Panduit NFDR4X6K, NFD484, NFCDRK, NFSHLF19X18, NFR84 Instructions Manual

© Panduit Corp. 2010

Modular NETFRAME™ Rack and Accessories

Part Numbers: NFR84, NFD484, NFSK, NFDR4X6K, NFCDRK, NFVSM4, NFEDB23,
NFSHLF19X18, NFSHLF19X25, NFLRB, NFEP, NFD884, NFD1284, NFREB2, NFBRFK

INSTRUCTIONS CM281G

Optional Accessories

(2) Rear Extender
Bracket
(8) #12-24 Screws

NFREB2

(1) Spool
(2)#12-24 Screws

NFSK

ETFRAME Extender

(1) N
Door Brackets for
23” Mtg
(4) #10-32 Screws

NFEDB23

NFR84

Modular NETFRAME Rack

(2) Vertical Channels
(2) Base Angles
(1) Pack of (20) 3/8x1.00
Bolt, Lockwasher, Nut
(1) Front Top Flange
(1) Rear Top Flange
(2) Center Waterfalls
(1) Pack of (25) #12-24x1/2” Screws
(1) Grounding and Hardware Kit

Rack Assembly

Front Top
Flange

(16) Center
D-rings

NFCDRK

(8) Bend Radius Fingers

(8) D-rings

NFDR4X6K

(1) End Panel
(6)3/8”-16x1.625” Hex Bolts
3/8”-16 Hex Nuts
3/8” Split Lockwashers

NFEP

Rear Top Flange

NFBRFK

(1) Vertical
Slack Manager

NFVSM4

(1) Shelf
(4) #12-24 Screws

NFSHLF19x18
NFSHLF19x25

(shown)

19” Mounting 23” Mounting

(1) Center
Door, with
brackets

NFD884
NFD1284

(1) Ladder Rack
Bracket
(2)3/8”-16x1” Hex Bolts
3/8”-16 Hex Nuts
3/8” Split Lockwasher

NFLRB

(1) Door, 4” wide w/
Mtg Brackets
(4) #10-32 Screws

NFD484

Base Angle

Step1

Lay the two vertical channels
on the floor or a pair of sturdy
saw horses to ease installa­tion.

Install (1) Base Angle and
Front Top Flange on the verti­cal channels using (8) 3/8”
bolts, lockwashers and nuts
provided. Do not tighten.

Vertical
Channel

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Base Angle

Step 2

Roll the rack on its side to install
the other base angle and rear
top flange using (8) 3/8” bolts,
lockwashers and nuts provided.

Do not tighten.

Page 1 of 4

INSTRUCTIONS CM281G

23.875

28.40

11.00

17.00

6.00

Rear
Bracket

Front
Bracket

Shelf
Plate

#10-32 Screws

C Channel

J Slot

Flush
Mount

6 in.
Mount

Center Waterfall

Step 3

Stand the rack upright.Verify
#12-24 tapped holes are EIA
spaced at 18.31”, square the
rack and tighten bolts.
Install the two waterfalls with
the #10-32 screws provided.

Grounding Kit

(1) Barrel Lug
(1) 1/4”-20 Screw

Barrel Lug and
Grounding Screw
mounts to rear of
rack in one of four
optional places.

Rear Extender Bracket Installation
NFREB2

Use (2) #12-24 screws to secure each
bracket in desired location

(2) #12-24
SCREWS

Location Guide: 19” Rack

Mount rack to floor using the location guide below for
mounting hole and overall size information.

Shelf Installation
NFSHLF19X18, NFHSLF19X25

Attach Rear Bracket to rear of
rack at desired height with
#12-24 screws. Attach Front
Bracket to front of rack at
desired height with #12-24
screws. Attach Shelf Plate to
Front and Rear Brackets with
the #10-32 screws. The Shelf
Plate “C” Channel mates with
the bracket “J’ Slot to provide
adjustable mounting. Can be
mounted “flush” or extended 6
inches.

.

Ladder Rack Bracket Installation
NFLRB

End Panel
NFEP

NFEP attaches to

rack with (6) 3/8”­16x.625” Hex Bolts,
3/8”-16 Hex Nuts
and 3/8” Split Lock­washers provided.

NFEP

NFLRB Top Plate
attaches to Main
Bracket with (2) 3/8”­16x1” hex bolts, 3/8”-16
hex nuts and 3/8” split­lockwashers provided

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Page 2 of 4

NFLRB Top Plate
can be assembled
perpendicular to
Main Bracket to
support parallel
runs of ladder rack.

NFLRB assembles to
NFR84 using 3/8”-16x1”
hex bolt, nut, and lock­washer provided with
NFR84