Page 1
NET-ACCESS N-Type Switch Cabinets
(Dual Hinge Door Installation)
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Dual Hinge Door (Bracket Installation)
• VIEW 1 Install Top Hinge Bracket on cabinet frame (install hinge screw and hinge pin, if necessary) - [2] PLACES
• VIEW 2 Install Lift Pin Bracket and Lift Pin Wear Plate on cabinet frame
• VIEW 3 Install Bottom Hinge Bracket, Bottom Hinge Pin Screw, Bottom Hinge Pin Locknut, and Bottom Hinge Pin
on cabinet frame -
[2] M4 Flat Head Screws
(use 2.5mm Allen Key)
-or-
[2] M5 Flat Head Screws
(use T25 Torx)
[2] PLACES
(with M4 clearance holes)
(with M5 clearance holes)
Top Hinge Bracket
-or-
Top Hinge Bracket
M5 Hinge Screw
(use 4mm Allen Key)
VIEW 1
Diamond shaped
punch out.
M4 Top Hinge Bracket
identified by a diamond
shaped punch out.
Hinge Pin
CM619B
[2] M4 Flat Head Screws
(use 2.5mm Allen Key)
Bottom Hinge Pin
Plastic Washer
Bottom Hinge Pin Locknut
Bottom Hinge Pin Screw
M6 Torx Screw
(use T30 Torx bit)
VIEW 2
Lift Pin Bracket
Lift Pin Wear Plate
VIEW 3
Bottom Hinge Bracket
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 4
Page 2
© Panduit Corp. 2015
Dual Hinge Door (Installation)
• Open both swing handles
• VIEW 1 Ensure one top latch is
• Lift door (with
• VIEW 2
• VIEW 1 Pull red finger handle to toggle top latch of
• Close both swing handles
• Close door
Latch in CLOSED Position
{See VIEW 4)
CLOSED bottom latch) onto bottom hinge pin
While supporting weight of door, align OPEN top latch with cabinet and push door against cabinet until latched
Red Finger Pull
OPEN (VIEW 3) and the other is CLOSED (VIEW 4; pull red finger handle to toggle latches)
INSTALLATION INSTRUCTIONS
open side to OPEN (VIEW 3) position
Push Door Towards Cabinet
(ensure that: both swing handles are open
and
open side latch is toggled OPEN, as
shown in
VIEW 3)
CM619B
OPEN POSITION CLOSED POSITION
VIEW 3 VIEW 4
VIEW 1
Swinghandles
VIEW 2
Lift Pin Bracket
Door Lift Pin
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 4
Page 3
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Dual Hinge Door (Removal)
• Open both swing handles
• VIEW 1
• VIEW 2 Remove door from cabinet frame by pushing top of hinged side of door away from cabinet
• Lift door off bottom hinge pin
Latch in
{See VIEW 4)
While supporting weight of door, pull red finger handle to toggle latch of open side of door to CLOSED position (VIEW 4)
Push Door Away From Cabinet
CLOSED Position
Red Finger Pull
(ensure that: both swing handles are open and
open side latch is toggled to CLOSED position as
shown in
CM619B
VIEW 1
Swinghandles
OPEN POSITION CLOSED POSITION
VIEW 2
VIEW 3 VIEW 4
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 4
Page 4
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
CM619B
Dual Hinge Door (Operation)
NOTE: Door is push-to-close. PANDUIT recommends closing handle after opening door and simply push door when closing
Door Function Adjustment (optimize door operation)
• Remove Dual Hinge Door from cabinet (or open one side at a time)
• VIEW 1 Loosen [2] Hinge Pin Screws at bottom of cabinet and raise by approximately 6 revolutions (6mm [0.25”])
• VIEW 2 Lower [2] Hinge Pin Locknuts to bottom of Hinge Pin Post Screw (if nut is not lowered; factory setting of nut is fully-lowered)
• Reinstall Dual Hinge Door (see page 2)
• VIEW 3, VIEW 4 Raise [2] Hinge Pin Locknuts until Plastic Washers touch bottom of Dual Hinge Door, then lower locknut 1 revolution
• VIEW 5 Open each side of Dual Hinge Door and tighten [2] Hinge Pin Screws
• Close Dual Hinge Door
• If Dual Hinge Door interferes with Hinge Pin Locknut or Plastic Washer, lower locknut until there is no interference
VIEW 1
Ensure BOTH swing handles are in
[2] Hinge Pin Screws
(Loosen and raise
6 revolutions)
6mm
[0.25”]
VIEW 2
closed position prior to closing door
[2] Hinge Pin Locknuts
(Lower)
Dual Hinge Door
[2] Hinge Pin Locknuts
(Raise until Plastic Washer
touches bottom of Dual
Hinge Door, then lower 1
revolution)
VIEW 3
VIEW 4
1mm
[0.04”]
VIEW 5
[2] Hinge Pin Screws
(Tighten)
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 4 of 4
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
.
Loading...