The racks have pairs of mounting holes where the vertical cable manager can be mounted, but the vertical cable manager is designed to use only one mounting hole per pair. Align the mount holes as shown. The mount holes used on the rack will be the forward holes on the top and bottom mount locations and the rear rack hole in the center mount location regardless of which side of the vertical cable manager is facing forward.

Installed view with 40% capacity side of the vertical cable manager facing forward

Installed view with 60% capacity side of the vertical cable manager facing

-Top Forward mount hole

-BottomForward mount hole

-MiddleRear mount hole

Page 6

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 6 of 13

INSTALLATION INSTRUCTIONS

V00029RB

End of row bracket condition (Optional)

Place end of row bracket around inside face of the rack vertical post and inside face of Vertical Cable Manager as shown.

Tighten the end of row bracket using (2) M6 x 30mm Socket Head Cap screws.

M6 x 30mm Socket Head Cap screws

End of row bracket

Inside face of rack vertical post

Inside face of vertical cable manager

Page 7

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 7 of 13

INSTALLATION INSTRUCTIONS

V00029RB

Finger Installation to PATCHRUNNERTM 2 Enhanced Vertical Managers

Finger Removal and Replacement

Step 1: Using a flat head screwdriver, gently pry up plastic latches in (4) places indicated while at the same time applying forward pressure to the finger section. Step 2: Push out the finger section toward the inside of the manager.

Align finger mount tabs with mounting slots on the manager side panels. Finger sections installed pointed up with the rounded side facing inward. Push toward the outside of the manager until you her an audible “click”.

7 ft Managers: 3 Fingers per side

8 ft Managers: 4 Fingers per side With the shorter section Installed at the top position

Latch tab location

Page 8

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 8 of 13

INSTALLATION INSTRUCTIONS

V00029RB

Door Installation

Hinge pins

Door knobs in locked position

Align Door hinge pins on 4 sides to slots on door supports and simply push closed. The door knobs will be in locked position as shown.

Hinge pins

slots

Page 9

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 9 of 13

INSTALLATION INSTRUCTIONS

V00029RB

EIA 19” Equipment Vertical Mounting Instructions

Detail View

Cable Manager Horizontal Panel

1. Mount the appropriate cage nuts to the square cutouts provided in the cable manager horizontal panels to allow mounting of EIA 19” equipment.

2. Secure equipment using appropriate screws.

Cage nut cutouts

Optional Slack Spool mount keyhole slots

Rack unit I.D. marks

Tak-Ty Hook & Loop cable tie slots

Page 10

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 10 of 13

INSTALLATION INSTRUCTIONS

V00029RB

To open the door to the right, turn the left knob counterclockwise until engaged. To open door to the left, turn the right knob clockwise until engaged.

Page 11

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 11 of 13

INSTALLATION INSTRUCTIONS

V00029RB

End Panel Installation to PATCHRUNNERTM 2 Enhanced Vertical Managers

Part Numbers: PE2VEP, PE2VEPWH, PE2VEP96, PE2VEP96WH Installing Bottom Panel:

Bottom panel with integral hooks

M10 x 16 Serrated hex head bolt and nut (4x)

Diamond cutout indicates bottom of panel

Use integrated hooks on the bottom panel to clip in place in the square cutouts on the cable manager side panels

Top panel

M10 x 16 Serrated hex head bolt and nut (2x)

Use integrated hooks on the top panel to hang in place in the front to back door support brackets and align mount holes

M6 x 16 Serrated hex head bolt and nut (2x)

Page 12

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 12 of 13

INSTALLATION INSTRUCTIONS

V00029RB

Other Compatible Accessories (sold separately)

PRSP5 and PRSP7 Slack Spools

Mount face

Angled flange for removal

Mount keyhole slots

Mount buttons

Step 1: Align spool mount buttons with keyhole slots in the cable manager horizontal panel, with the angled flange facing upwards. Step 2: Push spool mount buttons though the keyholes and apply downward pressure until the spool clicks into place. Step 3: To remove the spool, pull back on the mount flange while applying pressure upward.

Note: Spools will hold up to 14 lbs.

WR5E-X Cable Retainer Clip

To install cable retainer clips, place the open end of the clip around the leg of the molded finger on the vertical cable manager and position as required.

Cable retainer clips

Page 13

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 13 of 13

INSTALLATION INSTRUCTIONS

V00029RB

SRB19BLY, SRB19MDBL, SRB19D5BL, SRB19D7BL Strain Relief Bars

Strain relief bars can be mounted vertically in the cable manager patching area using #12-24 screws and cage nuts. Multi-Layer Strain Relief Bars can be used to create vertical channels within the manager and additional cable support and management.

Other Compatible Accessories (sold separately)

Strain Relief Bar

#12-24 screws and cage nuts supplied with the Strain Relief Bar

Top view

Strain Relief Bar

BR1B, BR2B Brush Seal Blank Panel 19” Panels

1RU or 2RU Brush Seal Blank Panels can be mounted vertically in the cable manager patching area using screws and cage nuts. Brush Seal Blank Panels allow front to back cable management while maintaining a thermal seal pass through.

Brush Seal