Page 1
PZWC35
(door removed from
(4)#8-32 X 1/4” Screws
(2)Keys
List of Hardware Components (PZWC35 and PZWC35e):
Mounting Plate for
Wireless Access Point
Installation (included)
Knockouts
for Surface
Raceway
#10-32 threaded
Grounding Studs and
Grounding Wire (included)
Double Knockout for 1/2” or 3/4”
Conduit (3 Places)
Keyed Knockout Slots for Wall
Mount applications (6 places)
Key
Key
PZWC35e
view for clarity)
Knockout view (applies to PZWC35 and PZWC35e)
PZWC35
#10-32 threaded
Grounding Studs and
Grounding Wire (included)
Mounting Plate for
Wireless Access Point
Installation (included)
Knockouts for Wireless
Access Point Antennae
Knockouts
for Surface
Raceway
PZWC35e
PANZONE Wireless Access Point Enclosure
Part Number: PZWC35, PZWC35e
© Panduit Corp. 2010
INSTALLATION INSTRUCTIONS CM501A
TABLE OF CONTENTS Page (s)
Mounting Guide................................................................................................................. 2-4
Wireless Access Point Installation..................................................................................... 5-6
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 6
Page 2
INSTALLATION INSTRUCTIONS CM501A
2
2 x 4 Stud
PZWE35
shown
1
D
A
E
B
C
PZWC35
A
D
C
B (behind door)
E
F
PZWC35e
Wall Mount Installation
Refer to the installation and configuration guidelines provided by the manufacturer of the wireless
access point to determine the optimum enclosure installation location and antenna configuration.
Please read these instructions in their entirety prior to installing the enclosure.
Step 1: Knockout Removal
1.1 Determine whether the network cable will be routed into
the enclosure through conduit or surface raceway.
Remove the appropriate knockouts.
For Conduit - Remove knockout “A”, “B” or “C”. This double knockout accommodates either 1/2” or 3/4” conduit.
For Surface Raceway - Remove knockout “D” or “E”. This
opening accommodates PANDUIT LD10 surface raceway.
1.2 Locate the wall studs. Position the enclosure on the wall
and identify which keyed knockouts should be removed. It
is recommended that two of the mounting holes be aligned
with the wall stud. Wall anchors (not included) should be
used for each additional mounting hole chosen by the
installer. Remove desired knockouts.
Optional: Flexible grommet edging can be used to cover
knockout edges if desired.
Additional Knockout Removal on
door of
PZWC35e only
1.3 Remove all six knockouts on door, indicated by the letter "F".
These openings accommodate the antennae of the Cisco
Aironet
TM
3500e Wireless Access Point.
Step 2: Mount Enclosure to Wall or Hard
Ceiling (PZWC35 and PZWC35e)
2.1 Locate the wall studs.
2.2 Hold the enclosure against the wall to mark the location of
the mounting holes.
2.3 Mount the enclosure to the wall using mounting screws and
wall anchors (not included). Enclosure designed for use with
#14 screws.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 6
Page 3
INSTALLATION INSTRUCTIONS CM501A
3
#6-32 Screws (supplied
with ceiling brackets)
4
Option A
Option B
14.25"
12.5"
In-Ceiling Mount Installation (PZWC35 and PZWC35e)
Refer to the installation and configuration guidelines provided by the manufacturer of the wireless
access point to determine the optimum enclosure installation location and antenna configuration.
Please read these instructions in their entirety prior to installing the enclosure.
Note: PANZONE Enclosures Require one of the following additional part numbers for in ceiling applications
PANDUIT Part #:PZWIFIDCB - PANZONE Wireless Access
Point In Ceiling Bracket Kit
See Step 3-4 for installation instructions See Step 5 for installation instructions
PANDUIT Part #:PZW2X2DCB - PANZONE Wireless Access Point
In Ceiling 2’x 2’ Bracket Kit
Step 3: Install Ceiling Mount Brackets
3.1 Install Ceiling Mount Brackets against side wall of the enclosure with the flanged edge facing away from the enclosure.
(see figure 2) The top of the flanged edge should be even with
the enclosure door.
3.2 Fasten the bracket to the base of the enclosure using four of
the supplied #6-32 Screws.
3.3 Repeat steps for remaining 3 Ceiling Mount Brackets.
Step 4: Prepare Ceiling Tile
4.1 When the enclosure will be mounted in a suspended ceiling, a
square hole that is approximately 12 1/2” x 14 1/4” must be
cut in the ceiling tile.
4.2 It is important that the hole be no smaller than 12 1/4” x 14”
and no larger than 12 3/4” x 14 1/2”.
lation and prevent visible gaps around the enclosure once
installed.
Note:The bottom edges of the assembled enclosure brackets can
be used as a guide to trace the square hole size onto the ceiling tile.
For Technical Support: www.panduit.com/resources/install_maintain.asp
This will ease instal-
Page 3 of 6
12.5"
14.25"
Page 4
INSTALLATION INSTRUCTIONS CM501A
6
3/8” dia hanger wire
mounting holes
(8 places)
3/8” dia hanger wire
mounting holes
(8 places)
5.1
5.2
Hinge
Hinge Slot
#6-32 Screws (supplied
with ceiling brackets)
Step 5: Installing Enclosure in Bracket
5.1 Insert enclosure into bracket as shown align hinges with the
hinge slots in bracket.
5.2 Secure the four sides of the enclosure to the bracket with (4)
#6-32 screws on each side provided with the bracket as
shown.
Step 6: Hanging Enclosure in Bracket
6.1 Hanger wire should be used to hang the enclosure
within a suspended ceiling. Important: Verify hanger
wire meets local building code. It is recommended to
use N0. 18 AWG solid steel wire as a minimum or any
comparable/equivalent wire or hanger system as
allowed by the applicable local code. Weight of the
enclosure, mounting brackets, and equipment does not
exceed 20 lbs. The enclosure is rated to hold up to
10 lbs of equipment.
6.2 Observe how the hanger wire used to hold the ceiling
support grid is secured to the building structure.
6.3 Remove one tile adjacent to the tile the enclosure will
be mounted in.
6.4 Secure four pieces of hanger wire (not included) to the
building structure. The hanger wire length will be
determined by the installer based on the building
structure dimensions above the suspended ceiling.
Extend the length of the hanger wire beyond the
surface of the ceiling by at least 6".
6.5 Add the cut ceiling tile back to the ceiling support grid.
6.6 Pull one of the four pieces of hanger wire to one corner
of the square opening in the ceiling tile. Pre-bend the
hanger wire at a 90° angle approximately 2 1/2" above
the surface of the ceiling tile. Repeat this step for the
remaining 3 hanger wires measuring to the three
remaining corners of the square opening.
6.7 Insert the enclosure into the cut ceiling tile opening.
6.8 While holding the enclosure flush with the surface of
the ceiling tile, route the hanger wire through one of the
eight 3/8" dia hanger wire mounting holes and bend up.
Pull the wire upward until the enclosure is flush with the
ceiling tile. Repeat this step using the three remaining
hanger wires to secure the three remaining corners of
the enclosure.
6.9 Visually inspect the edges of the enclosure to verify no
gaps exist between the mounting brackets and surface
of the ceiling tile. If gaps exist, pull the hanger wire
upward until the enclosure is tight against the ceiling
tile.
6.10 To secure the enclosure, wrap each hanger wire tightly
around itself a minimum of three times.
6.11 Replace the adjacent ceiling tile.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 4 of 6
Page 5
INSTALLATION INSTRUCTIONS CM501A
Wireless Access Point Installation
Access Point-Low Profile Bracket Access Point-Universal Bracket
Step 7: Connecting Vendor
Supplied Grounding Wire
7.1 AP-Low Profile Bracket: Connect Pan duit-supplied grounding wire to stud on
vendor-supplied wireless access point
mounting plate. Secure with vendor sup plied nut.
7.2 AP-Universal Bracket: Secure Panduit supplied grounding wire behind vendor supplied wireless access point mounting
bracket in orientation shown using vendor supplied screw.
Step 8: Installing Vendor-sup-
plied WAP Mounting Brackets
8.1 AP-Low Profile Bracket: Mount vendor supplied wireless access point mounting
plate to The Panduit-supplied Wireless
Access Point Mounting Plate using Pan
duit-supplied (4) #8-32 X 1/4” Screws.
Holes are aligned to outer rectangular ori
entation of holes on the mounting plate.
8.2 AP-Universal Bracket: Mount vendor supplied wireless access point mounting
frame to The Panduit-supplied Wireless
Access Point Mounting Plate using Panduit supplied (4) #8-32 X 1/4" Screws. Holes
are aligned to inner rectangular orientation
of holes on the Panduit-supplied mounting
plate.
7.1
8.1
#8-32 X 1/4" Screws
Vendor-Supplied wireless
access point mounting plate
7.2
8.2
#8-32 X 1/4" Screws
Vendor-Supplied wireless
access point mounting plate
Step 9 (PZWC35 only): Installing
Wireless Access Points
9.1 Both Bracket styles: Mount wireless
access point using the studs on the back of
the wireless access point to connect it to the
vendor-supplied wireless access point
mounting bracket. Align studs with corre
sponding holes and push down to connect.
Studs
For Technical Support: www.panduit.com/resources/install_maintain.asp
9.1
Wireless Access Point
Page 5 of 6
Wireless Access Point
Page 6
INSTALLATION INSTRUCTIONS CM501A
Step 9 (PZWC35e only): Installing
9.1
Wireless Access Points
9.1 Both Bracket styles: Mount wireless
access point using the studs on the back of
the wireless access point to connect it to the
vendor-supplied wireless access point
mounting bracket. Align studs with corre
sponding holes and push down to connect.
Studs
Step 10: Grounding
10.1 This part comes with grounding wire attatched to studs on the
enclosure base and enclosure door (see Page 1).
10.2 If a vendor-supplied grounding cable is used to ground to the
Wireless Access Point Mounting Plate (see Step 7), connect
other end to the stud on the enclosure base.
10.3 Secure with the Nuts and Washers that are on the stud.
Wireless Access Point
Wireless Access Point
10
Wire (vendor-supplied)
Note: Antennae on hinge side of enclo-
sure must be bent toward door hinges in
order to close the enclosure door.
Stud
PZWC35 with completed Wireless
Access Point Assembly
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 6 of 6
PZWE35 shown
PZWC35e with completed Wireless
Access Point Assembly
E-mail:
cs@panduit.com
Fax:
(708) 444-6448
Loading...