Panduit NetKey NK366M**Y, NetKey NK588M**Y, NetKey NK388M**Y, NetKey NK5E88M**Y, NetKey NK5E88M**Y-Q Installation Instructions Manual
NetKey
Network Components
Keystone Cabling System
NetKey Keystone Style Jack Modules
1
2
3
4
5
6
7B
1
2
7A
Part Numbers: NK366M**Y, NK388M**Y, NK588M**Y, NK5E88M**Y, NK5E88M**Y-Q
© Panduit Corp. 2017
Remove 3" (76.2mm) of cable jacket and untwist pairs.
INSTALLATION INSTRUCTIONS
Straighten conductors and arrange in proper color sequence.
Pull conductors until outer jacket is inside cap. Bend up 90°. Cut conductors on an angle and insert into cap.
NK178D
NOTE: Cable jacket is inside the cover.
Apply pressure to cap until it clicks again. Cap must be flush on
housing.
Termination Cap Removal Instructions
--- FOR USE IN KEYSTONE STYLE OUTLETS AND PATCH PANELS ONLY ---
--- OVER FOR KEYSTONE STYLE PANEL OPENING REQUIREMENTS ---
** Denotes jack module color code.
Snap cap squarely on housing until it clicks.Trim conductors flush with cap using wire snipping tool (CWST).
Use Snap Tool (7A) or standard Slip Lock Pliers (7B).
Slide screwdriver under cap to separate from housing.Push forward and down against latch at end of guide ramp until cap releases.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 2
© Panduit Corp. 2017
18
INSTALLATION INSTRUCTIONS
--- CATEGORY 5/5E NK588/5E88 SERIES WIRING SEQUENCES ---
NK178D
WIRING DIAGRAM
Part Numbers
NK588/NK5E88
Modular Plug
Contacts
Part Number Part Number
NK366 NK388
Insulation
Displacement
Contacts
Pin #’s
WIRING DIAGRAM
“Category 5/5E” Keystone Style Jack Modules Color-Coded Wire Positions
T568A, ISDN T568B, AT&T 258A, WECO
2
1
3
5
4
6
8
7
GREEN
WHITE/GREEN
WHITE/ORANGE
WHITE/BLUE
BLUE
ORANGE
BROWN
WHITE/BROWN
R3
T3
T2
T1
R1
R2
R4
T4
2
1
3
5
4
6
8
7
ORANGE
WHITE/ORANGE
WHITE/GREEN
WHITE/BLUE
BLUE
GREEN
BROWN
WHITE/BROWN
Refer to catalog for a listing of color-coded NetKey Keystone Style Jack Modules.
--- CATEGORY 3 NK366/388 SERIES WIRING SEQUENCES ---
“Category 3” Keystone Style Jack Modules Color-Coded Wire Positions
10 Base-T EIA/TIA 568A, ISDN
1 WHT/GRN T3
2 GRN/WHT R3
3 WHT/BRN T4
4 NC
5 NC
6 BRN/WHT R4
7 NC
8 NC
EIA/TIA 568B, AT&T
258A, WECO
1 WHT/ORG T2
2 ORG R2
3 WHT/GRN T3
4 BLU R1
5 WHT/BLU T1
6 GRN R3
7 WHT/BRN T4
8 BRN R4
1 WHT/GRN T3
2 GRN R3
3 WHT/ORG T2
4 BLU R1
5 WHT/BLU T1
6 ORG R2
7 WHT/BRN T4
8 BRN R4
USOC 4-wire
in 6 pin
2 WHT/ORG T2
3 BLU R1
4 WHT/BLU T1
5 ORG R2
1
6
USOC 4-Wire
(8 Pin Jack) RJ45, USOC 8-Wire
1 NC
2 NC
3 WHT/ORG T2
4 BLU/WHT R1
5 WHT/BLU T1
6 ORG.WHT R2
7 NC
8 NC
USOC 6-Wire
(8 Pin Jack) USOC, RJ11/RJ25
1 NC
2 WHT/GRN T3
3 WHT/ORG T2
4 BLU R1
5 WHT/BLU T1
6 ORG R2
7 GRN R3
8 NC
1 BRN R4
2 WHT/GRN T3
3 WHT/ORG T2
4 BLU R1
5 WHT/BLU T1
6 ORG R2
7 GRN R3
8 WHT/BRN T4
1 WHT/GRN T3
2 WHT/ORG T2
3 BLU R1
4 WHT/BLU T1
5 ORG R2
6 GRN R3
R2
T2
T3
T1
R1
R3
R4
T4
Refer to catalog for a listing of color-coded NetKey
Keystone Style Jack Modules.
--- KEYSTONE STYLE PANEL OPENING REQUIREMENTS ---
PANEL OPENING REQUIREMENTS
KEYSTONE SERIES
Panel Thickness: (.048"-.058")
.76"–.77" (19.43mm)
.58"–.59" (14.86mm)
Notes:
1. For specified performance, follow TIA/EIA 568A installation guidelines and use equivalent or higher category twisted pair cable.
2. Keystone Style Jack Modules can terminate PVC or Plenum rated 22-24 AWG solid or stranded IWC cable with 0.048 inch (1.2mm)
maximum insulated conductor outside diameter.
3. Keystone Style Jack Modules may be reterminated a minimum of 10 times.
4. For technical and performance data, refer to catalog or consult Panduit Technical Support.
As with all Wiring Accessories, the following statements apply:
1. Never install communications wiring during a lightning storm.
2. Never install communications wiring in wet locations unless the jack is specifically designed for use in wet locations.
3. Never touch uninsulated communications wiring or terminals unless the communication line has been disconnected at the network interface.
4. Use caution when installing or modifying communication wiring.
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 2 of 2
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...