Panduit KMTRTH, KMTRTLS Installation Instructions Manual

7

MTRTH and MTRTLS TOOL CHANGEOVER KITS

© Panduit Corp. 2007

CHANGEOVER KITS:

Changeover kit allows for installation of heavy (H) cross-section MRT and MRS style ties

KMTRTH

KMTRTLS

in MTRTLS tool. Kit comes complete with one setshear finger (H), one anvil (H), three
screws, thread-lock tube and installation instructions.

Changeover kit allows for installation of standard (S) and light-heavy (LH) cross-section
MRT and MRS style ties in MTRTH tool. Kit comes complete with one setshear finger
(LS), two anvils (LH and S), three screws, thread-lock tube and installation instructions.

SAFETY PRACTICES

ALWAYS wear safety glasses when using this tool.

DO NOT place fingers near cutting blade during tool actuation.
Fingers may be pinched or injured by cutter blade.

KMTRTH and KMTRTLS

INSTALLATION INSTRUCTIONS

PA25282A01

Rev. 00 8-200

DO NOT use tool on live electrical sources.

TO REPLACE ANVIL

Remove two screws holding Anvil onto the tool. A 3/32” Allen Wrench will be required. The screws may be very
tight as they have been installed with Loctite
the tool and downward away from the tool. Set aside old Anvil. ** Place new Anvil onto bottom of the tool. The
Anvil must straddle the two plates and have the slots toward the rear. When the Anvil is slid backwards, the slots
must engage the pins. If done correctly, the hole on each side of the Anvil will align with a tapped mounting hole
below. Replace the screws applying a drop of Loctite

** IF SETSHEAR FINGER IS TO BE REPLACED AS WELL, NOW IS THE TIME TO REPLACE PER
THE INSTRUCTIONS BELOW.

®

. Once the screws are removed, slide the Anvil towards the front of

®

to each screw. See pictures below.

TO REPLACE SETSHEAR FINGER

Remove a single screw holding the Setshear Finger up onto the Sliding Detent Assembly. Use a 1/16” Allen
Wrench to remove the screw. The screw may be tight as it has been installed with Loctite
removed, slide the Setshear Finger toward the front of the tool. This should disengage it from the Sliding Detent
Assembly. Pull the Finger down out of the bottom of the tool. Installation is the reverse of these steps. When
replacing the Setshear Finger, the notch on the flat surface of the finger must
Sliding Detent Assembly. See pictures below.

engage the retaining tab on the

WHEN COMPLETE, THE LOCATING SET SCREW ON THE FRONT OF THE TOOL WILL NEED TO
BE ADJUSTED PRIOR TO TOOL USE.

®

The above names and products are the registered trademarks of their respective corporations.

Website: www.panduit.com

E-mail: [e-mail]

®

. Once the screw is

Technical Support:

See Page 4 for contact

information.

Page: 1 of 4

Anvil

Pins (2) Each Side

KMTRTH and KMTRTLS OPERATION INSTRUCTIONS

SIDE PLATE REMOVED FOR CLARITY

Setshear Finger

Anvil Mounting Screw

(Each Side)

Finger Mounting

Screw

Retaining Tab

INSTALLATION OF ANVIL OR SETSHEAR FINGER

TO REPLACE ANVIL OR SETSHEAR FINGER:
NOTE: Replace or install Anvil or Setshear Finger per table below.

ANVIL MARKS 0 1 2

SETSHEAR
FINGER MARKS

MTRTH TOOL MTRTLS TOOL

HEAVY STANDARD LIGHT HEAVY

1 2 2

SETSHEAR FINGER DIFFERENTIATION

Identifying Marks

Heavy Ties * 1 Mark

- MTRTH Tool -

Page: 2 of 4

Standard / Light Heavy Ties * 2 Marks

- MTRTLS Tool -